BS 7289-1990 Specification for dimensions of three-piece tinplate aerosol cans《三片式马口铁烟雾剂罐尺寸规范》.pdf

《BS 7289-1990 Specification for dimensions of three-piece tinplate aerosol cans《三片式马口铁烟雾剂罐尺寸规范》.pdf》由会员分享，可在线阅读，更多相关《BS 7289-1990 Specification for dimensions of three-piece tinplate aerosol cans《三片式马口铁烟雾剂罐尺寸规范》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS7289:1990 Specification for Dimensions of three-piece tinplate aerosol cansBS7289:1990 This British Standard, having been prepared under the directionof the Packaging and Freight Containers Standards Policy Committee, was publishedunder the authority ofthe Board ofBSI and comesint

2、oeffect on 30September1990 BSI11-1999 The following BSI references relate to the work on this standard: Committee reference PKM/562 Draft for comment89/39209 DC ISBN 0 580 18222 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Packaging

3、 and Freight Containers Standards Policy Committee (PKM/-) to Technical Committee PKM/562, upon which the following bodies were represented: Association of the British Pharmaceutical Industry British Aerosol Manufacturers Association British Compressed Gases Association British Pest Control Associat

4、ion British Plastics Federation Camping and Outdoor Leisure Association Consumer Policy Committee of BSI Cosmetic, Toiletry and Perfumery Association Ltd. Department of Trade and Industry (Consumer Safety Unit, CA Division) Health and Safety Executive Institute of Trading Standards Administration Li

5、quefied Petroleum Gas Industry Technical Association (UK) Metal Packaging Manufacturers Association PIRA Society of Cosmetic Scientists Amendments issued since publication Amd. No. Date CommentsBS7289:1990 BSI 11-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2

6、Definitions 1 3 Dimensions and tolerances 1 Figure 1 Dimensions of cylindrical straight-sided three-piece aerosolcans,with tolerances 3 Figure 2 Dimensions of necked-in three-piece aerosol cans, with tolerances 5 Figure 3 Measurement of the contact height 6 Table 1 Dimensions of cylindrical straight

7、-sided three-piece aerosol cans 2 Table 2 Dimensions of necked-in three-piece aerosol cans 4 Publication(s) referred to Inside back coverBS7289:1990 ii BSI 11-1999 Foreword This British Standard has been prepared under the direction of the Packaging and Freight Containers Standards Policy Committee

8、at the request of the Metal Packaging Manufacturers Association, supported by the British Aerosol Manufacturers Association. This British Standard specifies only the dimensions of three-piece aerosol cans. Constructional and performance requirements are specified in BS3914 which also includes requir

9、ements relating to the complete, filled aerosol dispenser. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from l

10、egal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, pages1 to6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment tabl

11、e on the inside front cover.BS7289:1990 BSI 11-1999 1 1 Scope This BritishStandard specifies dimensions of both cylindrical straight-sided and necked-in three-piece tinplate aerosol cans, in a listed range of nominal capacities from140mL to1000mL. NOTEThe titles of the publications referred to in th

12、is standard are listed on the inside back cover. 2 Definitions For the purposes of this BritishStandard the definitions given in BS6966-3 apply together with the following. 2.1 contact height the dimension, used for the adjustment of the clinching tool, which determines the point at which the valve

13、mounting cup seals against the curl of the aerosol can 2.2 curl the radiused edge of the aperture of the aerosol can 3 Dimensions and tolerances 3.1 Cylindrical straight-sided cans The dimensions shall be as given in Table 1 and shown in Figure 1. The limits of tolerance shall be as shown in Figure

14、1. NOTECylindrical straight-sided aerosol cans of65mm diameter may be fitted with either low or high profile top ends. Dimensions for both types are given in Table 1. 3.2 Necked-in cans The dimensions shall be as given in Table 2 and shown in Figure 2. The limits of tolerance shall be as shown in Fi

15、gure 2. 3.3 Measurement of dimensions 3.3.1 Diameters and heights Diameters and heights, other than those related to the aperture, shall be determined as described in BS6966-3. 3.3.2 Dimensions related to the aperture 3.3.2.1 Diameters The outside diameter of the curl shall be measured at three poin

16、ts, at60 intervals around the circumference and the arithmetic mean of the three values shall be used to check compliance. The internal diameter shall be similarly measured at three points and the arithmetic mean used to check compliance. 3.3.2.2 Contact height The contact height shall be measured a

17、t three equidistant points around the circumference of the aperture using a suitable measuring gauge 1) . The points of reference for the measurement are two datum lines, one horizontal in the plane of the top of the curl and the other vertical and tangential to the curl profile (see Figure 3). The

18、measuring gauge shall be so designed that when the main body of the gauge is aligned with the horizontal datum line, a ball of1.5mm radius is maintained in an accurately fixed relationship to the vertical datum line, i.e.offset by0.35mm (seeFigure 3). The ball shall be lightly spring loaded so that

19、it maintains contact with the underside of the curl when the gauge is in position. The measuring gauge shall have a means of registering the distance from the centre of the ball to the horizontal datum line, i.e.the contact height. 1) For information on the availability of suitable measuring gauges

20、apply to Enquiry Section, BSI, Linford Wood, Milton Keynes MK146LE enclosing a stamped addressed envelope for reply.BS7289:1990 2 BSI 11-1999 Table 1 Dimensions of cylindrical straight-sided three-piece aerosol cans Nominal brimful capacity a Nominal dimensions Dimensions c Diameter D i b Body heigh

