BS EN ISO 28941-1-2008 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Designation system and basis for specifications《塑料 聚苯醚(PPE)模制和挤压成型材料 命名体系和基本规范 n》.pdf

《BS EN ISO 28941-1-2008 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Designation system and basis for specifications《塑料 聚苯醚(PPE)模制和挤压成型材料 命名体系和基本规范 n》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 28941-1-2008 Plastics - Poly(phenylene ether) (PPE) moulding and extrusion materials - Designation system and basis for specifications《塑料 聚苯醚(PPE)模制和挤压成型材料 命名体系和基本规范 n》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO28941-1:2008ICS 83.080.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics Poly(phenylene ether)(PPE) moulding andextrusion materialsPart 1: Designation system and basisfor specifications (ISO 28941-1:2008)Licensed Copy: Wang Bin, ISO/EXCHANGE CH

2、INA STANDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 28 February2009 BSI 2009ISBN 978 0 580 58541 8Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 28941-1:2008National for

3、ewordThis British Standard is the UK implementation of EN ISO28941-1:2008. It supersedes BS EN ISO 15103-1:2004 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can be o

4、btained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STA

5、NDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 28941-1December 2008ICS 83.080.20 Supersedes EN ISO 15103-1:2004 English VersionPlastics - Poly(phenylene ether) (PPE) moulding and extrusionmaterials - Part 1: Designation system and basis fors

6、pecifications (ISO 28941-1:2008)Plastiques - Matriaux base de poly(phnylne ther)(PPE) pour moulage et extrusion - Partie 1: Systme dedsignation et base de spcification (ISO 28941-1:2008)Kunststoffe - Polyphenylenether (PPE)-Formmassen - Teil1: Bezeichnungssystem und Basis fr Spezifikationen (ISO2894

7、1-1:2008)This European Standard was approved by CEN on 15 November 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliograph

8、ical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN

9、member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy,

10、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brusse

11、ls 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 28941-1:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIBS EN ISO 28941-1:2008EN ISO 28941-1:2008 (E) 3 Foreword Th

12、is document (EN ISO 28941-1:2008) has been prepared by Technical Committee ISO/TC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics“, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of

13、an identical text or by endorsement, at the latest by June 2009, and conflicting national standards shall be withdrawn at the latest by June 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be hel

14、d responsible for identifying any or all such patent rights. This document supersedes EN ISO 15103-1:2004. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyp

15、rus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 2

16、8941-1:2008 has been approved by CEN as a EN ISO 28941-1:2008 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIBS EN ISO 28941-1:2008ISO 28941-1:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2

17、 Normative references . 2 3 Designation system 2 3.1 General. 2 3.2 Data block 1. 2 3.3 Data block 2. 3 3.4 Data block 3. 4 3.5 Data block 4. 6 3.6 Data block 5. 7 4 Examples of designations . 8 4.1 Designation only. 8 4.2 Designation transformed into a specification . 9 Licensed Copy: Wang Bin, ISO

18、/EXCHANGE CHINA STANDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIBS EN ISO 28941-1:2008ISO 28941-1:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of pr

19、eparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, i

20、n liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main tas

21、k of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attentio

22、n is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 28941-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materia

23、ls. ISO 28941 consists of the following parts, under the general title Plastics Poly(phenylene ether) (PPE) moulding and extrusion materials: Part 1: Designation system and basis for specifications ISO 28941-1 is a revision of ISO 15103-1, the revision concerning principally the inclusion of melt vo

24、lume-flow rate as a designatory property and the inclusion of additional ranges of values of the other designatory properties. In order to give users time to switch from ISO 15103-1 to ISO 28941-1, ISO 15103-1 will remain in force for a number of years after publication of ISO 28941-1. During this p

25、eriod, ISO 15103-2 will effectively be Part 2 of this International Standard. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIBS EN ISO 28941-1:2008INTERNATIONAL STANDARD ISO 28941-1:2008(E) ISO 2008 All rights reserved 1Plastics Poly(phenylene ethe

26、r) (PPE) moulding and extrusion materials Part 1: Designation system and basis for specifications 1 Scope 1.1 This part of ISO 28941 establishes a system of designation for PPE thermoplastic materials, which may be used as the basis for specifications. 1.2 The types of PPE plastic are differentiated

27、 from each other by a classification system based on appropriate levels of the designatory properties a) temperature of deflection under load b) melt volume-flow rate c) Charpy notched impact strength d) flammability and on information about basic polymer parameters, intended application and/or meth

28、od of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 This part of ISO 28941 is applicable to all PPE materials, including those modified with polystyrene or polyamide or other materials. It applies to materials ready for normal use in the form of powde

29、r, granules or pellets and to materials unmodified or modified by colorants, additives, fillers, etc. 1.4 It is not intended to imply that materials having the same designation necessarily have the same performance. This part of ISO 28941 does not provide engineering data, performance data or data o

