BS 7900-1998 Specification for examination of the surface texture of precision steel castings《精加工钢铸件表面结构检验规范》.pdf

《BS 7900-1998 Specification for examination of the surface texture of precision steel castings《精加工钢铸件表面结构检验规范》.pdf》由会员分享，可在线阅读，更多相关《BS 7900-1998 Specification for examination of the surface texture of precision steel castings《精加工钢铸件表面结构检验规范》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS 7900 : 1998 ICS 77.140

2、.80 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Specification for Examination of the surface texture of precision steel castingsBS 7900 : 1998 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority

3、 of the Standards Board and comes into effect on 15 May 1998 BSI 1998 The following BSI references relate to the work on this standard: Committee reference ISE/6 Draft for comment 96/713267 DC ISBN 0 580 28932 X Amendments issued since publication Amd. No. Date Text affected Committees responsible f

4、or this British Standard The preparation of this British Standard was entrusted to Technical Committee ISE/6, Steel castings, upon which the following bodies were represented: BEAMA Ltd. British Pump Manufacturers Association British Valve and Actuator Manufacturers Association Castings Development

5、Centre Hopkinsons Limited Institute of British Foundrymen Lloyds Register of Shipping Ministry of Defence Railway Industry AssociationBS 7900 : 1998 BSI 1998 i Contents Page Committees responsible inside front cover Foreword ii Specification 1 Scope 1 2 Definitions 1 3 Description of tactile compara

6、tor set 1 4 Information to be supplied by the purchaser 1 5 Assessment of surface texture 2 6 Recording of results of examination 2 Annex A (informative) Examples of comparator plates 3ii BSI 1998 BS 7900 : 1998 Foreword This British Standard is aimed at facilitating a better understanding between t

7、he casting producer and purchaser regarding the natural surface finish produced by four precision casting processes. It is intended to prevent misunderstandings arising from imprecise descriptions at the enquiry and order stage and subsequent customer disappointment at the goods received stage. The

8、casting process characteristically produces randomly oriented irregularities on surfaces created by the moulding medium and subsequent fettling. These irregularities may be depressions or protrusions of widely varying shapes and sizes. The use of tactile comparators for the evaluation of surface qua

9、lity is superior to methods based on photographs which can introduce uncertainties concerning interpretation, particularly with regard to the profile of these surface irregularities. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This d

10、ocument comprises a front cover, an inside front cover, pages i and ii, pages 1 to 6, an inside back cover and a back cover. BSI 1998 1 BS 7900 : 1998 1) For information on the availability of comparators contact the BSI Information Centre, British Standards House, 389 Chiswick High Road, London W4

11、4AL. 2) An example of this is the Replicast process. Replicast is the trade-name of the Castings Development Centre. This information is given for the convenience of users of this standard and does not constitute an endorsement of the product named. Equivalent products may be used if they can be sho

12、wn to lead to the same results. Specification 1 Scope This British Standard specifies levels of surface roughness/texture on steel castings produced by the resin shell, lost wax, lost polystyrene and Shaw moulding processes (see 2.5 to 2.8 for a brief description of each process). Surfaces created b

13、y subsequent fettling operations (see 2.4) are also included. In addition to the definitive requirements, this standard also requires the items detailed in clause 4 to be documented. For compliance with this standard, both the definitive requirements and the documented items have to be satisfied. NO

14、TE. Acceptance levels should be agreed between the casting producer and purchaser by reference to a set of reference tactile comparators which represent the surfaces produced by the four moulding processes after blasting, and also, surfaces created by subsequent fettling operations. Annex A contains

15、 full size photographs of the comparator plates to assist in making a rapid review of the overall content of the set. It is emphasized, however, that the comparators and not the photographs should be used to form the basis of agreement 1) Agreement and acceptance is by visual examination and touch.

16、2 Definitions For the purpose of this standard, the following definitions apply. 2.1 surface texture The surface of the castings after blasting. 2.2 precision castings Castings exhibiting high external and internal integrity and exceptional dimensional accuracy. 2.3 tactile Relates to the sense of t

17、ouch. 2.4 fettling Removal of feeder heads and ingates by cutting and/or grinding operations. 2.5 resin shell process A precision moulding process that uses metal pattern and corebox equipment and resin-bonded sand. 2.6 lost polystyrene process 2) A precision moulding process that uses expanded poly

18、styrene patterns and thin ceramic shell moulds. 2.7 Shaw process A precision casting process that uses wooden/resin pattern and corebox equipment and ceramic block moulds. 2.8 lost-wax process A precision casting process that uses wax patterns and ceramic shell moulds. 3 Description of tactile compa

19、rator set The comparators are plastic replicas of actual cast steel surfaces. They comprise five categories, each with two or three levels of surface texture increasing in roughness from 1 to 2 or 3 (level 1 is the smoothest), as follows: resin shell process (three levels V1, V2, V3); lost polystyre

20、ne process (three levels W1, W2, W3); Shaw process (three levels X1, X2, X3); lost-wax process (two levels Y1, Y2); fettled surfaces (three levels Z1, Z2, Z3). Full size photographs of the comparators are shown in annex A for information purposes only. 4 Information and requirements to be agreed and

21、 documented The following information to be supplied by the purchaser shall be fully documented. Both the definitive requirements specified throughout the standard and the following documented items shall be satisfied before a claim of compliance with the standard can be made and verified: a) the ar

22、eas on the casting to be examined; b) whether the results of inspection are to be recorded; c) the acceptance category(ies) for each of the relevant areas on the casting.2 BSI 1998 BS 7900 : 1998 2) An example would be a 100 W bulb suspended approximately 1 metre above an object. 5 Assessment of sur

23、face texture 5.1 The following procedure shall form the basis of an assessment for a casting in the as supplied condition, prior to any coating operation. 5.2 The comparator, or comparators, used shall be representative of both the casting process and the surface acceptance criteria. 5.3 The compara

24、tor and casting surface shall be viewed together in lighting conditions of at least 350 lux 2) . 5.4 The assessment shall be satisfactory if, in the required area of the casting, the surface texture is equal to, or better than, the reference comparator selected in accordance with 6.3. NOTE. Difficul

25、ties may arise in accessing surfaces of castings covering a range of size and section thickness using standard comparators measuring 60 mm3 60 mm. It is emphasized, however, that it is not intended that areas of the casting should be divided up into areas of equivalent dimensions. 6 Recording of res

26、ults of examination The casting producer shall, if requested by the purchaser, keep a record of the examination and provide a report. The report shall contain the following information: a) casting identification; b) identification and authorization of the person undertaking the examination; c) compa

27、rator(s) used versus area of the casting examined; d) result determined as an actual level of roughness.BS 7900 : 1998 BSI 1998 3 Annex A (informative) Examples of comparator plates4 BSI 1998 BS 7900 : 1998 BSI 1998 5 BS 7900 : 1998BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | |

28、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body re

29、sponsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest am

30、endments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be

31、 found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publ

32、ications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards

33、 BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Cen

34、tre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7

35、001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tra

36、nsmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.