BS EN 14219-2003 Hexagon bolts with flange with metric fine pitch thread Small series《公制细牙螺纹六角法兰面螺栓 小型系列》.pdf

《BS EN 14219-2003 Hexagon bolts with flange with metric fine pitch thread Small series《公制细牙螺纹六角法兰面螺栓 小型系列》.pdf》由会员分享，可在线阅读，更多相关《BS EN 14219-2003 Hexagon bolts with flange with metric fine pitch thread Small series《公制细牙螺纹六角法兰面螺栓 小型系列》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 14219:2003 Incorporating corrigendum no. 1 Hexagon bolts with flange with metric fine pitch thread Small series The European Standard EN 14219:2003 has the status of a British Standard ICS 21.060.10 BS EN 14219:2003 This British Standard was published under the authority of th

2、e Standards Policy and Strategy Committee on 29 August 2003 BSI 2007 ISBN 0 580 42544 4 National foreword This British Standard was published by BSI. It is the UK implementation of EN 14219:2003, incorporating corrigendum February 2007. The UK participation in its preparation was entrusted to Techni

3、cal Committee FME/9, Bolts, nuts and accessories. A list of organizations represented on FME/9 can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a Br

4、itish Standard cannot confer immunity from legal obligations. WARNING The United Kingdom, as a member of CEN, is obliged to publish EN 14219:2003 as a British Standard. However, attention is drawn to the fact that during the development of the European Standard the United Kingdom consistently voted

5、against its approval as a European Standard. The UK believes that the corresponding International Standard, ISO 15072:1999, should have been implemented, without modification, as a European Standard. As far as the UK is concerned, it is dangerous and unacceptable to have a European Standard that dif

6、fers from the corresponding International Standard by the across flats dimension for one size of fastener, all other requirements being identical between the two standards concerned. As part of BSIs duty of care, we draw the attention of users of this standard to our concerns that M12 bolts conformi

7、ng to EN 14219 differ from similar fasteners conforming to ISO 15072 in the across flats dimension only. This is 16 mm in EN 14219 and 15 mm in ISO 15072. BSI will assume no liability whatsoever for the failure on the part of any user of this standard not to consider this aspect. Precautions are urg

8、ed to ensure that commingling of those M12 bolts which conform to EN 14219 and those M12 bolts which conform to ISO 15072 is avoided. Amendments issued since publication Amd. No. Date Comments 17056 Corrigendum No. 1 30 April 2007 Clause 3: Figure 2 replaced EUROPEAN STANDARD NORME EUROPENNE EUROPIS

9、CHE NORM EN 14219 April 2003 ICS 21.060.10 English version Hexagon bolts with flange with metric fine pitch thread Small series (ISO 15072:1999, modified) Vis tte hexagonale embase cylindro-trononique pas fin Srie troite (ISO 15072:1999, modifie) Sechskantschrauben mit Flansch mit Feingewinde Leicht

10、e Reihe (ISO 15072:1999, modifiziert) This European Standard was approved by CEN on 14 February 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U

11、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation unde

12、r the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Ital

13、y, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CEN All rights of exploitatio

14、n in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14219:2003 E Incorporating corrigendum February 2007EN 14219:2003 (E) 2 Foreword This document (EN 14219:2003) has been prepared by Technical Committee CEN/TC 185 “Threaded and non- threaded mechanical fasteners

15、and accessories“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latest by Octo

16、ber 2003. Annex A is normative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun- tries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,

17、Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 15072:1999 was approved by CEN as a European Standard with agreed common modifications as given below. Bolts in accordan

18、ce with this European Standard correspond to those specified in the International Standard ISO 15072:1999 with the exception that the width across flats for M12 is 16 mm (instead of 15 mm) and that the property class 9.8 was deleted. Moreover, the option for surface coatings according to ISO 10683 w

19、as added. EN 14219:2003 (E) 3 1 Scope This European Standard specifies the characteristics of hexagon bolts with flange with metric fine pitch thread, small series, with product grade A, with nominal thread diameters from 8 mm up to and including 16 mm and prop- erty classes 8.8, 10.9, 12.9 and A2-7

20、0. If, in special cases, specifications other than those listed in this European Standard are required, they shall be se- lected from existing European and International Standards, for example ISO 724, ISO 888, EN ISO 898-1, ISO 965-2, EN ISO 3506-1. 2 Normative references This European Standard inc

21、orporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this Eu

22、ropean Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 20225, Fasteners Bolts, screws, studs and nuts Symbols and designations of dimensions (ISO 225:1983). EN 26157-3, Fastene

23、rs Surface discontinuities Part 3: Bolts, screws and studs for special requirements (ISO 6157-3:1988). EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs (ISO 898-1:1999). EN ISO 3269, Fasteners Acceptance inspection (ISO 3269:2000).

