BS EN 10230-1-2000 Steel wire nails - Loose nails for general applications《钢圆铁钉 通用松动钉》.pdf

《BS EN 10230-1-2000 Steel wire nails - Loose nails for general applications《钢圆铁钉 通用松动钉》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10230-1-2000 Steel wire nails - Loose nails for general applications《钢圆铁钉 通用松动钉》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 10230-1:2000 The Eu

2、ropean Standard EN 10230-1:1999 has the status of a British Standard ICS 21.060.50; 77.140.65 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Steel wire nails Part 1: Loose nails for general applicationsThis British Standard, having been prepared under the direction of the Eng

3、ineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 BSI 01-2000 ISBN 0 580 35464 4 BS EN 10230-1:2000 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard is the English languag

4、e version of EN 10230-1:1999. The UK participation in its preparation was entrusted to Technical Committee ISE/26, Steel wire, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for ch

5、ange, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or

6、European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the

7、necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page

8、, pages 2 to 25 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.(8523($167$1$5 1250(8523e(11( (8523b,6 b) type of nail; c) nominal characteristic dimension; d) length; e) type and surface of head; f) type of shank; g) type of point; h

9、) surface coatings. Unless otherwise specified, nails with flat smooth circular heads, plain shanks and diamond points shall be supplied.Page 11 EN 10230-1:1999 BSI 01-2000 6 Requirements 6.1 Materials and manufacture Nails shall be produced from wire drawn from rods produced in accordance with EN 1

10、0016 Parts 1 to 4. Nails produced in accordance with this European Standard shall not be subjected to heat treatment after fabrication except for that incurred during surface coating. Where heat treatment is applied after fabrication the purchaser shall be informed. 6.2 Surface coating The surface o

11、f the wire nails shall comply with one of the following: a) Uncoated. The surface of the nails shall be free from rust; b) Zinc coated or zinc alloy coated, with a minimum zinc purity of 98,5 % in the outer surface of the coating, by one of the following alternatives: 1) Hot dipped to provide a mini

12、mum coating of 300 g/m 2 at an Acceptable Quality Level (AQL) of 10 %; 2) Barrel coated to provide a minimum coating of 300 g/m 2at an AQL of 10 % of nails with nominal characteristic dimensions greater than 2.6 mm; 3) Electroplated zinc coatings in accordance with ISO 2081; 4) Other zinc or zinc al

13、loy coating methods such as sheradizing or mechanical zinc plating as agreed between purchaser and supplier. c) Lacquered, cement coated or phosphate coated. 6.3 Form and dimensions The form and preferred dimensions are given in tables 1 to 12. NOTE Other lengths having incremental steps usually of

14、5 mm are possible subject to agreement between purchaser and supplier. 6.3.1 Nail point The following types of nail points shall be used: diamond point; diamond point offset; round point; chisel point; cut point. 6.3.2 Nail shank The following forms of nail shank shall be used: plain shank; indented

15、 shank;Page 12 EN 10230-1:1999 BSI 01-2000 spiral rolled shank; ring rolled shank; twisted shank; grooved shank. The cross-section of nail Tables 1 to 12. Nominal nail characteristic dimensions for indented, spiral rolled and ring rolled shanks are as for plain shank. 6.3.3 Nail head The top surface

16、 of the nail head shall be smooth or chequered. NOTE The top surface of the head may be marked by using raised or sunken letters, signs or numbers. The following types of head shall be used: circular flat head; countersunk head; lost round head; lost oval head; brad oval head; flat countersunk; cup

17、head; spring head; washer head; clout head 7 Tolerances 7.1 Length, l The tolerance on the nail length shall be 0,5 d. 7.2 Nominal characteristic dimension, d The tolerance on the nominal characteristic dimension applies to the nail shank before coating. The nominal characteristic dimension toleranc

18、es on nails shall be T1 of EN 102182. 7.3 Head diameter, d h The tolerance on the head diameter of nails shall be 0,05 d hwith a minimum of 0,2 mm.Page 13 EN 10230-1:1999 BSI 01-2000 8 Sampling and testing The manufacturer, is responsible for the control of product quality by the application of stat

19、istical methods of sampling and analysis of results with AQL values as agreed between purchaser and supplier. When required by the purchaser the coating weight of nails shall be tested in accordance with the gravimetric method in prEN 10244-1 and prEN 10244-2. The total area shall be taken as (total

20、 shank area + 2 (head area). 9 Inspection and documentation Unless otherwise agreed at the time of the order, non specific testing and inspection documentation shall be provided according to the requirements of EN 10021 and EN 10204. 10 Packaging and labelling Nails are usually supplied packaged in

21、cartons by net weight or by an approximate number of nails. The label or text on the package shall give the following: number of this European Standard i.e. EN 10230-1; type; length and nominal characteristic dimension; surface coating; weight or approximate number of nails; manufacturer.Page 14 EN

