BS EN 10079-2007 Definition of steel products《钢产品定义》.pdf

《BS EN 10079-2007 Definition of steel products《钢产品定义》.pdf》由会员分享，可在线阅读，更多相关《BS EN 10079-2007 Definition of steel products《钢产品定义》.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58The European Standard EN 10079:2007 has the status of a British StandardICS 01.040.77; 77.140.01Def

2、inition of steel productsBRITISH STANDARDBS EN 10079:2007BS EN 10079:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2007 BSI 2007ISBN 978 0 580 50483 9Amendments issued since publicationAmd. No. Date Commentscontract. Users are

3、responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. National forewordThis British Standard was published by BSI. It is the UK implementation of EN 10079:2007. It supersedes BS EN 10079:1993 which is withdrawn.The UK participation

4、in its preparation was entrusted to Technical Committee ISE/5, Technical delivery conditions, classification and designation of steels.A list of organizations represented on ISE/5 can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of

5、 a EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10079March 2007ICS 01.040.77; 77.140.01 Supersedes EN 10079:1992 English VersionDefinition of steel productsDfinition des produits en acier Begriffsbestimmungen fr StahlerzeugnisseThis European Standard was approved by CEN on 13 January 2007.CEN m

6、embers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on applicat

7、ion to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has th

8、e same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,

9、Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reserve

10、dworldwide for CEN national Members.Ref. No. EN 10079:2007: EEN 10079:2007 (E) 2 Contents Page Foreword3 Introduction .4 1 Scope 5 2 Normative references 5 3 Terms and definitions .8 Annex A (normative) Steel products and associated standards .29 Annex B (informative) Notes on the former European Co

11、al and Steel Community (ECSC) definitions and Harmonised Commodity Description and Coding System (HS) definitions.33 B.1 European Coal and Steel Community (ECSC) definitions.33 B.2 Harmonized Commodity Description and Coding System definitions 34 Annex C (informative) Trilingual vocabulary .36 Bibli

12、ography 44 EN 10079:2007 (E) 3 Foreword This document (EN 10079:2007) has been prepared by Technical Committee ECISS/TC 6 “Definition and classification”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an ide

13、ntical text or by endorsement, at the latest by September 2007, and conflicting national standards shall be withdrawn at the latest by September 2007. This document supersedes EN 10079:1992. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun

14、tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa

15、in, Sweden, Switzerland and United Kingdom. EN 10079:2007 (E) 4 Introduction There are various classification systems existing in Europe but this European Standard only deals with definitions for steel products manufactured by or used in the steel industry or by its customers. For example, Annex B p

16、rovides guidance on the definition systems used in the former European Coal and Steel Community (ECSC) Treaty as well as the Statistical office of the European Communities and of the Harmonised Commodity Description and Coding System. The entries that are presented in this European Standard have bee

17、n ordered systematically, and have been grouped by steel products according to: shape and dimensions e.g. flat products, long products, heavy sections; appearance and surface condition e.g. coated flat products, bright products. This European Standard also contains an alphabetical index, which has b

18、een included at the end of this document. EN 10079:2007 (E) 5 1 Scope This European Standard defines terms for steel products according to: a) shape and dimensions; and b) appearance and surface condition. NOTE 1 Although the products are generally defined independently of their end uses or manufact

19、uring processes, it has sometimes been necessary to make reference to these criteria. NOTE 2 All dimensions given in this European Standard are nominal. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the ed

20、ition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 39, Loose steel tubes for tube and coupler scaffolds Technical delivery conditions EN 10017, Steel rod for drawing and/or cold rolling Dimensions and tolerances EN 10024,

21、 Hot rolled taper flange I sections Tolerances on shape and dimensions EN 10029, Hot rolled steel plates 3 mm thick or above Tolerances on dimensions, shape and mass EN 10034, Structural steel I and H sections Tolerances on shape and dimensions EN 10048, Hot rolled narrow steel strip Tolerances on d

22、imensions and shape EN 10051:1991 + A1:1997, Continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Tolerances on dimensions and shape (includes amendment A1:1997) EN 10055, Hot rolled steel equal flange tees with radiused root and toes Dimensions and tolerances on s

23、hape and dimension EN 10056-1, Structural steel equal and unequal leg angles Part 1: Dimensions EN 10058, Hot rolled flat steel bars for general purposes Dimensions and tolerances on shape and dimensions EN 10059, Hot rolled square steel bars for general purposes Dimensions and tolerances on shape a

24、nd dimensions EN 10060, Hot rolled round steel bars for general purposes Dimensions and tolerances on shape and dimensions EN 10061, Hot rolled hexagon steel bars for general purposes Dimensions and tolerances on shape and dimensions EN 10067, Hot rolled bulb flats Dimensions and tolerances on shape

25、, dimensions and mass EN 10080, Steel for the reinforcement of concrete Weldable reinforcing steel General EN 10079:2007 (E) 6 EN 10092-1, Hot rolled spring steel flat bars Part 1: Flat bars Dimensions and tolerances on shape and dimensions EN 10092-2, Hot rolled spring steel flat bars Part 2: Ribbe

26、d and grooved spring leaves Dimensions and tolerances on shape and dimensions EN 10106, Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state EN 10107, Grain-oriented electrical steel sheet and strip delivered in the fully processed state EN 10108, Round st

27、eel rod for cold heading and cold extrusion Dimensions and tolerances EN 10131: 2006, Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape prEN 10138-2, Prestressing steels Pa

28、rt 2: Wire prEN 10138-4, Prestressing steels Part 4: Bar EN 10140, Cold rolled narrow steel strip Tolerances on dimensions and shape EN 10143, Continuously hot-dip coated steel sheet and strip Tolerances on dimensions and shape EN 10162, Cold rolled steel sections Technical delivery conditions Dimen

