BS EN ISO 13968-2008 Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility《塑料管路和管道系统 热塑管 环挠性测定》.pdf

《BS EN ISO 13968-2008 Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility《塑料管路和管道系统 热塑管 环挠性测定》.pdf》由会员分享，可在线阅读，更多相关《BS EN ISO 13968-2008 Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility《塑料管路和管道系统 热塑管 环挠性测定》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN ISO13968:2008ICS 23.040.20NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics piping andducting systems Thermoplastics pipes Determination ofring flexibility (ISO13968:2008)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncon

2、trolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June 2009 BSI 2009ISBN 978 0 580 56653 0Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 13968:2008National forewordThis British Standard is the UK implem

3、entation of EN ISO 13968:2008.It supersedes BS EN 1446:1996 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/4, Test methods.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not

4、 purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIEUROPEAN

5、 STANDARDNORME EUROPENNEEUROPISCHE NORMEN ISO 13968October 2008ICS 23.040.20 Supersedes EN 1446:1996 English VersionPlastics piping and ducting systems - Thermoplastics pipes -Determination of ring flexibility (ISO 13968:2008)Systmes de canalisations et de gaines en matiresplastiques - Tubes en mati

6、res thermoplastiques -Dtermination de la flexibilit annulaire (ISO 13968:2008)Kunststoff-Rohrleitungs- und Schutzrohrsysteme - Rohreaus Thermoplasten - Bestimmung der Ringflexibilitt (ISO13968:2008)This European Standard was approved by CEN on 14 October 2008.CEN members are bound to comply with the

7、 CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or

8、 to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versio

9、ns.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain,

10、 Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members

11、.Ref. No. EN ISO 13968:2008: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO 13968:2008EN ISO 13968:2008 (E) 3 Foreword This document (EN ISO 13968:2008) has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and va

12、lves for the transport of fluids“ in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo

13、rsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the latest by April 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identify

14、ing any or all such patent rights. This document supersedes EN 1446:1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Est

15、onia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 13968:2008 has been approved by CE

16、N as a EN ISO 13968:2008 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO 13968:2008ISO 13968:2008(E) ISO 2008 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide

17、 federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that

18、committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in acc

19、ordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requ

20、ires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13968 was prepared by Technic

21、al Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories Test methods and basic specifications. This second edition cancels and replaces the first edition (

22、ISO 13968:1997), which has been technically revised. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO 13968:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO 13968:2008INTERNATI

23、ONAL STANDARD ISO 13968:2008(E) ISO 2008 All rights reserved 1Plastics piping and ducting systems Thermoplastics pipes Determination of ring flexibility 1 Scope This International Standard specifies a method for testing the ring flexibility of a thermoplastics pipe having a circular cross-section. T

24、he method enables determination of the deflection, and necessary force, at which physical damage, if any, occurs within the specified diametric deflection. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the

25、 edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 9969, Thermoplastics pipes Determination of ring stiffness 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 r

26、ing flexibility ability of a pipe to resist ring diametric deflection without loss of structural integrity EN 13476-1:2007, 3.1.2.10 4 Principle The ring flexibility of a pipe is tested by measuring the force and the deflection while deflecting a ring section from the pipe diametrically at a constan

27、t speed until at least the specified deflection is achieved or prior fracture has occurred. Each test piece is monitored during testing and subsequently inspected for signs of several specific types of mechanical failure. NOTE It is assumed that the following test parameters are set by the standard

28、making reference to this International Standard: a) if appropriate, a greater length of the test pieces than the length specified in ISO 9969, see Clause 6; b) the deflection, if appropriate, see 8.1. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSI

29、BS EN ISO 13968:2008ISO 13968:2008(E) 2 ISO 2008 All rights reserved5 Apparatus 5.1 Compression testing machine, as specified in ISO 9969, but capable of producing at least the specified diametric deflection of the test piece at the applicable speed (see ISO 9969:2007, Table 1). 5.2 Dimensional and

30、force measuring devices, conforming to ISO 9969, but capable of measuring diametric deflections up to at least the specified deflection and the corresponding compressive forces. 6 Test pieces Prepare three test pieces from a single pipe, as specified in ISO 9969, and designate them a, b, and c respe

31、ctively. The referring standard may specify longer test pieces than defined in ISO 9969. 7 Conditioning Condition the test pieces as specified in ISO 9969. 8 Procedure 8.1 Conduct the test in accordance with the procedure given in ISO 9969, but continue compression while measuring the change in eith

32、er inside diameter or outside diameter until the specified deflection has been achieved. Unless otherwise specified in the referring standard, the deflection shall be 30 % of the outside diameter. During the compression, monitor for signs of failure (see 8.2), until either the specified deflection h

33、as been reached or the test piece has failed, whichever occurs first. If desired, the deflection may be continued after a failure has occurred or the specified deflection has been reached in order to determine other properties of the pipe. 8.2 For each test piece, prepare a force/deflection graph, a

34、nd inspect and record the type and the position of each event a) to e) with respect to the corresponding force and deflection. a) Inspect the force/deflection graph for compliance to the requirements in the referring standard. b) Check for any cracking or crazing in any part of the wall structure. c

35、) Check for any wall delamination. d) Check for any permanent buckling in any part of the structure of the pipe wall. e) Make any other observation as specified in the referring standard. Whitening of the pipe shall not be considered as an indication of one of the above-mentioned mechanical failures

36、. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO 13968:2008ISO 13968:2008(E) ISO 2008 All rights reserved 39 Test report The test report shall include at least the following information: a) a reference to this International Standard and t

37、o the referring standard; b) the identification of the thermoplastics pipe, including: 1) manufacturer, 2) type of pipe, 3) dimensions, 4) production date, 5) lengths of test pieces, 6) mass per metre length of the pipe; c) the test temperature; d) the force/deflection graph for each test piece; e)

38、where appropriate, the force and deflection at which any of the events specified in 8.2 occurred; f) the deflection and force at the maximum point, if a maximum occurred; g) any factors which may have affected the results, such as any incidents or any operating details not specified in this Internat

39、ional Standard; h) the date of test. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO 13968:2008ISO 13968:2008(E) 4 ISO 2008 All rights reservedBibliography 1 EN 13476-1:2007, Plastics piping systems for non-pressure underground drainage an

40、d sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: General requirements and performance characteristics Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO

41、13968:2008Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 01/09/2009 03:43, Uncontrolled Copy, (c) BSIBS EN ISO13968:2008BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body

42、 responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amen

43、dments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found

44、on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publ

45、ications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of t

46、hose that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services

47、are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. F

48、or detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/

49、.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise