ASTM F3065 F3065M-2018 Standard Specification for Aircraft Propeller System Installation《飞机螺旋桨系统安装标准规范》.pdf

《ASTM F3065 F3065M-2018 Standard Specification for Aircraft Propeller System Installation《飞机螺旋桨系统安装标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM F3065 F3065M-2018 Standard Specification for Aircraft Propeller System Installation《飞机螺旋桨系统安装标准规范》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F3065/F3065M 18Standard Specification forAircraft Propeller System Installation1This standard is issued under the fixed designation F3065/F3065M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revisio

2、n. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification addresses the airworthiness require-ments for the installation and integration of propeller systems.1.2 This sp

3、ecification is applicable to aeroplanes as definedin F44 terminology standard.1.3 The applicant for a design approval must seek theindividual guidance to their respective CAA body concerningthe use of this standard as part of a certification plan. Forinformation on which CAA regulatory bodies have a

4、cceptedthis standard (in whole or in part) as a means of compliance totheir Small Aircraft Airworthiness regulations (Hereinafterreferred to as “the Rules”), refer to ASTM F44 webpage(www.ASTM.org/COMITTEE/F44.htm) which includes CAAwebsite links.1.4 UnitsThe values stated are SI units followed byIm

5、perial units in square brackets. The values stated in eachsystem may not be exact equivalents; therefore, each systemshall be used independently of the other. Combining valuesfrom the two systems may result in non-conformance with thestandard.1.5 This standard does not purport to address all of thes

6、afety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accor-d

7、ance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM S

8、tandards:2F3060 Terminology for Aircraft3. Terminology3.1 See Terminology F3060.4. Propeller Installation Aspects4.1 PropellerGeneral:4.1.1 Each propeller must:4.1.1.1 Have a type certificate, or4.1.1.2 Meet the requirements acceptable to the certifyingaviation authority for inclusion in the approve

9、d aeroplane.4.1.2 Engine power and propeller shaft rotational speed maynot exceed the limits for which the propeller is certificated orapproved.4.2 Feathering PropellersEach featherable propeller musthave a means to un-feather in flight.4.3 Variable-Pitch PropellersThe propeller blade pitchcontrol s

10、ystem must meet the following requirements:4.3.1 No single failure or malfunction in the propellersystem will result in unintended travel of the propeller bladesto a position below the in-flight low-pitch position. Failure ofstructural elements need not be considered if the occurrence ofsuch a failu

11、re is shown to be extremely remote.4.3.2 For propellers incorporating a method to select bladepitch below the in-flight low pitch position, provisions must bemade to sense and indicate to the flight crew that the propellerblades are below that position by a defined amount. Themethod for sensing and

12、indicating the propeller blade pitchposition must be such that its failure does not affect the controlof the propeller.4.3.3 The propeller control system, operating in normal andalternative operating modes and in transition between operat-ing modes, performs the defined functions throughout thedecla

13、red operating conditions and flight envelope.1This specification is under the jurisdiction ofASTM Committee F44 on GeneralAviation Aircraft and is the direct responsibility of Subcommittee F44.40 onPowerplant.Current edition approved Jan. 1, 2018. Published January 2018. Originallyapproved in 2015.

14、Last previous edition approved in 2015 as F3065/F3065M 15.DOI: 10.1520/F3065_F3065M-18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summar

15、y page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles f

16、or theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.14.3.4 The propeller control system functionality is notadversely affected by the declared environmental conditions,including temperature, elect

17、romagnetic interference (EMI),high intensity radiated fields (HIRF) and lightning.4.3.5 A method is provided to indicate that an operatingmode change has occurred if flight crew action is required.4.3.6 No single failure or malfunction of electrical orelectronic components in the control system resu

18、lts in ahazardous propeller effect.4.3.7 Failures or malfunctions directly affecting the propel-ler control system in a typical airplane, such as structuralfailures of attachments to the control, fire, or overheat, do notlead to a hazardous propeller effect.4.3.8 The loss of normal propeller pitch c

19、ontrol does notcause a hazardous propeller effect under the intended operatingconditions.4.3.9 The failure or corruption of data or signals sharedacross propellers does not cause a hazardous propeller effect.4.3.10 Electronic propeller control system imbedded soft-ware must be designed and implement

20、ed by a method approvedby the Civil Aviation Authority that is consistent with thecriticality of the performed functions and that minimizes theexistence of software errors.4.3.11 The propeller control system must be designed andconstructed so that the failure or corruption of airplane-supplied data

21、does not result in hazardous propeller effects.4.3.12 The propeller control system must be designed andconstructed so that the loss, interruption or abnormal charac-teristic of airplane-supplied electrical power does not result inhazardous propeller effects.4.3.13 Each propeller blade pitch control

22、systemcomponent, including governors, pitch change assemblies, andfeathering system components, can withstand cyclic operationthat simulates the normal load and pitch change travel to whichthe component would be subjected during a minimum of 1000h of typical operation in service.4.3.14 Propeller com

23、ponents that contain hydraulic pressureand whose structural failure or leakage from a structural failurecould cause a hazardous propeller effect demonstrate structuralintegrity by:4.3.14.1 A proof pressure test to 1.5 the maximum oper-ating pressure for one minute without permanent deformationor lea

24、kage that would prevent performance of the intendedfunction, and4.3.14.2 A burst pressure test to 2.0 the maximum operat-ing pressure for one minute without failure. Leakage ispermitted and seals may be excluded from the test.4.4 Pusher Propeller Installation:4.4.1 All engine cowling, access doors,

25、and other removableitems must be designed to have a remote probability ofseparation that could cause contact with the pusher propeller.4.4.2 Each pusher propeller must be marked so that the discis conspicuous under normal daylight ground conditions.4.4.3 If the engine exhaust gases are discharged in

26、to thepusher propeller disc, it must be shown by tests, or analysissupported by tests, that the propeller is capable of continuoussafe operation.4.5 Propeller Clearance:4.5.1 Propeller clearances in section 4.5 are the minimumallowable, unless otherwise substantiated, under the followingconditions:4

27、.5.1.1 With the most adverse combination of aeroplaneweight and center of gravity, and4.5.1.2 With the propeller in the most adverse pitch posi-tion.4.5.2 Ground Clearance with Forward Mounted Propellers:4.5.2.1 Normal OperationWith landing gear staticallydeflected and the aeroplane in the level, no

28、rmal takeoff, ortaxiing attitude, whichever is most critical; there must be aclearance between each propeller and the ground of at least:(1) 18 cm 7 in. for each aeroplane with nose wheellanding gear, or(2) 23 cm 9 in. for each aeroplane with tail wheel landinggear.4.5.2.2 Deflated and Bottomed Stru

29、tsFor each aeroplanewith conventional landing gear struts using fluid or mechanicalmeans for absorbing landing shocks, there must be positiveclearance between the propeller and the ground in the leveltakeoff attitude with the critical tire completely deflated and thecorresponding landing gear strut

30、bottomed.4.5.2.3 Leaf Spring StrutsPositive clearance for aero-planes using leaf spring struts is shown with a deflectioncorresponding to 1.5 g.4.5.3 Ground Clearance with Aft-Mounted PropellersInaddition to the clearances specified in 4.5.2, an aeroplane withan aft mounted propeller must be designe

31、d such that thepropeller will not contact the runway surface when the aero-plane is in the maximum pitch attitude attainable during normaltakeoffs and landings.4.5.4 Water Clearance:4.5.4.1 There must be a clearance of at least 46 cm 18 in.between each propeller and the water.4.5.4.2 The clearance m

32、ay be reduced if the spray does notdangerously obscure the vision of the pilots or damage thepropellers or other parts of the seaplane or amphibian at anytime during taxiing, takeoff, or landing.4.5.5 Structural ClearanceThere must be:4.5.5.1 At least 25 mm 1 in. radial clearance between theblade ti

33、ps and the aeroplane structure, plus any additionalradial clearance necessary to prevent harmful vibration;4.5.5.2 At least 12.7 mm 12 in. longitudinal clearancebetween the propeller blades or cuffs and stationary parts of theaeroplane; and4.5.5.3 Positive clearance between other rotating parts ofth

34、e propeller or spinner and stationary parts of the aeroplane.4.5.6 Clearance from Occupant(s)There must be adequateclearance or shielding between the occupant(s) and thepropeller, such that it is not possible for the occupant(s), whenseated and strapped in, to contact the propeller.5. Structural Asp

35、ects5.1 Propeller Vibration and Fatigue:5.1.1 Section 5.1 does not apply to fixed-pitch wood pro-pellers of conventional design.5.1.2 The magnitude of the propeller vibration stresses orloads, including any stress peaks and resonant conditions,F3065/F3065M 182throughout the normal operational envelo

36、pe of the aeroplanemust be determined by either:5.1.2.1 Measurement of stresses or loads through directtesting or analysis based on direct testing of the propeller onthe aeroplane and engine installation for which approval issought; or5.1.2.2 Comparison of the propeller to similar propellersinstalle

37、d on similar aeroplane installations for which thesemeasurements have been made.5.1.3 A fatigue evaluation of the propeller hub, blades, andblade retention must be made to show that failure due to fatiguewill be avoided throughout the operational life of the propeller.5.1.3.1 The fatigue evaluation

38、must use the structural dataobtained in accordance with the propeller regulatory require-ments or specifications and the vibration data obtained from5.1.2.5.1.3.2 The fatigue evaluation must include:(1) The intended loading spectra including reasonablyforeseeable propeller vibration and cyclic load

39、patterns,(2) Identified emergency conditions,(3) Allowable over speeds and over torques,(4) The effects of temperatures and humidity expected inservice,(5) The effects of aeroplane operating airworthinesslimitations, and(6) The effects of propeller operating airworthiness limita-tions.5.1.3.3 The fa

40、tigue evaluation must consider any otherpropeller component whose failure due to fatigue could becatastrophic to the aeroplane.5.1.4 The applicant must demonstrate by tests, analysisbased on tests, or previous experience on similar designs thatthe propeller does not experience harmful effects of flu

41、tterthroughout the normal operational envelope of the aeroplane.5.1.5 Any other test method or service experience thatproves the safety of the installation acceptable to the certifyingaviation authority may be used in place of subsections 5.1.2,5.1.3, and 5.1.4.6. Propeller Control Limitations6.1 Pr

42、opeller Speed and Pitch Limits:6.1.1 The propeller speed and pitch must be limited tovalues that will assure safe operation under normal operatingconditions.6.1.2 For each propeller whose pitch cannot be controlled inflight.6.1.2.1 During takeoff and initial climb at the all engine(s)operating climb

43、 speed, the propeller must limit the enginer.p.m., at full throttle or at maximum allowable takeoff mani-fold pressure, to a speed not greater than the maximumallowable takeoff r.p.m.; and6.1.2.2 During a closed throttle glide, at VNE, the propellermay not cause an engine speed above 110 % of maximu

44、mcontinuous speed.6.1.3 Each propeller that can be controlled in flight, but thatdoes not have constant speed controls, must have a means tolimit the pitch range so that:6.1.3.1 The lowest possible pitch allows compliance withsection 6.1.2.1; and6.1.3.2 The highest possible pitch allows compliance w

45、ithsection 6.1.2.2.6.1.4 Each controllable pitch propeller with constant speedcontrols must have:6.1.4.1 With the governor in operation, a means at thegovernor to limit the maximum engine speed to the maximumallowable takeoff r.p.m.; and6.1.4.2 With the governor inoperative, there must be ameans to

46、limit the maximum engine speed to 103 % of themaximum allowable takeoff r.p.m. or maximum approvedoverspeed, with:(1) The propeller blades at the lowest possible pitch,(2) Takeoff power,(3) The aeroplane stationary, and(4) No wind.6.2 Propeller Reversing Systems:6.2.1 Each system must be designed so

47、 that no singlefailure, likely combination of failures or malfunction of thesystem will result in unwanted reverse thrust under anyoperating condition.6.2.1.1 Failure of structural elements need not be consideredif the probability of this type of failure is extremely remote.6.2.1.2 Compliance must b

48、e shown by failure analysis, ortesting, or both, for propeller systems that allow the propellerblades to move from the flight low-pitch position to a positionthat is substantially less than the normal flight, low-pitchposition.6.2.1.3 The analysis may include or be supported by theanalysis from the

49、propeller type certification. Credit will begiven for pertinent analysis and testing completed by theengine and propeller manufacturers.6.2.2 For Turbopropeller-Powered, Level 4 Aircraft:6.2.2.1 Each system intended for in-flight use must bedesigned so that no unsafe condition will result during normaloperation of the system, or from any failure, or likely combi-nation of failures, of the reversing system, under any operatingcondition, including ground operation.6.2.2.2 Failure of structural elements need not be consideredif the probability of this type of fai