29、sional and cross-sectional tolerances EN 10169-1, Continuously organic coated (coil coated) steel flat products Part 1: General information (definitions, materials, tolerances, test methods) EN 10202, Cold reduced tinmill products Electrolytic tinplate and electrolytic chromium/chromium oxide coated

30、 steel EN 10205, Cold reduced blackplate in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steel EN 10208-1, Steel pipes for pipelines for combustible fluids Technical delivery conditions Part 1: Pipes of requirement class A EN 10208-2, Steel pipes for pipeli

31、nes for combustible fluids Technical delivery conditions Part 2: Pipes of requirement class B EN 10210-2, Hot finished structural hollow sections of non-alloy and fine grain steels Part 2: Tolerances, dimensions and sectional properties EN 10216-1, Seamless steel tubes for pressure purposes Technica

32、l delivery conditions Part 1: Non-alloy steel tubes with specified room temperature properties EN 10216-2, Seamless steel tubes for pressure purposes Technical delivery conditions Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties EN 10216-3, Seamless steel tubes

33、for pressure purposes Technical delivery conditions Part 3: Alloy fine grain steel tubes EN 10216-4, Seamless steel tubes for pressure purposes Technical delivery conditions Part 4: Non-alloy and alloy steel tubes with specified low temperature properties EN 10216-5, Seamless steel tubes for pressur

34、e purposes Technical delivery conditions Part 5: Stainless steel tubes EN 10079:2007 (E) 7 EN 10217-1, Welded steel tubes for pressure purposes Technical delivery conditions Part 1: Non-alloy steel tubes with specified room temperature properties EN 10217-2, Welded steel tubes for pressure purposes

35、Technical delivery conditions Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties EN 10217-3, Welded steel tubes for pressure purposes Technical delivery conditions Part 3: Alloy fine grain steel tubes EN 10217-4, Welded steel tubes for pressure pur

36、poses Technical delivery conditions Part 4: Electric welded non-alloy steel tubes with specified low temperature properties EN 10217-5, Welded steel tubes for pressure purposes Technical delivery conditions Part 5: Submerged arc welded non-alloy and alloy steel tubes with specified elevated temperat

37、ure properties EN 10217-6, Welded steel tubes for pressure purposes Technical delivery conditions Part 6: Submerged arc welded non-alloy steel tubes with specified low temperature properties EN 10217-7, Welded steel tubes for pressure purposes Technical delivery conditions Part 7: Stainless steel tu

38、bes EN 10218-2, Steel wire and wire products General Part 2: Wire dimensions and tolerances EN 10219-2, Cold formed welded structural hollow sections of non-alloy and fine grain steels Part 2: Tolerances, dimensions and sectional properties EN 10220, Seamless and welded steel tubes Dimensions and ma

39、sses per unit length EN 10222-1, Steel forgings for pressure purposes Part 1: General requirements for open die forgings. EN 10224, Non-alloy steel tubes and fittings for the conveyance of aqueous liquids including water for human consumption - Technical delivery conditions EN 10248-2, Hot rolled sh

40、eet piling of non alloy steels Part 2: Tolerances on shape and dimensions EN 10249-2, Cold formed sheet piling of non alloy steels Part 2: Tolerances on shape and dimensions EN 10250-1, Open die steel forgings for general engineering purposes Part 1: General requirements EN 10255, Non-alloy steel tu

41、bes suitable for welding and threading Technical delivery conditions EN 10265, Magnetic materials Specification for steel sheet and strip with specified mechanical properties and magnetic permeability EN 10278, Dimensions and tolerances of bright steel products EN 10279, Hot rolled steel channels To

42、lerances on shape, dimension and mass EN 10294-1, Hollow bars for machining Technical delivery conditions Part 1: Non alloy and alloy steels EN 10296-1, Welded circular steel tubes for mechanical and general engineering purposes Technical delivery conditions Part 1: Non-alloy and alloy steel tubes E

43、N 10296-2, Welded circular steel tubes for mechanical and general engineering purposes Technical delivery conditions Part 2: Stainless steel EN 10297-1, Seamless circular steel tubes for mechanical and general engineering purposes Technical delivery conditions Part 1: Non-alloy and alloy steel tubes

44、 EN 10079:2007 (E) 8 EN 10297-2, Seamless circular steel tubes for mechanical and general engineering purposes Technical delivery conditions Part 2: Stainless steel tubes EN 10303, Thin magnetic steel sheet and strip for use at medium frequencies EN 10305-1, Steel tubes for precision applications Te

45、chnical delivery conditions Part 1: Seamless cold drawn tubes EN 10305-2, Steel tubes for precision applications Technical delivery conditions Part 2: Welded cold drawn tubes EN 10305-3, Steel tubes for precision applications Technical delivery conditions Part 3: Welded cold sized tubes EN 10305-4,

46、Steel tubes for precision applications Technical delivery conditions Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems EN 10305-5, Steel tubes for precision applications Technical delivery conditions Part 5: Welded and cold sized square and rectangular tubes EN 10305-6, Ste

47、el tubes for precision applications Technical delivery conditions Part 6: Welded cold drawn tubes for hydraulic and pneumatic power systems EN 10312, Welded stainless steel tubes for the conveyance of aqueous liquids including water for human consumption - Technical delivery conditions EN 10341, Col

48、d rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state EN ISO 1127, Stainless steel tubes Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) 3 Terms and definitions For the purposes of this document, the following terms and def

49、initions apply. 3.1 liquid steel 1)steel in the liquid state ready for pouring and obtained from the melting of raw materials 3.2 ingots and semi finished products 2)3.2.1 ingots products obtained by pouring liquid steel into moulds of a shape appropriate to the subsequent processing 3)into semi finished products, or flat or long products, generally by hot rol