BS ISO 14856-2001 Timekeeping instruments - Wristwatch cases - Fixing dimensions of non-spring-bar types《计时器 手表外壳 无簧杆式固定尺寸规格》.pdf

《BS ISO 14856-2001 Timekeeping instruments - Wristwatch cases - Fixing dimensions of non-spring-bar types《计时器 手表外壳 无簧杆式固定尺寸规格》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 14856-2001 Timekeeping instruments - Wristwatch cases - Fixing dimensions of non-spring-bar types《计时器 手表外壳 无簧杆式固定尺寸规格》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 14856:2001 Timekeeping instruments Wristwatch cases Fixing dimensions of nonspringbar types IS 39.040.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 14856:2001 This British Standard, having been prepared under the direction of the Sector Commi

2、ttee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 August 2001 BSI 07-2001 ISBN 0 580 38170 6 National foreword This British Standard reproduces verbatim ISO 14856:2001 and implements it as the UK national standard. The UK parti

3、cipation in its preparation was entrusted to Technical Committee STI/53, Specifications and test methods for jewellery and horology, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standa

4、rds which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard

5、 does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the respon

6、sible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cove

7、r, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsINTERNATIONAL STANDARD ISO 14856 First

8、edition 2001-02-01 Reference number ISO 14856:2001(E) Timekeeping instruments Wristwatch- cases Fixing dimensions of non-spring- bar types Instruments horaires Botes de montres-bracelets Dimensions de fixation des types sans barretteISO 14856:2001(E) ii ISO 1002 All rithgs rreseved DPF discliamer Th

9、is FDP feli amy ctnonia ededdebm tyfep.seca In aroccecnad tiwh Asebod gnisnecil ycilop, thsi feli may be pritnde ro eivwde but sllah ton eb tideed sselnu teh tyfepseca hwich are mededdeb era licdesne to dna tsniladel on teh moctupre epfrromign the ideti.gn In odgnidaolnw this file, raptise ccatpe tr

10、ehien teh serilibisnopty fo ton fnirignign sebodA gnisnecil ilopcy. The ISO tneCral Sceterarita catpecs no libaility in this aera. ebodA si a trmedarak of Adebo Stsysme Irocntarop.de teDails of teh fostware prtcudos desu to crtaee tsih PFD feli nac be fdnuo ni the Glarene Info talerive to the f;eli

11、teh PDF-taercnoi rapmateers weer tpodezimi for pritn.gni vErey cera sah eebn tkane to rusnee ttah the feli is tiusbael for ues by ISO mrebme seidob. In teh kilnuley evtne ttah a pborlme talerign to ti si f,dnuo saelpe ifnrom teh tneClar Stercearita ta the serddas givne olebw. ISO 1002 llA rithgs rre

12、sev.de Unless torehiwse sficep,dei on rapt of tihs buptacilion may be rperdecudo ro tuilidez in any form ro by nay m,snae ele-c trinoc or m,lacinahce gnidulcni tohppocoyign dna cimrfo,mli tiwtuoh repminoiss ni rwitgni fmor eitreh ISO at teh serddas olebw ro ISOs mme- reb ydob in the cuotnry fo the r

13、tseuqeer. ISO cporythgi fofiec esaC tsopael 65 1121-HC Geneva 02 Te.l + 41 22 947 10 11 Fax + 14 22 479 09 47 E-liam copyrightsio.ch Web wwwsi.oc.hISO 14856:2001(E) ISO 1002 All rithgs rreseved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of nationa

14、l standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical com- mittees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internati

15、onal organizations, governmental and non-governmental, in liai- son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the r

16、ules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the p

17、ossibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 14856 was prepared by Technical Committee ISO/TC 114, Horology, Subcommittee SC 7, Over

18、all dimensions.INTERNATIONAL STANDARD ISO 14856:2001(E) ISO 1002 All rithgs rreseved 1 Timekeeping instruments Wristwatch-cases Fixing dimensions of non-spring-bar types 1 Scope This International Standard specifies overall fixing dimensions of wristwatch-cases to which bracelets or straps are faste

19、ned by means of a set of fixing pins and tubes. This International Standard is applicable to wristwatch-cases with four or with two lugs. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this International Sta

20、ndard. For dated references, subsequent amendments to, or revisions of, any of these publica- tions do not apply. However, parties to agreements based on this International Standard are encouraged to investi- gate the possibility of applying the most recent editions of the normative documents indica

