BS ISO 18843-2015 Aluminium oxide primarily used for the production of aluminium Method for the determination of flow time《主要用于铝生产的氧化铝 流动时间的测定方法》.pdf

《BS ISO 18843-2015 Aluminium oxide primarily used for the production of aluminium Method for the determination of flow time《主要用于铝生产的氧化铝 流动时间的测定方法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 18843-2015 Aluminium oxide primarily used for the production of aluminium Method for the determination of flow time《主要用于铝生产的氧化铝 流动时间的测定方法》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS ISO 18843:2015Aluminium oxide primarilyused for the production ofaluminium Method for thedetermination of flow timeBS ISO 18843:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 18843:2015.The UK participation in its preparation w

2、as entrusted to TechnicalCommittee CII/24, Raw materials for the aluminium industry.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its c

3、orrectapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 84997 8ICS 71.100.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strat

4、egy Committee on 30 June 2015.Amendments issued since publicationDate Text affectedBS ISO 18843:2015 ISO 2015Aluminium oxide primarily used for the production of aluminium Method for the determination of flow timeOxyde daluminium principalement utilis pour la production daluminium Mthode de dtermina

5、tion du temps dcoulementINTERNATIONAL STANDARDISO18843First edition2015-06-01Reference numberISO 18843:2015(E)BS ISO 18843:2015ISO 18843:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of th

6、is publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in t

7、he country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 18843:2015ISO 18843:2015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Principle 14 Apparatus . 1

8、5 Sample preparation . 16 Procedure. 26.1 General . 26.2 Number of determinations . 26.3 Determination . 27 Reporting of results . 28 Precision . 29 Test report . 3Annex A (informative) Results of planned trial . 5Bibliography 6 ISO 2015 All rights reserved iiiContents PageBS ISO 18843:2015ISO 18843

9、:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for wh

10、ich a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all

11、matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This

12、 document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or

13、all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users

14、and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary

15、informationThe committee responsible for this document is ISO/TC 226, Materials for the production of primary aluminium.iv ISO 2015 All rights reservedBS ISO 18843:2015ISO 18843:2015(E)IntroductionThis International Standard is based on Australian Standard, AS 2879.9, AluminaDetermination of flow ti

16、me. ISO 2015 All rights reserved vBS ISO 18843:2015BS ISO 18843:2015Aluminium oxide primarily used for the production of aluminium Method for the determination of flow time1 ScopeThis International Standard sets out a method for determining the amount of time taken for a given quantity of smelter-gr

17、ade alumina to flow by gravity through a precisely constructed standard funnel.NOTE Variations in the apparatus and other test variables can create significant inter-laboratory differences in results. (See Table A.1.)2 Normative referencesThe following documents, in whole or in part, are normatively

18、 referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.AS 4538.2, Guide to the sampling of alumina Part 2: Preparation of sa

19、mples3 PrincipleThe standard funnel is loaded with a specified mass of alumina. The time for the alumina to flow out of the funnel is determined.4 Apparatus4.1 GeneralThe test may be carried out using manual or automatic timing. An automatic device is shown in Figure 1.4.2 Funnel, precisely construc

20、ted of a corrosion resistant metal, e.g. brass or aluminium, as shown in Figure 2 with an abrasion resistant material, e.g. hardened stainless steel, insert with an outlet diameter of (3,95 to 4,00) mm; this diameter is critical.4.3 Stand, a suitable device for supporting the funnel.4.4 Timing devic

21、e, either a stop watch or automated device capable of an accuracy of 1 s.4.5 Top-loading balance, capable of weighing 100 g to the nearest 0,1 g.4.6 Sieve, with apertures within the range (300 to 400) m to remove abnormal oversize material.4.7 Container, suitable for containing the test sample.4.8 S

22、ealable container, suitable for containing and storing the funnel.5 Sample preparationThe analytical sample shall be conditioned by exposure to the laboratory atmosphere for a minimum of 2 h in a layer of 5 mm maximum thickness. The sample shall then be split as per AS 4538.2 into three INTERNATIONA

23、L STANDARD ISO 18843:2015(E) ISO 2015 All rights reserved 1BS ISO 18843:2015ISO 18843:2015(E)portions of approximately (105 to 120) g for testing. The sample shall then be screened through a sieve (4.6) and the oversize material discarded.6 Procedure6.1 GeneralThis procedure is for manually timed de

24、terminations.6.2 Number of determinationsThree determinations shall be carried out.6.3 DeterminationEach determination shall be carried out as follows.a) Ensure the funnel is clean with no surface oxides present and dry prior to use; otherwise flow times will not be reproducible. Frequent use has us

