BS EN 60679-3-2013 Quartz crystal controlled oscillators of assessed quality Standard outlines and lead connections《经质量评定的石英晶体振荡器 标准外形和引线连接》.pdf

《BS EN 60679-3-2013 Quartz crystal controlled oscillators of assessed quality Standard outlines and lead connections《经质量评定的石英晶体振荡器 标准外形和引线连接》.pdf》由会员分享，可在线阅读，更多相关《BS EN 60679-3-2013 Quartz crystal controlled oscillators of assessed quality Standard outlines and lead connections《经质量评定的石英晶体振荡器 标准外形和引线连接》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationQuartz crystal controlled oscillators of assessed qualityPart 3: Standard outlines and lead connectionsBS EN 60679-3:2013National forewordThis British Standard is the UK implementation of EN 60679-3:2013. It isidentical to IEC 60679-3:2012. It supersedes BS EN 60679-3:2002 w

2、hich iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/49, Piezoelectric devices for frequency control and selection.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include

3、 all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2013Published by BSI Standards Limited 2013ISBN 978 0 580 66748 0ICS 31.140Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Sta

4、ndard was published under the authority of theStandards Policy and Strategy Committee on 31 July 2013.Amendments issued since publicationAmd. No. Date Text affectedBRITISH STANDARDBS EN 60679-3:2013EUROPEAN STANDARD EN 60679-3 NORME EUROPENNE EUROPISCHE NORM July 2013 CENELEC European Committee for

5、Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref.

6、 No. EN 60679-3:2013 E ICS 31.140 Supersedes EN 60679-3:2001 English version Quartz crystal controlled oscillators of assessed quality - Part 3: Standard outlines and lead connections (IEC 60679-3:2012) Oscillateurs pilots par quartz sous assurance de la qualit - Partie 3: Encombrements normaliss et

7、 connexions des sorties (CEI 60679-3:2012) Quarzoszillatoren mit bewerteter Qualitt - Teil 3: Norm-Gehusemae und Anschlussdrhte (IEC 60679-3:2012) This European Standard was approved by CENELEC on 2013-01-18. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipula

8、te the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European

9、 Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC member

10、s are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norwa

11、y, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 60679-3:2013EN 60679-3:2013 - 2 - Foreword The text of document 49/1009/FDIS, future edition 3 of IEC 60679-3, prepared by IEC/TC 49 “Piezoelectric, dielectric and electrostatic devices

12、 and associated materials for frequency control, selection and detection“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60679-3:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical

13、 national standard or by endorsement (dop) 2014-01-12 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-01-18 This document supersedes EN 60679-3:2001. EN 60679-3:2013 includes the following significant technical changes with respect to EN 6067

14、9-3:2001: - CO 01, CO 07, CO 10, CO 17 and CO 18 were deleted; - the current pin layout of CO 06 was deleted; - new pin layout of CO 06 was added as CO 40; - new layout of CO 15 was added as CO 41; - two new enclosures, CO 42 and CO 43 were added. Therefore revised edition includes 15 types of enclo

15、sures as in Table 1 of Clause 5. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Stan

16、dard IEC 60679-3:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60679-1:2007 NOTE Harmonised as EN 60679-1:2007 (not modified). IEC 60679-4:1997 NOTE Harmon

17、ised as EN 60679-4:1998 (not modified). IEC 60679-4-1:1998 NOTE Harmonised as EN 60679-4-1:1998 (not modified). IEC 60679-5:1998 NOTE Harmonised as EN 60679-5:1998 (not modified). IEC 60679-5-1:1998 NOTE Harmonised as EN 60679-5-1:1998 (not modified). ISO 1101 NOTE Harmonised as EN ISO 1101. BS EN 6

18、0679-3:2013 2 60679-3 IEC:2012 CONTENTS 1 Scope . 5 2 Guidance for the standardization of outline drawings for frequency control and selection devices 5 3 Dimensions of crystal oscillator enclosure 7 4 Lead connections . 7 5 Designation of crystal oscillator enclosure 7 Annex A (normative) Lead conn

19、ections of crystal oscillators Type CO 02 to CO 43 23 Bibliography 25 Figure 1 Guidance for outline drawings 6 Table 1 Designation of crystal oscillator enclosures . 7 Table A.1 Lead connections of crystal oscillators Type CO 02 to CO 43 (1 of 2) . 23 BS EN 60679-3:201360679-3 IEC:2012 5 QUARTZ CRYS

20、TAL CONTROLLED OSCILLATORS OF ASSESSED QUALITY Part 3: Standard outlines and lead connections 1 Scope This part of IEC 60679 specifies the outline dimensions and lead connections for quartz crystal controlled oscillators with lead enclosures. 2 Guidance for the standardization of outline drawings fo