21、ted below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain reg- isters of currently valid International Standards. ISO 286-1, ISO system of limits and fits Part 1: Bases of tolerances, deviations and fits. ISO 286-2, ISO syste

22、m of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts. ISO 3765, Timekeeping instruments Wristwatches Dimensions of bracelet-to-case fastening elements ISO 6426-2:1984, Horological vocabulary Part 2: Technico-commercial definitions. 3 Terms and de

23、finitions For the purposes of this International Standard, the terms and definitions given in ISO 6426-2 and the following apply. 3.1 lug pa rtofaca setowhi chab r a ce le torastr a pisf as ten e df ora ttac hi n gth ew a tchtoth ewri st 3.2 lug hole aperture made in a lug for fastening a bracelet o

24、r a strap to a case 3.3 distance between lugs inner dimension for cases of Type 1, as shown in Figure 1 and as specified in ISO 3765 3.4 lug width outer dimensions for cases of Type 2, as shown in Figure 2 A aISO 14856:2001(E) 2 ISO 1002 All rithgs rreseved 4 Classification Wristwatch-cases are clas

25、sified in two types, as follows. Type 1: a case with four lugs arranged in pairs on each side at the axis (see Figure 1). A bracelet is fastened between these lugs by the use of a fixing pin and tube. Type 2: a case with one single lug at and one at (see Figure 2). A bracelet is fastened by the use

26、of a fixing pin and tube. 5 Forms of fastening elements See Figures 1 and 2. Figure 1 Case with two pairs of lugs (Type 1) 6 h 12 h 6 h 12 hISO 14856:2001(E) ISO 1002 All rithgs rreseved 3 Figure 2 Case with two single lugs (Type 2)ISO 14856:2001(E) 4 ISO 1002 All rithgs rreseved 6 Forms of fastenin

27、g pins and tubes See Figures 3 and 4. Figure 3 Fastening pin and slit tube Figure 4 Fastening notched pin and tubeISO 14856:2001(E) ISO 1002 All rithgs rreseved 5 7 Fixing dimensions and tolerances of wristwatch-cases, pins and tubes Fixing dimensions are given in Tables 1 to 3, together with tolera

28、nces in accordance with ISO 286-1 and ISO 286-2. Table 1 Cases of Type 1 Fixing dimensions and tolerances Dimensions in millimetres Distance a between lugs Diameter of lug hole Diameter of hole for passage o ftubef orsli torno tc hed tubes Fastening pin clearance Tolerance H12 or H13 H11 H11 H15 5 0

29、,70 6 7 8 9 1,10 10* 11 12* 1,50 13 14* 2,00 15 16* 17 18* 19 20* 21 22 24 NOTE If (distance between lugs) is less than , (lug width) (see Table 2) should be used by keeping the tolerance for (H12 or H13). a Preference should be given to the dimensions marked with an asterisk. AD 1 D 2 b 1 d 1 + 0,0

30、5 d 2 + 0,05 A 5m maAISO 14856:2001(E) 6 ISO 1002 All rithgs rreseved Table 2 Cases of Type 2 Fixing dimensions and tolerances Dimensions in millimetres Lug width Diameter of lug hole Diameter of hole for passage of tube for slit or notched tubes Fastening pin clearance Tolerance h12 or h13 H11 H11

31、H15 1,60 0,70 1,80 2,00 2,20 1,10 2,50 1,50 3,00 2,00 3,20 3,50 4,00 NOTE If (lug width) is more than , (distance between lugs) (see Table 1) should be used by keeping the tolerance for (h12 or h13). Table 3 Assembly Dimensions of fastening pins and tubes Dimensions in millimetres Fastening pin diam

32、eter a Outside diameter of tubes a (Driven-in pin) Slit tubes Notched tubes Tolerance h8 or h9 js11 js10 0,70* 1,00* 0,80 1,10 1,10 0,90* 1,20* 1,20* 1,00 1,30 1,30 1,10 1,40 1,40 1,50 1,20* 1,50 1,50* 1,30 1,60 1,60 1,40* 1,70 1,80* 1,50* 1,80 1,90* 1,60 1,90 2,00 a Preference should be given to th

33、e dimensions marked with an asterisk. a D 1 D 2 b 1 d 1 + 0,05 d 2 + 0,05 a 4m mAa d 1 d 2BS ISO 14856:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standard

34、s in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of

35、our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI

36、offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 02

37、0 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI prov

38、ides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:

39、 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Furt

40、her information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Ac

41、t 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary detai

42、ls such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.