BS 6413-2-1983 Lubricants industrial oils and related products (class L) - Classification for family F (spindle bearings bearings and associated clutches)《润滑剂、工业用油和相关产品(L级) 第2部分 F系.pdf

《BS 6413-2-1983 Lubricants industrial oils and related products (class L) - Classification for family F (spindle bearings bearings and associated clutches)《润滑剂、工业用油和相关产品(L级) 第2部分 F系.pdf》由会员分享，可在线阅读，更多相关《BS 6413-2-1983 Lubricants industrial oils and related products (class L) - Classification for family F (spindle bearings bearings and associated clutches)《润滑剂、工业用油和相关产品(L级) 第2部分 F系.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS 6413-2: 1983 ISO 6743-2: 1981 Lubricants, industrial oils and related products (class L) Part 2: Classification for family F (spindle bearings, bearings and associated clutches) ISO title: Lubricants, industrial oils and related products (classL) Classification Part 2: Family F (

2、Spindle bearings, bearings and associated clutches) UDC 665.765.001.33:621.892BS6413-2:1983 This British Standard, having been prepared under the directionof the Petroleum Standards Committee, was published under the authority ofthe Board of BSI and comes into effect on 31October1983 BSI 09-1999 The

3、 following BSI references relate to the work on this standard: Committee reference PTC/7 Draft for comment80/53917 DC ISBN 0 580 13442 3 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Petroleum Standards Committee (PTC/-) to Technical C

4、ommittee PTC/7 upon which the following bodies were represented: Association of Hydraulic Equipment Manufacturers British Electrical and Allied Manufacturers Association (BEAMA) British Gas Corporation British Gear Manufacturers Association British Lubricants Federation Limited British Railways Boar

5、d British Refrigeration and Air Conditioning Association Department of Industry (National Engineering Laboratory) Electricity Supply Industry in England and Wales Engineering Equipment and Materials Users Association Institute of Petroleum Institute of Refrigeration London Transport Executive Minist

6、ry of Defence Society of British Aerospace Companies Limited Coopted member Amendments issued since publication Amd. No. Date of issue CommentsBS6413-2:1983 BSI 09-1999 i Contents Page Committees responsible Inside front cover National foreword ii 1 Scope and field of application 1 2 Reference 1 3 E

7、xplanation of symbols 1 Publications referred to Inside back coverBS6413-2:1983 ii BSI 09-1999 National foreword This Part of this British Standard has been prepared under the direction of the Petroleum Standards Committee in order to provide a classification scheme for lubricants, industrial oils a

8、nd related products. It is identical with ISO6743-2:1981 “Lubricants, industrial oils and related products (class L) Classification Part 2: Family F (Spindle bearings, bearings and associated clutches)”, published by the International Organization for Standardization (ISO). ISO6743-2 was prepared as

9、 the result of discussions in Subcommittee4, Classifications and specifications, of Technical Committee28, Petroleum products and lubricants, in which the UK has participated. A general classification of petroleum products prepared in ISO/TC28 has allocated class L to lubricants. Part 0 of this stan

10、dard details the subdivision of class L into families of products, to each of which a code letter is allocated. This Part provides a detailed classification within family F of class L. Further Parts of the International Standard will provide a detailed classification within other families of class L

11、 and will be published as further Parts of this standard. A classification of machine tool lubricants has been separately published as BS5063 “Classification of rationalized range of lubricants for machine tool applications” and covers grades drawn from ISO3498:1979 “Lubricants for machine tools Cla

12、ssification”, but does not include all the grades in ISO3498. Terminology and conventions. The text of the International Standard has been approved as suitable for publication as a British Standard without deviation. Some terminology and certain conventions are not identical with those used in Briti

13、sh Standards; attention is drawn especially to the following. Wherever the words “part of ISO 6743” appear, referring to this standard, they should be read as “Part of BS 6413”. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are

14、responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-references International Standard Corresponding British Standard ISO 3448:1975 BS 4231:1982 Classification for viscosity grades of industrial liquid lubrican

15、ts (Identical) ISO 6743-0:1981 BS 6413 Lubricants, industrial oils and related products (class L) Part 0:1983 Classification (general) (Identical) Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2, an inside back cover and a back cover. This

16、standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS6413-2:1983 BSI 09-1999 1 1 Scope and field of application This part of ISO6743 establishes the detailed classification of family F (Spin

17、dle bearings, bearings and associated clutches) which belongs to the class L (Lubricants, industrial oils and related products). It should be read in conjunction with ISO6743-0. 2 Reference ISO 3448, Industrial liquid lubricants ISOviscosity classification. 3 Explanation of symbols used 3.1 This det

18、ailed classification of family F has been established by defining the categories of products required for the main applications of this family and at the final point for subdivision by referring to composition of corresponding products. 3.2 Each category is designated by a symbol consisting of a gro

19、up of letters, which together constitute a code. NOTEThe first letter of the code (F) identifies the family of the product considered but the second letter taken separately has no significance of its own. The designation of each category can be supplemented by the addition of viscosity grades accord

20、ing to ISO3448. 3.3 In this classification system, products are designated in a uniform manner. For example, a particular product may be designated in complete form, i.e.ISO-L-FD68, or in an abbreviated form, i.e.L-FD68, the number indicating the viscosity grade according to ISO3448.Classification o

21、f lubricants, industrial oils and related products (class L) Family F (Spindlebearings, bearings and associated clutches) Code letter General application Particular application More specific application Composition and special properties Symbol ISO-L Typical applications Remarks F Spindle bearings,

22、bearings and associated clutches Spindle bearings, bearings and associated clutches Refined mineral oils with improved properties, for example anti-corrosion and anti-oxidation, which may be obtained by additives FC Pressure, bath and oil mist (aerosol) lubrication of plain or rolling bearings and a

23、ssociated clutches Where clutches are involved anti-wear or EP additives should be avoided because of the risk of corrosion Spindle bearings, bearings Refined mineral oils with improved properties, for example anti-corrosion, anti-oxidation, anti-wear, which may be obtained by additives FD Pressure,

24、 bath and oil mist (aerosol) lubrication of plain or rolling bearings2 blankBS6413-2:1983 BSI 09-1999 Publications referred to See national foreword.BS 6413-2: 1983 ISO 6743-2: 1981 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsib

25、le for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments o

26、r editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on t

27、he inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should b

28、e addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide ran

29、ge of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fa

30、x:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in

31、 all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means

32、electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.