21、t H 1 Height H 2 Height H 3 Height H 4 Diameter D 1 Diameter D 4 Dimension C Low profile High profile Low profile High profile mL 140 175 210 225 270 290 335 395 405 450 360 395 405 510 520 600 650 800 1000 mm 52 52 52 52 52 52 52 52 52 52 65 65 65 65 65 65 65 65 65 mm 72 88 105 111 132 141 161 190

22、195 209 107 118 122 154 157 181 195 240 300 mm 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 15.5 15.5 15.5 15.5 15.5 15.5 15.5 15.5 15.5 mm 20.3 20.3 20.3 20.3 20.3 20.3 20.3 20.3 20.3 mm 81.5 97.5 114.5 120.5 141.5 150.5 170.5 199.5 204.5 218.5 122.5 133.5 137.5 169.5 172.5 196.5 210.5 255.5 315.5 mm 12

23、7.3 138.3 142.3 164.3 177.3 201.3 215.3 260.3 320.3 mm 65 81 98 104 125 134 154 183 188 202 100 111 115 147 150 174 188 233 293 mm 55.5 55.5 55.5 55.5 55.5 55.5 55.5 55.5 55.5 55.5 68.7 68.7 68.7 68.7 68.7 68.7 68.7 68.7 68.7 mm 45.4 45.4 45.4 45.4 45.4 45.4 45.4 45.4 45.4 45.4 58.5 58.5 58.5 58.5 5

24、8.5 58.5 58.5 58.5 58.5 mm 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 a For product fill volumes reference should be made to BS3914. b Refers to internal diameter (see BS6966-3). c Tolerances are shown in Figure 1.BS7289:1990 BSI 11-1999 3 Figure 1 Dimensions of cyli

25、ndrical, straight-sided three-piece aerosol cans, with tolerancesBS7289:1990 4 BSI 11-1999 Table 2 Dimensions of necked-in three-piece aerosol cans Nominal brimful capacity a Nominal dimensions Dimensions Diameter D i b Diameter DN 1 Diameter DN 2 Body height H 1 Height H 2 Height H 3 Diameter D 1 D

26、imension C Dimension H 5 Diameter D 2 mL 140 175 210 240 250 270 210 240 270 305 335 210 270 335 365 405 450 335 405 450 520 590 650 335 360 395 405 510 520 600 650 800 1000 mm 45 45 45 45 45 45 49 49 49 49 49 52 52 52 52 52 52 57 57 57 57 57 57 65 65 65 65 65 65 65 65 65 65 mm 41 41 41 41 41 45 45

27、45 45 45 45 48 48 48 48 48 48 52 52 52 52 52 52 60 60 60 60 60 60 60 60 60 60 mm 42 42 42 42 42 42 47 47 47 47 47 50 50 50 50 50 50 54 54 54 54 54 54 63 63 63 63 63 63 63 63 63 63 mm 96 118 140 158 165 178 119 135 151 169 185 105 132 161 177 195 209 136 164 185 207 234 257 100 107 118 122 154 157 18

28、1 195 240 300 mm 5.6 5.6 5.6 5.6 5.6 5.6 7.0 7.0 7.0 7.0 7.0 8.0 8.0 8.0 8.0 8.0 8.0 9.5 9.5 9.5 9.5 9.5 9.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 13.5 mm 101.6 123.6 145.6 163.6 170.6 183.6 126.0 142.0 158.0 176.0 192.0 113.0 140.0 169.0 185.0 203.0 217.0 145.0 173.5 194.5 216.5 243.5 266.5

29、113.5 120.5 131.5 135.5 167.5 170.5 194.5 208.5 253.5 313.5 mm 43.6 43.6 43.6 43.6 43.6 43.6 47.8 47.8 47.8 47.8 47.8 50.7 50.7 50.7 50.7 50.7 50.7 55.5 55.5 55.5 55.5 55.5 55.5 63.2 63.2 63.2 63.2 63.2 63.2 63.2 63.2 63.2 63.2 mm 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 2.9 3.2 3.2 3.2 3.2 3.2 3.2 3

30、.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 3.3 mm 5.3 5.3 5.3 5.3 5.3 5.3 5.5 5.5 5.5 5.5 5.5 5.6 5.6 5.6 5.6 5.6 5.6 6.0 6.0 6.0 6.0 6.0 6.0 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 mm 45.2 45.2 45.2 45.2 45.2 45.2 49.3 49.3 49.3 49.3 49.3 52.7 52.7 52.7 52.7 52.7 52.7 57.6 57.6 57.6

31、 57.6 57.6 57.6 65.9 65.9 65.9 65.9 65.9 65.9 65.9 65.9 65.9 65.9 a For product fill volumes reference should be made to BS3914. b Refers to internal diameter (see BS6966-3). c Tolerances are shown in Figure 2.BS7289:1990 BSI 11-1999 5 Figure 2 Dimensions of necked-in three-piece aerosol cans, with

32、tolerancesBS7289:1990 6 BSI 11-1999 Figure 3 Measurement of the contact heightBS7289:1990 BSI 11-1999 Publication(s) referred to BS3914, Specification for non-refillable metal aerosol dispensers of50mL to1400mL capacity and up to85mm diameter. BS6966, Light gauge metal containers. BS6966-3, Glossary

33、 of terms for aerosol cans and methods for determination of dimensions and capacities. BS7289:1990 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe a

34、nd at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products an

35、d services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an indi

36、vidual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to

37、orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Lib

38、rary and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards develo

39、pments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications

40、 of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission

41、from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.