21、r frequency control and selection devices In order to achieve a uniform presentation of outline drawings for frequency control and selection devices, the following shall be considered. a) An outline drawing shall show all dimensional and geometrical characteristics of an enclosure necessary to ensur

22、e mechanical interchangeability with all other enclosures of the same outline. Enlarged and detailed view may be used, if necessary. b) The outline drawing shall consist of three parts: 1) A drawing with dimensional symbols (capital letter) as shown in Figure 1 with applicable footnotes, if necessar

23、y. 2) A tabular listing relating to the drawing symbol to the actual dimensions. Where possible, this shall be shown on the same page as the drawing. 3) An “actual-size“ sketch (scale 1:1). c) The outline drawing shall be executed in the third-angle projection. d) The function and identification of

24、the lead connections (termination) shall be determined by agreement between the supplier and user. They shall not be defined on the outline drawing. e) Descriptive footnotes may be used at the bottom of/ or adjacent to, the drawing with proper reference to the body of the drawing. f) All dimensions

25、shall be in millimeters. g) 0utline dimensions A, B, C, D and E shall be listed with maximum values only. h) If there are plural identical enclosures with different height (C), C shall be expressed with a suffix number such as C1, C2, etc. The following letter and number after the basic type number

26、(four digits) indicate the enclosure height and lead length. The identity references are given in the table in the sheet. i) Lead (termination) cross-sectional dimensions shall be listed with minimum and maximum values. If applicable, nominal dimensions may be added. j) The spacing of the leads (ter

27、mination) symbol H shall be listed with minimum, nominal and maximum dimensions. BS EN 60679-3:2013 6 60679-3 IEC:2012 E D C L H U W K A B Actual size IEC 2461/12 1 2 Figure 1 Guidance for outline drawings Scale 2:1 Sheet number Ref. Dimensions (mm) Footnotes Min. Nom. Max. A X B X C X D X E X H X X

28、 X K X X 1 L X X U X 2 W X 2 BS EN 60679-3:201360679-3 IEC:2012 7 k) Leads (terminations) for soldering application shall be specified with the minimum length dimensions (symbol L) only. Lead (termination) for plug-in application shall be specified with minimum and maximum length dimensions. l) If l

29、eads (terminations) are provided with an undercut, dimensions U and W shall be listed with minimum dimensions only. 3 Dimensions of crystal oscillator enclosure The dimensions in this standard apply to the completed quartz crystal controlled oscillators. Only those dimensions which meet the requirem

30、ents of the guidance for standardization of outline drawings are given (see Clause 2). 4 Lead connections Recommendations for the lead connections of quartz crystal controlled oscillators are given in Annex A to this standard. Lead connections shall always be given in the detail specification. 5 Des

31、ignation of crystal oscillator enclosure Table 1 Designation of crystal oscillator enclosures No. Type Sheet No. Description 1 CO 02 A1 CO 02 B1 Sheet 1 Metal enclosure, welded, 4 to 18 lead crystal oscillator outline 2 CO 05 B1 Sheet 2 Metal enclosure, welded, eight lead crystal oscillator outline

32、3 CO 08 A1 CO 08 B1 CO 08 C1 Sheet 3 Metal enclosure, five lead crystal oscillator outline 4 CO 09 A1 CO 09 B1 Sheet 4 Metal enclosure, five lead crystal oscillator outline 5 CO 15 B1 CO 15 C1 Sheet 5 Metal enclosure, five lead crystal oscillator outline 6 CO 16 A1 CO 16 B1 CO 16 C1 Sheet 6 Metal en

33、closure, four lead crystal oscillator outline 7 CO 19 A1 CO 19 B1 Sheet 7 Metal enclosure, five lead crystal oscillator outline 8 CO 21 A1 Sheet 8 Metal enclosure, welded, four lead crystal oscillator outline 9 CO 22 A1 Sheet 9 Plastic, moulded or ceramic, solder-glass sealed eight lead crystal osci

34、llator outline 10 CO 23 B1 Sheet 10 Metal enclosure, welded, eight lead crystal oscillator outline 11 CO 24 A1 Sheet 11 Metal enclosure, four lead crystal oscillator outline 12 CO 40 Sheet 12 Metal enclosure, five lead crystal oscillator outline 13 CO 41 A1 CO 41 B1 Sheet 13 Metal enclosure, four le

35、ad crystal oscillator outline 14 CO 42 Sheet 14 Metal enclosure, four lead crystal oscillator outline 15 CO 43 A1 CO 43 B1 CO 43 C1 Sheet 15 Metal enclosure, five lead crystal oscillator outline BS EN 60679-3:2013 8 60679-3 IEC:2012 Actual size B A M2H2(1) 1 14 7 8 (2) M118 17 19 20 15 16 21 22 K C