22、10230-1:1999 BSI 01-2000 Table 1 Dimensions for circular, flat, flat countersunk and cup head, plain shank nails Dimensions in mm Nominal 1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,7 3,0 3,4 3,8 4,2 4,6 5,0 5,5 6,0 7,0 8,0 characteristic dimension D Nail 10 Length 15 L 20 25 25 30 30 30 30 30 40 40 45 40 40

23、40 50 50 50 50 60 60 60 70 70 70 80 80 80 90 90 90 90 100 100 100 100 110 120 120 140 140 150 160 180 200 280 Head 2.8 3.3 3.9 4.0 4.5 5 ,0 5.5 5.9 6.1 6.8 7.7 7.6 8.4 9.2 10 11 12 14 16 diameter d hPage 15 EN 10230-1:1999 BSI 01-2000 Table 2 Dimensions for circular, flat and flat countersunk head,

24、grooved shank nails Dimensions in mm Nominal 1,4 1,6 1,8 2,0 2,2 2,4 2,7 3,0 3,4 3,8 4,2 4,6 5,0 5,5 6,0 7,0 8,0 characteristic dimension D Nail 20 Length 25 L 30 30 30 35 35 40 40 40 50 50 50 60 60 60 60 60 70 70 70 70 80 80 80 80 90 90 90 90 90 100 100 100 100 100 110 110 120 120 120 120 130 140 1

25、40 140 150 150 160 170 180 200 200 220 250 280 300 Head 3,2 3,6 4,0 4,5 5,0 5,5 5,9 6,8 7,7 7,7 8,4 9,2 10 11 12 14 16 diameter d hPage 16 EN 10230-1:1999 BSI 01-2000 Table 3 Dimensions for circular, flat and flat countersunk head, square shank nails Dimensions in mm Nominal 1,0 1,2 1,4 1,6 1,7 1,8

26、2,0 2,2 2,5 2,8 3,1 3,4 3,8 4,2 4,6 4,8 5,5 6,0 7,0 characteristic dimension d Nail 15 20 25 25 30 35 40 45 55 65 80 90 100 125 130 150 160 180 210 length 35 35 35 40 50 50 60 75 95 125 175 190 260 l 40 55 65 90 100 200 Head 2,5 3,0 3,5 4,0 4,3 4,5 5,0 5,5 6,3 7,0 7,8 8,5 9,5 10,5 11,5 12,0 13,8 15,

27、0 17,5 diameter d hPage 17 EN 10230-1:1999 BSI 01-2000 Table 4 Dimensions for lost round head, plain shank nails Dimensions in mm Nominal 1,0 1,2 1,4 1,6 1,8 2,0 2,2 2,4 2,7 3,0 3,4 3,8 4,2 4,6 5,0 characteristic dimension d Nail length 10 l 15 20 25 25 30 30 30 30 30 40 40 45 40 40 40 50 50 50 50 6

28、0 60 60 70 70 70 80 80 80 90 90 90 90 100 100 100 100 110 120 120 140 Head 1,4 1,7 2,0 2,2 2,5 2,8 3,1 3,4 3,8 4,2 4,8 5,3 5,9 6,4 7,0 diameter d hPage 18 EN 10230-1:1999 BSI 01-2000 Table 5 Dimensions for lost round head, grooved shank nails Dimensions in mm Nominal 1,4 1,6 1,8 2,0 2,2 2,4 2,7 3,0

29、3,4 3,8 4,2 4,6 5,0 characteristic dimension d Nail length 20 l 25 30 30 30 35 35 40 40 40 50 50 50 60 60 60 60 60 70 70 70 70 80 80 80 80 90 90 90 90 90 100 100 100 100 100 110 110 120 120 120 120 130 140 140 150 Head 2,0 2,2 2,5 2,8 3,1 3,4 3,8 4,2 4,8 5,3 5,9 6,4 7,0 diameter d hPage 19 EN 10230-

30、1:1999 BSI 01-2000 Table 6 Dimensions for lost round head, plain shank nails Dimensions in mm Nominal hti t i1,0 1,2 1,4 1,6 1,7 1,8 2,0 2,2 2,5 2,8 3,1 3,4 3.8 4,2 dimension d Nail length 15 20 25 25 30 35 40 45 55 65 80 90 100 125 l 35 35 35 40 50 50 60 75 95 125 40 55 65 90 100 Head 2,5 3,0 3,5 4

31、,0 4,3 4,5 5,0 5,5 6,3 7,0 7,8 8,5 9,5 10,5 diameter d hPage 20 EN 10230-1:1999 BSI 01-2000 Table 7 Dimensions for clout head, plain shank nails Dimensions in mm Nominal characteristic dimension 2,2 2,4 2,7 3,0 3,4 3,8 4,6 d Nail length 20 25 20 l 30 25 25 30 30 30 40 35 40 40 40 40 45 45 50 50 50 50 50 65 65 75 100 Head diameter 7,3 7,9 8,9 9,9 11,2 11,8 13,1 d h