30、n processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in ISO 15103-2, if suitable. 1.5 In order to specify a ther

31、moplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see 3.1). Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIBS EN ISO 28941-1:2008ISO 28941-1:2008(E) 2 ISO 200

32、8 All rights reserved2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1

33、043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics ISO 15103-2, Plastics Poly(phenylene ether) (PPE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties 3 Designation system 3.1 General The designa

34、tion system for thermoplastics is based on the following standardized pattern: Designation Identity block Individual-item block Description block (optional) International Standard number block Data block1 Data block2 Data block3 Data block 4 Data block 5 The designation consists of an optional descr

35、iption block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous coding, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1: Identification of the pla

36、stic by its symbol PPE in accordance with ISO 1043-1 and information about the composition of the polymer (see 3.2). Data block 2: Position 1: intended application or method of processing (see 3.3). Positions 2 to 8: important properties, additives and supplementary information (see 3.3). Data block

37、 3: Designatory properties (see 3.4). Data block 4: Fillers or reinforcing materials and their nominal content (see 3.5). Data block 5: For the purposes of specifications, a fifth data block may be added containing additionalinformation. The first character of the individual-item block shall be a hy

38、phen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,). 3.2 Data block 1 In this data block, after the hyphen, poly(phenylene ether) materials are identified by the symbol PPE, i

39、n accordance with ISO 1043-1, followed by a hyphen and a code-number giving additional information on the polymer, as specified in Table 1. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 11/06/2009 08:01, Uncontrolled Copy, (c) BSIBS EN ISO 28941-1:2008ISO 28941-1:2008(E) ISO 2008 All rights

40、 reserved 3Table 1 Code-numbers used for additional information in data block 1 Code-number Material 1 PPE 2 PPE+PS 3 PPE+PA 4 PPE+another polymer not already given in this table 5 PPE+PS+another polymer not already given in this table 6 PPE+PP 7 PPE+PPS 3.3 Data block 2 In this data block, informat

41、ion about intended application and/or method of processing is given in position 1 and information about important properties, additives and colour in positions 2 to 8. The code-letters used are specified in Table 2. If information is presented in positions 2 to 8 and no specific information is given

42、 in position 1 the letter X shall be inserted in position 1. Table 2 Code-letters used in data block 2 Code-letter Position 1 Code-letter Positions 2 to 8 A Adhesives A Processing stabilized B Blow moulding B Antiblocking C Calendering C Coloured D Powder E Extrusion E Expandable F Extrusion of film

43、s F Special burning characteristics G General use G Granules G1 Pellets G3 Beads H Coating H Heat-ageing stabilized K Cable and wire coating K Metal deactivated L Monofilament extrusion L Light and weather stabilized M Moulding N Natural (no colour added) P Impact modified Q Compression moulding Q1

44、Plateable R Rotational moulding R Mould release agent S Sintering S Lubricated T Tape manufacture T Transparent V Thermoforming X No indication X Cross-linkable Y Textile yarns, spinning Y Increased electrical conductivity Z Antistatic Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 11/06/200

45、9 08:01, Uncontrolled Copy, (c) BSIBS EN ISO 28941-1:2008ISO 28941-1:2008(E) 4 ISO 2008 All rights reserved3.4 Data block 3 3.4.1 General In this data block, the temperature of deflection under load is represented by the letter A or B followed by a three-figure code-number (see 3.4.2), the melt volu

46、me-flow rate by a two-figure code-number (see 3.4.3), the impact strength by a two-figure code-number (see 3.4.4) and the flammability by a combination of code-letters and code-numbers indicating the flammability category (see 3.4.5). The code-numbers are separated from each other by hyphens. If a p

47、roperty value falls on or near a range limit, the manufacturer shall state which range will designate the material. If subsequent individual test values lie on, or on either side of, the limit because of manufacturing tolerances, the designation is not affected. NOTE Not all combinations of the valu

48、es of the designatory properties may be possible for currently available polymers. 3.4.2 Temperature of deflection under load The temperature of deflection under load shall be determined in accordance with ISO 15103-2. The possible values of the temperature of deflection under load at 1,8 MPa and 0,

49、45 MPa are divided into 17 ranges, each represented by a letter followed by a three-figure code-number as specified in Table 3 and Table 4, respectively. Table 3 Ranges of temperature of deflection under load at 1,8 MPa in data block 3 Code-number Range of temperature of deflection under load at 1,8 MPa C A050 W 50 A060 W 60 A070 W 70 A080 W 80 A090 W 90 A100 W 100 A110 W 110 A120 W 120 A130 W 130 A140 W 140 A150 W 150 A160 W 160 A170 W 170 A180 W 180 A190 W 190 A200 W 200 A210 W 210 Licensed Copy: Wang Bin, ISO/