24、 EN ISO 3506-1, Mechanical properties of corrosion-resistant stainless-steel fasteners Part 1: Bolts, screws and studs (ISO 3506-1:1997). EN ISO 4042, Fasteners Electroplated coatings (ISO 4042:1999). EN ISO 4753, Fasteners Ends of parts with external ISO metric screw thread (ISO 4753:1999). EN ISO

25、4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and C (ISO 4759-1:2000). EN ISO 10683, Fasteners Non-electrolytically applied zinc flake coatings (ISO 10683:2000). ISO 724, ISO general purpose metric screw threads Basic dimensions. ISO 965-2, ISO general pu

26、rpose metric screw threads Tolerances Part 2: Limits of sizes for general purpose external and internal screw threads Medium quality. ISO 8992, Fasteners General requirements for bolts, screws, studs and nuts. EN 14219:2003 (E) 4 3 Dimensions Dimensions shall be in accordance with Figures 1 to 4 and

27、 Table 1. Symbols and designations of dimensions are specified in EN 20225. Key aThe top of the head shall be either full form or indented at the manufacturers option and shall be either chamfered or rounded. The minimum diameter of the chamfer circle or start of rounding shall be equal to the maxim

28、um width across flats mnus 15 %. If the top of the head is indented, the periphery may be rounded. bEdge contour optional. cChamfered end (see EN ISO 4753). d = 15 to 30 ek w is the wrenching height; see the note to Table 1. fIncomplete thread u 2 P Figure 1 Hexagon bolt with flange Full shank (stan

29、dard type) Tolerances in millimetres NOTE For other dimensions, see Figure 1 Key aRounded or chamfered or conical. bd 2is approximately equal to the pitch diameter (rolling diameter). Figure 2 Hexagon bolt with flange Reduced shank, type R (upon request) EN 14219:2003 (E) 5 Type F without undercut (

30、upon request or optional) Type U with undercut (upon request or optional) Key ac is measured at d w min. b = 15 to 25 cMaximum and minimum underhead fillet. dJunction of fillet with bearing surface to be a smooth blend. Figure 3 Hexagon bolt with flange Underhead configuration (bearing area) Figure

31、4 Hexagon bolt with flange threaded to the head EN 14219:2003 (E) 6 Table 1 - Dimensions Dimensions in millimetres Thread d P aM8 1 M10 1 M10 1,25 M12 1,25 M12 1,5 (M14 1,5) bM16 1,5 max. 3 3 4,5 4,5 4,5a min. 1 1 1,5 1,5 1,5 c 22 26 30 34 38 d 28 32 36 40 44 b ref. e 57 c min. 1,2 1,5 1,8 2,1 2,4 F

32、 max. 9,2 11,2 13,7 15,7 17,7 d aTypes U max. 10 12,5 15,2 17,7 20,5 d cmax. 17 20,8 24,7 28,6 32,8 max. 8,00 10,00 12,00 14,00 16,00 d smin. 7,78 9,78 11,73 13,73 15,73 d vmax. 8,8 10,8 12,8 14,8 17,2 d wmin. 14,9 18,7 22,5 26,4 30,6 e min. 10,95 14,26 17,62 19,86 23,15 k max. 8,5 9,7 12,1 12,9 15,

33、2 k wmin. 3,8 4,3 5,4 5,6 6,8 l fmax. 2,1 2,1 2,1 2,1 3,2 r 1min. 0,4 0,4 0,6 0,6 0,6 r 2 fmax. 0,5 0,6 0,7 0,9 1 max. 0,36 0,45 0,54 0,63 0,72 r 3min. 0,16 0,20 0,24 0,28 0,32 r 4ref. 5,7 5,7 5,7 5,7 8,8 max. 10,00 13,00 16,00 18,00 21,00 s min. 9,78 12,73 15,73 17,73 20,67 max. 0,25 0,30 0,35 0,45

34、 0,50 v min. 0,10 0,15 0,15 0,20 0,25EN 14219:2003 (E) 7 Table 1 (continued) Dimensions in millimetres Thread d P aM8 1 M10 10 M10 1,25 M12 1,25 M 12 1,5 (M14 1,5) bM16 1,5 l g, hl sand l g i, jnom. min. max. l s min. l g max. l s min. l g max. l s min. l g max. l s min. l g max. l s min. l g max. 1

35、6 15,65 16,35 20 19,58 20,42 25 24,58 25,42 30 29,58 30,42 35 34,5 35,5 6,75 13 40 39,5 40,5 11,75 18 6,5 14 45 44,5 45,5 16,75 23 11,5 19 6,25 15 50 49,5 50,5 21,75 28 16,5 24 11,25 20 6 16 55 54,4 55,6 26,75 33 21,5 29 16,25 25 11 21 7 17 60 59,4 60,6 31,75 38 26,5 34 21,25 30 16 26 12 22 65 64,4

