BS ISO 15082-2016 Road vehicles Tests for rigid plastic safety glazing materials《道路车辆 刚塑性安全透光覆盖材料试验》.pdf
《BS ISO 15082-2016 Road vehicles Tests for rigid plastic safety glazing materials《道路车辆 刚塑性安全透光覆盖材料试验》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 15082-2016 Road vehicles Tests for rigid plastic safety glazing materials《道路车辆 刚塑性安全透光覆盖材料试验》.pdf(56页珍藏版)》请在麦多课文档分享上搜索。
1、BS ISO 15082:2016Road vehicles Tests for rigidplastic safety glazing materialsBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 15082:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 15082:2016.The UK participation in i
2、ts preparation was entrusted to Technical Committee AUE/1, Vehicle Lighting 83.140.01 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2016.Amendments
3、/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 15082:2016 ISO 2016Road vehicles Tests for rigid plastic safety glazing materialsVhicules routiers Essais pour les vitrages de scurit rigides en matires plastiquesINTERNATIONAL STANDARDISO15082Second edition2016-11-15Reference nu
4、mberISO 15082:2016(E)BS ISO 15082:2016ISO 15082:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, elect
5、ronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier
6、, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 15082:2016ISO 15082:2016(E)Foreword v1 Scope . 12 Normative references 13 Terms and definitions . 14 Test conditions . 15 Conditioning of test specimens . 16 Application of tests. 27 Optical properties te
7、st 28 Head-form/fragmentation test 28.1 Principle 28.2 Apparatus 28.3 Test specimens 38.4 Procedure 48.5 Expression of results 49 Head-form test with deceleration measurement . 59.1 Principle 59.2 Test conditions 59.3 Conditioning of test pieces . 59.4 Apparatus 59.5 Calibration procedure and adjust
8、ment of the head-form .119.6 Test pieces 129.7 Test procedure 129.8 Evaluation . 139.9 Expression of results . 1410 Ball test 1410.1 227 g ball test 1410.1.1 Principle . 1410.1.2 Apparatus 1410.1.3 Test specimens1510.1.4 Procedure 1510.1.5 Expression of results .1610.2 2260 g ball test . 1610.2.1 Pr
9、inciple . 1610.2.2 Apparatus 1610.2.3 Test specimens1610.2.4 Procedure 1610.2.5 Expression of results .1611 Abrasion resistance test 1711.1 Principle . 1711.2 Abrasion resistance under dry conditions . 1711.2.1 Apparatus 1711.3 Test specimens . 2111.4 Standardization of abrading wheels 2111.5 Proced
10、ure . 2111.5.1 Cleaning 2211.5.2 Conditioning . 2211.5.3 Initial haze measurement 2211.5.4 Abrasion . 2211.5.5 After abrasion 2311.5.6 Final haze measurement 23 ISO 2016 All rights reserved iiiContents PageBS ISO 15082:2016ISO 15082:2016(E)11.6 Expression of results . 2411.7 Abrasion resistance unde
11、r wet conditions (car wash test) .2511.7.1 Apparatus 2511.7.2 Reagents . 2711.7.3 Test specimens2711.7.4 Procedure 2811.7.5 Expression of results .2812 Cross-cut test .2812.1 Principle . 2812.2 Apparatus . 2812.3 Test specimens . 2912.4 Procedure . 2912.5 Expression of results . 3013 Chemical resist
12、ance test 3013.1 Principle . 3013.2 Chemical agents 3013.3 Test specimens . 3013.4 Test procedure 3113.5 Expression of results . 3214 Resistance to simulated weathering test .3214.1 Principle . 3214.2 Exposure apparatus . 3214.2.1 Long arc xenon lamp .3214.2.2 Measurements . 3314.3 Test specimens .
13、3314.4 Procedure . 3314.4.1 Temperature . 3414.4.2 Relative humidity .3414.4.3 Water . 3514.5 Evaluation . 3514.6 Expression of results . 3514.7 Report of test parameters . 3515 Fire resistance test 3615.1 Principle . 3615.2 Apparatus . 3615.3 Test specimens . 3615.4 Test procedure 3615.5 Expression
14、 of results . 37Annex A (informative) Flexibility/rigidity categorization test for plastic safety glazing material 38Annex B (informative) Vacuum pick-up nozzle modification 39Annex C (normative) Calibration of the washing equipment 40Annex D (informative) Calibration verification of Taber abraser .
15、42Annex E (informative) Round robin test results to determine values for AS 4000S hard-coated polycarbonate reference samples in the Taber abrasion test .44Bibliography .45iv ISO 2016 All rights reservedBS ISO 15082:2016ISO 15082:2016(E)ForewordISO (the International Organization for Standardization
16、) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be repr
17、esented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to deve
18、lop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO
19、/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during t
20、he development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning
21、of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.The committee responsible for this docume
22、nt is ISO/TC 22, Road vehicles, Subcommittee SC 35, Lighting and visibility.This second edition cancels and replaces the first edition (ISO 15082:1999), which has been technically revised. ISO 2016 All rights reserved vBS ISO 15082:2016BS ISO 15082:2016Road vehicles Tests for rigid plastic safety gl
23、azing materials1 ScopeThis document specifies commonly used test methods relating to the safety requirements for rigid plastic safety glazing materials in a road vehicle, regardless of the type of plastic of which they are composed.NOTE 1 Plastic safety glazing materials are classified as rigid or f
24、lexible by use of the test described in Annex A.NOTE 2 Further test methods might be defined in separate standards.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO150822016ROADVEHICLESTESTSFORRIGIDPLASTICSAFETYGLAZINGMATERIALS 道路 车辆 塑性 安全 透光 覆盖 材料 试验 PDF

链接地址:http://www.mydoc123.com/p-584621.html