ASTM D6788-2002(2007) Standard Specification for Repositionable Pressure-Sensitive Flags《可贮藏的压敏旗状书签的标准规范》.pdf
《ASTM D6788-2002(2007) Standard Specification for Repositionable Pressure-Sensitive Flags《可贮藏的压敏旗状书签的标准规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM D6788-2002(2007) Standard Specification for Repositionable Pressure-Sensitive Flags《可贮藏的压敏旗状书签的标准规范》.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D 6788 02 (Reapproved 2007)Standard Specification forRepositionable Pressure-Sensitive Flags1This standard is issued under the fixed designation D 6788; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last
2、revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books,periodica
3、ls, and so forth.1.2 The values stated in either inch-pound or SI units are tobe regarded separately as standard. The values stated in eachsystem are not exact equivalents; therefore, each system mustbe used independently, without combining values in any way.1.3 The following safety hazards caveat p
4、ertains only to thetest methods portion, Section 14, of this specification. Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the
5、applicability of regulatory require-ments prior to use.2. Referenced Documents2.1 ASTM Standards:2D 996 Terminology of Packaging and Distribution Environ-mentsD 3330/D 3330M Test Method for Peel Adhesion ofPressure-Sensitive TapeD 3652/D 3652M Test Method for Thickness of Pressure-Sensitive TapesD 3
6、715/D 3715M Practice for Quality Assurance ofPressure-Sensitive TapesD 3811/D 3811M Test Method for Unwind Force ofPressure-Sensitive TapesD 3951 Practice for Commercial PackagingD 4332 Practice for Conditioning Containers, Packages, orPackaging Components for Testing2.2 Federal Specifications:CID A
7、-A-2826 Tabs, Signal (Repositionable), cancelledNovember, 19, 19993PPP-T-680 Federal Packaging Standard42.3 ISO Standard:ISO 9002 Quality Systems Model for Quality Assurance inProduction and Installation52.4 ANSI/ASQC Standard:ANSI/ASQC Z 1.9 Sampling and Tables for Inspection byVariables for Percen
8、t Defective53. Terminology3.1 DefinitionsGeneral terms in this specification aredefined in Terminology D 996.3.2 pad of flagsa vertical stack of individual flags withone flag positioned on top of the other.4. Significance and Use4.1 The repositionable, pressure-sensitive flags covered bythis specifi
9、cation are intended for marking, flagging, andindexing of documents, books, periodicals, and so forth. Flagsconsist of a single sheet of matte film partially covered byadhesive. There is a non-adhesive tab or section at one end ofthe flag for easy removal from surfaces. The flag is removablefrom mos
10、t surfaces including paper. Flags may have a printedmessage on the top side of the flag.4.2 This specification replaces U.S. Government CID A-A-2826.5. Classification5.1 Type 1 flags are 1 in. wide (25 mm) and have a coloredtab at one end.5.2 Type 2 flags are 1 in. wide (25 mm) and have a printedmes
11、sage on the top side of the flag.1This specification is under the jurisdiction of ASTM Committee D10 onPackaging and is the direct responsibility of Subcommittee D10.14 on Tape andLabels.Current edition approved Oct. 1, 2007. Published November 2007. Originallyapproved in 2002. Last previous edition
12、 approved in 2002 as D 6788 02.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Governmen
13、t Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.4Available from www.dia.mil. For additional information or comments write toGeneral Services Administration, Federal Supply Service, FSS Aquisition Manage-ment Center,
14、 Environmental Programs and Engineering Policy Division (FCOE),Washington, DC 20406.5Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA
15、19428-2959, United States.5.3 Type 3 flags are 2 in. wide (50 mm) and have a white tabat one end to highlight writing.5.4 Type 4 flags are12 in. wide (12 mm) and have a coloredtab at one end.5.5 Type 5 flags are12 in. wide (12 mm) and have an arrowor a message printed on the top side of the flag.6.
16、Ordering Information6.1 The inquiry or order shall include the following:6.1.1 ASTM designation and date of issue,6.1.2 Type required (see Section 5),6.1.3 Number of flags in each dispenser,6.1.4 Color of tab on flag for unprinted flags,6.1.5 Printed message, if any,6.1.6 When testing and inspection
17、 certification is required(see Section 17), and6.1.7 For government orders, conformance to federal pack-aging standards.7. Materials and Manufacture7.1 The materials used in construction of the flags shallconform to the requirements of this specification.7.2 BackingThe film backing shall consist of
18、polyester,polypropylene, or polyethylene film. The backing shall havesufficient strength to resist tearing by hand. The backing shallhave a transparent matte surface on one side that is writable bypens and pencils.7.2.1 Writing on the flags shall not exhibit feathering,spreading, skipping, beading,
19、visible discontinuities or fadingof ink when writing with any writing instrument including ametal roller pen, felt tip pen, permanent marker, ball point pen,or fountain pen.7.2.2 Individual flags shall release easily from the padwithout leaving any trace of adhesive on the underlying sheet.7.3 Adhes
20、iveThe adhesive shall be pressure-sensitive,repositionable, and water-insoluble. Each flag in the pad shallhave a coating of the adhesive on the back side of the flag.7.3.1 The adhesive coating shall be applied flush to onehorizontal edge of the flag and shall extend the entire width ofthe flag. The
21、 adhesive shall cover at least 60 % of the surfacearea of the flag to ensure secure holding of the flag to a surface.7.3.2 The adhesive shall leave no visible residue on thesurface to which it is applied and removed. Removal of the flagfrom paper shall not rip or damage the paper.7.4 Pad and Dispens
22、erSingle flags shall be stacked in apad. The pad of flags shall be contained in a dispenser packagethat allows single flag dispensing through a slot in thedispenser. The dispenser shall be designed so that when a flagis removed for use, the next flag in the pad shall protrude fromthe slot for the ne
23、xt application. This shall continue until thepad is consumed. The dispenser shall be of sufficient strengthto last the life of the pad. One flag dispenser may contain asingle pad or several pads of flags.8. Conditioning8.1 Condition all samples in the standard conditioningatmosphere as described in
24、Practice D 4332 for a period of notless than 24 h before testing.8.2 Conduct tests in an atmosphere of 50 6 2 % relativehumidity and 23.0 6 2.0C as described in Practice D 4332.9. Physical Properties9.1 The flags shall comply with the physical test require-ments listed in Table 1.10. Dimensions, Mas
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD678820022007STANDARDSPECIFICATIONFORREPOSITIONABLEPRESSURESENSITIVEFLAGS 贮藏 压敏旗状 书签 标准规范 PDF

链接地址:http://www.mydoc123.com/p-523578.html