36、65,6 36,75 43 31,5 39 26,25 35 21 31 17 27 70 69,4 70,6 41,75 48 36,5 44 31,25 40 26 36 22 32 80 79,4 80,6 51,75 58 46,5 54 41,25 50 36 46 32 42 90 89,3 90,7 56,5 64 51,25 60 46 56 42 52 100 99,3 100,7 66,5 74 61,25 70 56 66 52 62 110 109,3 110,7 71,25 80 66 76 62 72 120 119,3 120,7 81,25 90 76 86 7

37、2 82 130 129,2 130,8 80 90 76 86 140 139,2 140,8 90 100 86 96 150 149,2 150,8 96 106 160 159,2 160,8 106 116 NOTE If the product passes the gauging in annex A, the requirements for dimensions c, e and k ware satisfied. a P is the pitch of the thread. b The size in parentheses should be avoided if po

38、ssible. c For lengths l nom 125 mm. dFor lengths 125 mm 200 mm. fRadius r 2 applies both at the corners and at the flats of the hexagon. gScrews with lengths shown above the thick stepped line are threaded to the head. hReduced shank type (type R) only below the dashed stepped line. il gis the minim

39、um grip length. jl g max = l nom b l s min = l g max 5 P (P is the pitch of the coarse thread with the corresponding diameter, specified in ISO 724ISO 261). EN 14219:2003 (E) 8 4 Specifications and reference European or International standards See Table 2. Table 2 Specifications and reference Europe

40、an and International standards Material Steel Stainless steel General requirements International Standard ISO 8992 Tolerance 6g Thread International Standards ISO 724, ISO 965-2 Property class 8.8, 10.9, 12.9 A2-70 Mechanical properties European Standards EN ISO 898-1 EN ISO 3506-1 Product grade A T

41、olerances European Standard EN ISO 4759-1 Finish as processed Requirements for electroplating are covered in EN ISO 4042. Requirements for non-electrolytically applied zinc flake coatings are covered in EN ISO 10683. Plain Surface discontinuities Limits for surface discontinuities are covered in EN

42、26157-3. Acceptability For acceptance procedure, see EN ISO 3269. 5 Designation EXAMPLE 1 A hexagon bolt with flange, small series, product grade A, with metric fine pitch thread M12 1,25, nominal length l = 80 mm, type F or U at the option of the manufacturer, and property class 8.8 shall be design

43、ated as follows: Hexagon bolt with flange EN 14219 M12 1,25 80 8.8 EXAMPLE 2 A hexagon bolt with flange, small series, product grade A, with metric fine pitch thread M12 1,25, nominal length l = 80 mm, type F, and property class 8.8 shall be designated as follows: Hexagon bolt with flange EN 14219 M

44、12 1,25 80 F 8.8 EXAMPLE 3 If, in special cases, a hexagon bolt with flange with reduced shank is required, the letter R shall be included in the designation: Hexagon bolt with flange EN 14219 M12 1,25 80 R 8.8 EN 14219:2003 (E) 9 Annex A (normative) Gauging of hexagon flange heads A.1 Recommended m

45、ethod for gauging of hexagon (see Figure A.1 and Table A.1) The head shall be gauged using two ring gauges, A and B, to demonstrate the coincidental acceptability of hexagon height, wrenching height, corner fill and width across corners. Gauge A shall be placed over the hexagon and shall seat on the

46、 flange. Gauge B shall be placed on the top of the head normal to the bolt axis. The two gauges shall not be in contact. A.2 Recommended method for gauging of flange thickness (see Figure A.1 and Table A.1) Gauge C is a flat feeler or ring gauge. It is used to prove that the flange thickness at the

47、junction with the hexagon portion is equal to or greater than specified values. The acceptance criterion is that gauge C shall fit under gauge A without contact when the bolt head is seated on a flat plate. Key 1 Gauge A 2 Gauge B 3 Gauge C NOTE W a, min = e theoretical W b, max= e min 0,01 mm T a,

48、max = k w, min Figure A.1 EN 14219:2003 (E) 10 Table A.1 Dimensions in millimetres Gauge A Gauge B Gauge C W aT aW bT bW cT cNominal thread diameter (d) max. min. max. min. max. min. min. max. max. min. 8 11,56 11,55 3,80 3,79 10,94 10,93 4 20 1,31 1,30 10 15,02 15,01 4,30 4,29 14,25 14,24 4 24 1,81 1,80 12 18,49 18,48 5,40 5,39 17,61 17,60 5 29 2,20 2,19 14 20,79 20,78 5,60 5,59 19,85 19,84 5 32,5 2,55 2,54 16 24,26 24,25 6,80 6,79 23,14 23,13 6 37 2,96 2,95