BS EN ISO 15065-2005 Countersinks for countersunk head screws with head configuration in accordance with ISO 7721《头部外形符合ISO 7721标准的沉头螺钉的埋头孔》.pdf

《BS EN ISO 15065-2005 Countersinks for countersunk head screws with head configuration in accordance with ISO 7721《头部外形符合ISO 7721标准的沉头螺钉的埋头孔》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 15065-2005 Countersinks for countersunk head screws with head configuration in accordance with ISO 7721《头部外形符合ISO 7721标准的沉头螺钉的埋头孔》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN ISO 15065:2005 Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 The European Standard EN ISO 15065:2005 has the status of a British Standard ICS 21.060.10 BS EN ISO 15065:2005 This British Standard was published under the authority o

2、f the Standards Policy and Strategy Committee on 24 March 2005 BSI 24 March 2005 ISBN 0 580 45613 7 National foreword This British Standard is the official English language version of EN ISO 15065:2005. It is identical with ISO 15065:2005. The UK participation in its preparation was entrusted by Tec

3、hnical Committee FME/9, Nuts, bolts and accessories steering committee, to Subcommittee FME/9/3, Dimensional work on fasteners, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standard

4、s which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This pu

5、blication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible internat

6、ional/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO

7、title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEU

8、ROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO15065 February2005 ICS21.060.10 Englishversion Countersinksforcountersunkheadscrewswithhead configurationinaccordancewithISO7721(ISO15065:2005) Fraisurespourvisttefraiseavecuneconfigurationde latteconformelISO7721(ISO15065:2005) SenkungenfrSenkschrau

9、benmitderKopfformnachISO 7721(ISO15065:2005) ThisEuropeanStandardwasapprovedbyCENon3February2005. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalr

10、eferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentr

11、alSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Sp

12、ain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2005CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO15065:2005:E I

13、NESO 51:5602005 (E) 2 Foreword This document (EN ISO 15065:2005) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Threaded and non- threaded mechanical fasteners and accessories“, the secretariat of which is held by DIN. This Europea

14、n Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2005, and conflicting national standards shall be withdrawn at the latest by August 2005. According to the CEN/CENELEC Internal Regulations, the national

15、 standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portug

16、al, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Endorsement notice The text of ISO 15065:2005 has been approved by CEN as EN ISO 15065:2005 without any modifications. ENISO15065:2005 Reference number ISO 15065:2005(E) OSI 5002INTERNATIONAL STANDARD ISO 15065 First edition 2005

17、-02-15 Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 Fraisures pour vis tte fraise avec une configuration de la tte conforme lISO 7721 ENISO15065:2005IS:56051 O5002(E) DPlcsid Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebod

18、s licensilop gnic,y this file mairp eb ynted iv roweb detu slahl ton ide ebtlnu deess the typefaces whice era hml era deddebicsnede to i dnanstlaled t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y

19、ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera Ai ebods a tredamafo kr Aebod SystemI sncotaropr.de teDails fo teh softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer

20、neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem leratit gno it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ISO 5002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb

21、y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mecinahcal, inclidung tohpcoiypodna gn micrfoilm, wittuoh repmissii non writign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotrfo y ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4

22、 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mail coirypthgiso.o gr We bwww.is.o gro Pulbisdehi n Switlrez dnaii ISO 5002 Allr ithgsr esedevrENISO15065:2005IS:56051 O5002(E) I SO 5002 All irthgs ersedevr iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of n

23、ational standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Inter

24、national organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the

25、 rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by

26、 at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15065 was prepared by Technical Committee ISO

27、/TC 2, Fasteners, Subcommittee SC 7, Reference Standards for fasteners (mainly covering terminology, dimensioning, sizes and tolerancing). ENISO15065:2005blank ENISO15065:2005INTENRATIONAL TSANDADR IS:56051 O5002(E)I SO 5002 All irthgs ersedevr 1Countersinks for countersunk head screws with head con

28、figuration in accordance with ISO 7721 1 Scope This International Standard specifies the dimensions and designation of countersinks for countersunk head screws with a head configuration in accordance with ISO 7721. This International Standard is applicable to the following types of screws: slotted c

29、ountersunk flat head screws according to ISO 2009; slotted countersunk raised head screws according to ISO 2010; slotted countersunk flat head tapping screws according to ISO 1482; slotted countersunk raised head tapping screws according to ISO 1483; cross-recessed countersunk flat head screws accor