25、ually been found to be an adequate cleaning method.b) Set up the apparatus by placing the funnel (4.2) on the stand (4.3) in a vibration-free environment.c) Ensure that the funnel is secure on the stand and that the upper surface is precisely level.d) For apparatus not in frequent use, clean the fun

26、nel by passing several portions of alumina through it see a). Discard this material prior to testing.e) Take one of the prepared samples (see Clause 5) and accurately weigh a test portion of (100 0,1) g and place into the container (4.7). (See Clause 5.)f) Pour the test portion uniformly into the fu

27、nnel while manually obstructing the outlet.g) Start the flow by removing the outlet obstruction and immediately commence timing. Stop the timing as soon as all the sample has passed through the funnel. Never tap the funnel.h) Repeat the procedure with the other two test portions (Clause 5).i) Remove

28、 the funnel from the stand and wipe the funnel clean with a dry cloth. Replace it in the sealable container (4.8) to prevent damage to the outlet orifice and minimize atmospheric oxidation of the inner surface.7 Reporting of resultsReport the average of the three results to the nearest second.8 Prec

29、isionA test programme of the method in this International Standard was carried out in accordance with AS 2850. From the results of this programme, a within-laboratory repeatability (r) and between-laboratory reproducibility (R) at the 95 % confidence level as given in Table 1 should be achieved.NOTE

30、 Results of the test programme are given in Annex A.Table 1 Precision data for flow timeRepeatability (r) Reproducibility (R)2,7 9,72 ISO 2015 All rights reservedBS ISO 18843:2015ISO 18843:2015(E)9 Test reportThe test report shall include the following information:a) identification of the sample;b)

31、a reference to this International Standard, i.e. ISO 18843;c) average flow time for the sample;d) the date on which the test was carried out;e) any factors during the course of the test which may have had an effect on the results.Figure 1 Automatic flow funnel time apparatus ISO 2015 All rights rese

32、rved 3BS ISO 18843:2015ISO 18843:2015(E)Dimensions in millimetresKeyA datum line through the funnelB hardened insert with orifice shown in situ and as detailC vertical cross sectionD top view= Radius 90 typical= Datum line= Total run out (i.e. radius tolerance is 0,1 mm)= Diameter= Finish (0,2 Fine,

33、 1,.6 Standard)= Tolerance Max./Min.FINISH 3,2 UNDTOLERANCE 0,3 UNDFigure 2 Flow funnel4 ISO 2015 All rights reservedBS ISO 18843:2015ISO 18843:2015(E)Annex A (informative) Results of planned trialA planned trial of the method in this International Standard was carried out in accordance with AS 2850

34、. Samples of three smelter grade aluminas were analysed. Results were provided in quadruplicate by six laboratories. The within-laboratory (r) and between-laboratory (R) precision data (at 95 % confidence limits) and mean flow time values calculated from the results are given in Table A.1.Table A.1

35、Precision data obtained using test samplesSample Mean flow time sRepeatability (r)Reproducibility (R)S-109 47 1,5 7, 3S-110 68 3,3 10,7S-111 82 2,9 10,8 ISO 2015 All rights reserved 5BS ISO 18843:2015ISO 18843:2015(E)Bibliography1 AS 4538.1, Guide to the sampling of alumina Part 1: Sampling procedur

36、es2 AS 2879.9, AluminaDetermination of flow time6 ISO 2015 All rights reservedBS ISO 18843:2015BS ISO 18843:2015ISO 18843:2015(E) ISO 2015 All rights reservedICS 71.100.10Price based on 6 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and o

37、ther standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe b

38、ring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation proces

39、s. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer S

40、ervices team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other

41、Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have

42、instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, b

43、oth in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing

44、 Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is cur

45、rent. For further information, email .RevisionsOur British Standards and other publications are updated by amendment or revision. We continually improve the quality of our products and services to benefit your business. If you find an inaccuracy or ambiguity within a British Standard or other BSI pu

46、blication please inform the Knowledge Centre.CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that owns copyright in the information used (such as the international stand

47、ardization bodies) and has formally licensed such information to BSI for commercial publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopyin

48、g, recording or otherwise without prior written permission from BSI. Details and advice can be obtained from the Copyright & Licensing Department.Useful Contacts:Customer ServicesTel: +44 845 086 9001Email (orders): Email (enquiries): SubscriptionsTel: +44 845 086 9001Email: Knowledge CentreTel: +44 20 8996 7004Email: Copyright & LicensingTel: +44 20 8996 7070Email: NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW