BS EN 15090-2012 Footwear for firefighters《防火鞋》.pdf

《BS EN 15090-2012 Footwear for firefighters《防火鞋》.pdf》由会员分享，可在线阅读，更多相关《BS EN 15090-2012 Footwear for firefighters《防火鞋》.pdf（38页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 15090:2012Footwear for firefightersBS EN 15090:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 15090:2012. It supersedes BS EN 15

2、090:2006, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PH/1, Safety, protective and occupational footwear.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include

3、all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012 ISBN 978 0 580 67771 7 ICS 13.340.50 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the au

4、thority of the Standards Policy and Strategy Committee on 29 February 2012.Amendments issued since publicationDate Text affectedBS EN 15090:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15090 January 2012 ICS 13.340.50 Supersedes EN 15090:2006English Version Footwear for firefighters Chau

5、ssures pour pompiers Schuhe fr die Feuerwehr This European Standard was approved by CEN on 24 September 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alter

6、ation. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made

7、 by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estoni

8、a, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATIO

9、N EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15090:2012: EBS EN 15090:2012EN 15090:2012 (E) 2 Contents Page Foreword 4g3Introduction 5g31

10、g3 Scope 6g32g3 Normative references 6g33g3 Terms and definitions .6g34g3 Classification, design and type 6g34.1g3 Classification 6g34.2g3 Design .7g34.3g3 Type .7g35g3 Sampling and conditioning .7g36g3 Requirements .8g36.1g3 Types and classifications .8g36.2g3 General requirements 8g36.3g3 Thermal

11、behaviour 13g36.3.1g3 Insulation against heat . 13g36.3.2g3 Radiant heat 14g36.3.3g3 Flame resistance . 14g36.4g3 Compression resistance of the toepuff 14g36.5g3 Resistance to chemicals 15g36.6g3 Electrical properties . 15g36.6.1g3 General . 15g36.6.2g3 Electrically insulating footwear . 15g36.6.3g3

12、 Antistatic footwear 15g36.7g3 Outsole . 15g36.7.1g3 Cleat design . 15g36.7.2g3 Cleat height . 15g36.7.3g3 Cleat height in the waist area 15g36.7.4g3 Heel breast . 15g36.8g3 Zipper . 16g36.8.1g3 Zipper construction 16g36.8.2g3 Zipper (slide fastener) puller attachment strength 16g36.8.3g3 Zipper (sl

13、ide fastener) lateral strength . 16g37g3 Test methods . 16g37.1g3 Insulation against heat . 16g37.2g3 Radiant heat 16g37.3g3 Flame resistance test . 17g37.3.1g3 Conditioning and sampling . 17g37.3.2g3 Procedure 17g37.4g3 Compression resistance of the toepuff 18g37.5g3 Zipper . 19g37.5.1g3 Puller att

14、achment strength 19g37.5.2g3 Lateral strength . 19g38g3 Marking 20g39g3 Information to be supplied . 21g39.1g3 General . 21g39.2g3 Antistatic footwear 22g39.3g3 Insocks . 23g3BS EN 15090:2012EN 15090:2012 (E) 3 Annex A (informative) Example of guidelines and considerations for performing a risk . 24

15、g3A.1g3 General . 24g3A.2g3 General approach for conducting a risk assessment . 24g3A.3g3 Recommended factors for identifying and evaluating fire fighter risks 25g3A.4g3 Types of footwear for firefighters 26g3Annex B (normative) Assessment of the footwear by the laboratory during testing of thermal

16、behaviour 28g3B.1g3 General . 28g3B.2g3 Criteria for the assessment of the state of footwear . 28g3Annex C (informative) Assessment of the footwear by the wearer . 30g3C.1g3 General . 30g3C.2g3 Criteria for the assessment of the state of footwear . 30g3Annex ZA (informative) Relationship between thi

17、s European Standard and the Essential Requirements of EU Directive 89/686/EEC . 32g3Bibliography 34g3BS EN 15090:2012EN 15090:2012 (E) 4 Foreword This document (EN 15090:2012) has been prepared by Technical Committee CEN/TC 161 “Foot and leg protectors”, the secretariat of which is held by BSI. This

18、 European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the latest by July 2012. Attention is drawn to the possibility that some of the elem

19、ents of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 15090:2006. This document has been prepared under a mandate given to CEN by the European Commission and the European

20、Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. The main differences between this edition and EN 15090:2006 are as follows: a) Slip resistance has been added (

21、reference to EN ISO 20345, 5.3.5). b) The types of footwear for firefighters (4.3) have been changed in accordance with the risks. c) The requirements and the test method for radiant heat (6.3.2 and 7.2) have been changed. d) The requirement for resistance to chemicals (6.5) have been slightly chang

22、ed. e) The requirements for high electrical resistance outsoles (6.6.4 in the old version) and the adequate Marking symbols in Table 9 were removed. f) Annex B (normative) has been restructured. The criteria for the assessment of the state of footwear have been listed separately: “Insulation against

23、 heat”, “Radiant heat” and “Flame resistance”. g) Annex D Testing of laces has been deleted. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

24、Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 15090:2012EN 15090:2012 (E)

25、 5 Introduction The purpose of this standard is to provide minimum performance requirements and test methods for footwear for firefighters which is intended for use for fire fighting and associated activities. A risk assessment should be used to determine whether the footwear covered by this standar

26、d is suitable for the intended use for the expected exposure. Firefighters should be trained in the use, care and maintenance of the footwear covered by this standard, including an understanding of its limitations. BS EN 15090:2012EN 15090:2012 (E) 6 1 Scope This European standard specifies minimum

27、requirements and test methods for the performance of three types (see 4.3) of footwear for use by firefighters for fire suppression, general-purpose rescue, fire rescue and hazardous materials emergencies. This European standard does not cover special personal protective equipment used in high-risk

28、situations (for example, the conditions described in ISO 15538). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced docume

29、nt (including any amendments) applies. EN 13832-3:2006, Footwear protecting against chemicals Part 3: Requirements for footwear highly resistant to chemicals under laboratory conditions EN 50321, Electrically insulating footwear for working on low voltage installations EN ISO 6942:2002, Protective c

30、lothing Protection against heat and fire Method of test: Evaluation of materials and material assemblies when exposed to a source of radiant heat (ISO 6942:2002) EN ISO 15025:2002, Protective clothing Protection against heat and flame Method of test for limited flame spread (ISO 15025:2000) EN ISO 2

31、0344:2011, Personal protective equipment Test methods for footwear EN ISO 20345:2011, Personal protective equipment Safety footwear ISO 15538, Protective clothing for firefighters Laboratory test methods and performance requirements for protective clothing with a reflective outer surface 3 Terms and

32、 definitions For the purposes of this document, the terms and definitions given in EN ISO 20345:2011 apply. 4 Classification, design and type 4.1 Classification Footwear for firefighters shall be classified in accordance with Table 1. BS EN 15090:2012EN 15090:2012 (E) 7 Table 1 Classification of foo

33、twear Classification Description Class I Footwear made from leather and other materials, excluding all-rubber or all-polymeric footwear Class II All-rubber (i.e. entirely vulcanized) or all-polymeric (i.e. entirely moulded) footwear 4.2 Design Footwear shall conform to one of designs B to E of Figur

34、e 3 of EN ISO 20345:2011. 4.3 Type The types of footwear for firefighters shall be as follows: Type 1: Outdoor interventions, fire and wildland firefighting; no protection against penetration, no toe protection, no protection against chemical hazards; Type 2: All fire suppression and rescue interven

35、tions where protection against penetration, and toe protection are needed, no protection against chemical hazards; Type 3: All fire suppression and rescue interventions where protection against penetration and toe protection are needed, including protection against chemical hazards. 5 Sampling and c

36、onditioning The minimum number of samples shall be that specified in Clause 6 of EN ISO 20344:2011, together with the minimum number of test pieces taken from each sample, as given in Table 2. Wherever possible, test pieces shall be taken from the whole footwear unless otherwise stated in this stand

37、ard and in EN ISO 20344. If it is not possible to obtain a large enough test piece from the footwear, then a sample of the material from which the component has been manufactured may be used instead and this shall be noted in the test report. Where samples are required from each of three sizes, thes

38、e shall comprise the largest, smallest and a middle size of the footwear under test. All test pieces shall be conditioned in a standard atmosphere of (23 + 2) C and (50 + 5) % relative humidity for a minimum of 48 h before testing, unless otherwise stated in the test method. The maximum time which s

39、hall elapse between removal from the conditioning atmosphere and the start of testing shall be not greater than 10 min, unless otherwise stated in the test method. Each test piece shall individually satisfy the specific requirement, unless otherwise stated in the test method. NOTE The uncertainty of

40、 measurement for each test method described in the present standard may be assessed. One of the two following approaches should be used: a statistical method, e.g. that given in ISO 5725-2 20; BS EN 15090:2012EN 15090:2012 (E) 8 a mathematical method, e.g. that given in ENV 13005 3. Table 2 Minimum

41、number of samples and test specimens or test pieces Property to be determineda Reference Number ofsamples Number of test pieces from each sample Test only on the final footwear Radiant heat 6.3.2 1 pair See 7.2 Yes Flame 6.3.3 1 pair See 7.3 Yes Compression resistance of footwear forepart 6.4 1 pair

42、 from each of three sizes 1 pair Yes Zipper puller attachment strength 6.8.2 3 zippers No Zipper lateral strength 6.8.3 3 zippers No a Table 1 of EN ISO 20344:2011 applies. 6 Requirements 6.1 Types and classifications The permitted combinations of types of footwear for firefighters (see 4.3) and cla

43、sses I and II (see 4.1) shall be as given in Table 3. As specified in 4.2, design A shall not be used. Table 3 Relationship between types of footwear and classes Types of footwear Class I of Table 1 Class II of Table 1 1 Possible Possible 2 ossibl Possibl3 Not possible Possible NOTE Type 3 footwear

44、for firefighters are suitable for use with chemical protective clothing in accordance with EN 943-2, where appropriate. 6.2 General requirements Footwear for firefighters shall conform to the requirements specified in Table 4. BS EN 15090:2012EN 15090:2012 (E) 9 Table 4 General requirements Requirem

45、ents Reference Type 1 Type 2 Type 3 Marking symbol EN ISO 20345:2011 EN 15090 Class Class Class II I II I II General Footwear construction Type and classifications 4.1 and 6.1 X X X X X Height of upper 5.2.1 X X X X X Specific ergonomic features 5.3.4 X X X X X Leakproofness 5.3.3 N/A X N/A X X Wate

46、r resistance 6.2.5 X N/A X N/A N/A Seat region Design B Figure 3 of EN ISO 20345:2011 5.2.2 X X Design C and D Figure 3 of EN ISO 20345:2011 5.2.2 X X X X X Design E Figure 3 of EN ISO 20345:2011 5.2.2 N/A N/A N/A X X Whole footwear Sole performance Construction 5.3.1.1 X N/A X N/A N/A Upper/outsole

47、 bond strength 5.3.1.2 X N/A X N/A N/A Insulation against heat 6.3.1 X At least HI X At least HII X At least HI2 X At least HI2 X At least HI2Hl1 or Hl2 or Hl3 Slip resistance 5.3.5 X X X X X SRA SRB SRC Energy absorption of seat region 6.2.4 X X X X X BS EN 15090:2012EN 15090:2012 (E) 10 Flame resi

48、stance 6.3.3 X X X X X Penetration resistance 6.2.1 O O X X X P Toe protection General 5.3.2.1 O O X X X T (only for type 1) Internal length of toe caps 5.3.2.2 O O X X X Impact resistance 5.3.2.3 O O X X X Compression resistance 5.3.2.4 O O X X X Corrosion resistance of metallic toe caps 5.3.2.5.1

49、O O X X X Non-metallic toe caps 5.3.2.5.2 O O X X X Compression resistance of toe puff 6.4 * * N/A N/A N/A R Electrical properties Electrically insulating footwearg376 6.6.2 X X X X X See EN 50321 Antistatic footwear g376 6.6.3 A Resistance to imical environment Cold insulation of sole complex 6.2.3.2 * * * * * Cl Resistance to chemicals 6.5 N/A * N/A * X CH Accessories Zipper 6.8 O N/A O N/A N/A Metatarsal protection 6.2.6 * * * * * M Ankle protection 6.2.7 * * * * * AN Upper Thickness 5.4.2 N/A X N/A X X Tear strength 5.4.3 X N/A X