30、ding to ISO 7046-1 and ISO 7046-2; cross-recessed countersunk raised head screws according to ISO 7047; cross-recessed countersunk flat head tapping screws according to ISO 7050; cross-recessed countersunk raised head tapping screws according to ISO 7051; cross-recessed countersunk flat head drillin

31、g screws according to ISO 15482; cross-recessed countersunk raised head drilling screws according to ISO 15483; hexalobular socket countersunk raised head screws according to ISO 14584; hexalobular socket countersunk flat head tapping screws according to ISO 14586; hexalobular socket countersunk rai

32、sed head tapping screws according to ISO 14587. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any

33、 amendments) applies. ISO 273:1979, Fasteners Clearance holes for bolts and screws ISO 7721:1983, Countersunk head screws Head configuration and gauging ENISO15065:2005IS:56051 O5002(E) 2 I SO 5002 All irthgs ersedevr3 Dimensions The dimensions of the countersink shall be as specified in Figure 1 an

34、d Table 1. Figure 1 Dimensions Table 1 Dimensions of countersink Dimensions in millimetres d h aD ct Nominal size Thread size min. (nom.) max. min. (nom.) max. 1,6 M1,6 1,80 1,94 3,6 3,7 0,95 2 M2 ST2,2 2,40 2,54 4,4 4,5 1,05 2,5 M2,5 2,90 3,04 5,5 5,6 1,35 3 M3 ST2,9 3,40 3,58 6,3 6,5 1,55 3,5 M3,5

35、 ST3,5 3,90 4,08 8,2 8,4 2,25 4 M4 ST4,2 4,50 4,68 9,4 9,6 2,55 5 M5 ST4,8 5,50 5,68 10,40 10,65 2,58 5,5 ST5,5 6,00 b6,18 11,50 11,75 2,88 6 M6 ST6,3 6,60 6,82 12,60 12,85 3,13 8 M8 ST8 9,00 9,22 17,30 17,55 4,28 10 M10 ST9,5 11,00 11,27 20,0 20,3 4,65 aClearance hole according to ISO 273, medium s

36、eries, tolerance H13. bNot specified in ISO 273. ENISO15065:2005IS:56051 O5002(E) I SO 5002 All irthgs ersedevr 34 Designation Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 shall be designated by reference to this International Standard and the nominal

37、size. EXAMPLE A countersink for countersunk head screws with head configuration according to ISO 7721 and with metric screw thread M4 or with tapping screw thread ST4,2 (nominal size 4) is designated as follows: Countersink ISO 15065 - 4 5 Representation in drawings In technical drawings, the repres

38、entation of countersinks shall be as shown in Figure 2. Figure 2 Representation ENISO15065:2005IS:56051 O5002(E) 4 I SO 5002 All irthgs ersedevrBibliography 1 ISO 1482, Slotted countersunk (flat) head tapping screws (common head style) 2 ISO 1483, Slotted raised countersunk (oval) head tapping screw

39、s (common head style) 3 ISO 2009, Slotted countersunk flat head screws (common head style) Product grade A 4 ISO 2010, Countersunk slotted raised head screws (common head style) Product grade A 5 ISO 7046-1, Countersunk flat head screws (common head style) with type H or type Z cross recess Product

40、grade A Part 1: Steel of property class 4.8 6 ISO 7046-2, Cross-recessed countersunk flat head screws (common head style) Grade A Part 2: Steel of property class 8.8, stainless steel and non-ferrous metals 7 ISO 7047, Countersunk raised head screws (common head style) with type H or type Z cross rec

41、ess Product grade A 8 ISO 7050, Cross recessed countersunk (flat) head tapping screws (common head style) 9 ISO 7051, Cross recessed raised countersunk (oval) head tapping screws 10 ISO 14584, Hexalobular socket raised countersunk head screws 11 ISO 14586, Hexalobular socket countersunk head tapping

42、 screws 12 ISO 14587, Hexalobular socket raised countersunk (oval) head tapping screws 13 ISO 15482, Cross recessed countersunk head drilling screws with tapping screw thread 14 ISO 15483, Cross recessed raised countersunk head drilling screws with tapping screw thread ENISO15065:2005blankBS EN ISO

43、15065:2005 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions Britis

44、h Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity whil

45、e using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscrib

46、ers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI

47、 website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European

48、 and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substan