36、L N H3H3H1IEC 2462/12 Key (1) An indication shall be provided to locate the position of lead No.1 (a 90 corner is shown on the drawing as an example). (2) If required, insulating standoffs shall be located within corner areas defined in the table by M1 and M2. If insulating tape standoffs are used,

37、shaded areas as indicated are preferred and the tape may encircle the leads. 3 Leads with solderable finish shall not exceed Kmax. 4 Ground leads may be created by a brazed or welded joint(s) to the base. 5 The complete identity for any oscillator outline is a six digit type number consisting of the

38、 basic type number (four digits) followed by a letter indicating the enclosure height and a number indicating the lead length. The identity references are given in the table, where a dot indicates the missing information, which is given on another line. EXAMPLE CO 02 B1 is the complete identity for

39、the enclosure CO 02 with enclosure height C2and lead length L. Metal enclosure, welded, 4 to 18 lead crystal oscillator outline Type CO 02 Scale 2:1 Sheet 1 Ref. Dimensions (mm) Identity reference Footnotes Min. Nom. Max. A 20,70 B 13,10 C1 5,10 CO 02 A. 5 C2 6,60 CO 02 B. 5 H114,94 15,24 15,54 H27,

40、32 7,62 7,92 H32,30 2,54 2,70 K 0,40 0,53 3 L 5,85 CO 02 .1 5 M1 12,20 2 M2 4,58 2 N 0,75 BS EN 60679-3:201360679-3 IEC:2012 9 H Q P Actual size C L K A IEC 2463/12 1 Leads with solderable finish shall not exceed Kmax. 2 The complete identity for any oscillator outline is a six digit type number con

41、sisting of the basic type number (four digits) followed by a letter indicating the enclosure height and a number indicating the lead length. The identity references are given in the table, where a dot indicates the missing information, which is given on another line. EXAMPLE CO 05 B1 is the complete

42、 identity for the enclosure CO 05 with enclosure height C and lead length L. Metal enclosure, welded, eight lead crystal oscillator outline Type CO 05 Scale 2:1 Sheet 2 Ref. Dimensions (mm) Identity reference Footnotes Min. Nom. Max. A 13,20 C 8,90 CO 05 B. 2 H 6,70 7,10 7,50 K 0,40 0,53 1 L 11,70 C

43、O 05 .1 2 P 0,70 0,90 Q 0,60 0,80 BS EN 60679-3:2013 10 60679-3 IEC:2012 1 2 3 4 5 A H2B K C L H1IEC 2464/12 Ref. Dimensions (mm) Identity reference Footnotes Min. Nom. Max. A 36,10 B 27,20 C1 10,20 CO 08 A. 1 C2 12,80 CO 08 B. 1 C3 19,40 CO 08 C. 1 H125,25 25,40 25,65 H217,55 17,80 18,05 K 0,70 0,9

44、0 L 4,50 CO 08 .1 1 1 The complete identity for any oscillator outline is a six digit type number consisting of the basic type number (four digits) followed by a letter indicating the enclosure height and a number indicating the lead length. The identity references are given in the table, where a do

45、t indicates the missing information, which is given on another line. EXAMPLE CO 08 A1 is the complete identity for enclosure CO 08 with enclosure height C1 and lead length L. Metal enclosure, five lead crystal oscillator outline Type CO 08 Scale 1:1 Sheet 3 BS EN 60679-3:201360679-3 IEC:2012 11 1 2

46、3 4 5 A H1H2B K1C L K2H3IEC 2465/12 1 The complete identity for any oscillator outline is a six digit type number consisting of the basic type number (four digits) followed by a letter indicating the enclosure height and a number indicating the lead length. The identity references are given in the t

47、able, where a dot indicates the missing information, which is given on another line. EXAMPLE CO 09 A1 is the complete identity for enclosure CO 09 with enclosure height C1 and lead length L. Metal enclosure, five lead crystal oscillator outline Type CO 09 Scale 1:1 Sheet 4 Ref. Dimensions (mm) Ident

48、ity reference Footnotes Min. Nom. Max. A 36,10 B 27,20 C1 16,10 CO 09 A. 1 C2 19,40 CO 09 B. 1 H117,75 17,80 18,05 H220,15 20,35 20,55 H322,65 22,90 23,15 K10,70 0,90 K2 M2 L 4,50 CO 09 .1 1 BS EN 60679-3:2013 12 60679-3 IEC:2012 Actual size B 1 5 2 3 4 A H1H3H2K L C IEC 2466/12 1 The complete ident

49、ity for any oscillator outline is a six digit type number consisting of the basic type number (four digits) followed by a letter indicating the enclosure height and a number indicating the lead length. The identity references are given in the table, where a dot indicates the missing information, which is given on another l