ASTM D1370-2000(2007) Standard Test Method for Contact Compatibility Between Asphaltic Materials (Oliensis Test)《沥青材料间接触相容性的标准试验方法(奥林萨斯试验)》.pdf

《ASTM D1370-2000(2007) Standard Test Method for Contact Compatibility Between Asphaltic Materials (Oliensis Test)《沥青材料间接触相容性的标准试验方法(奥林萨斯试验)》.pdf》由会员分享，可在线阅读，更多相关《ASTM D1370-2000(2007) Standard Test Method for Contact Compatibility Between Asphaltic Materials (Oliensis Test)《沥青材料间接触相容性的标准试验方法(奥林萨斯试验)》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: D 1370 00 (Reapproved 2007)Standard Test Method forContact Compatibility Between Asphaltic Materials (OliensisTest)1This standard is issued under the fixed designation D 1370; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revi

2、sion, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method provides a means for evaluatingcontact compatibility between asphaltic materials.

3、It is gener-ally used to determine compatibility between the saturant andcoating used in the manufacture of prepared roofings.2Coatingand saturant will be referred to, but comparable asphalticmaterials may be tested where this test procedure seemsapplicable.1.2 The values stated in SI units are to b

4、e regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and

5、determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3E11 Specification for Wire Cloth and Sieves for TestingPurposes3. Summary of Test Method3.1 A small drop of molten saturant is placed on the freshlytalced surface of the coating, and compat

6、ibility is judged by thedegree to which an oily ring develops in the talc surroundingthe drop.24. Significance and Use4.1 This test method assesses the degree to which asphaltsinteract with one another. It can indicate possible futureproblems, especially blistering, in a roofing product if incom-pat

7、ible asphalts are in contact in the product.5. Apparatus5.1 Container, lid of 85-g (3-oz) ointment box, or equiva-lent container.5.2 Analytical Balance, having an accuracy of 61.0 mg.5.3 Sieve 45-m (No. 325). Detailed requirements for thesesieves are given in Specification E11.5.4 Dropping Device, a

8、 fine wire 1.0 mm (0.04 in.) indiameter.5.5 Oven, constant-temperature, capable of maintaining thetest temperature within 61.0C (61.8F).5.6 Small Scale, graduated in 0.1 mm divisions.5.7 Magnifying Glass or Stereo Microscope, approximateminimum of 43.5.8 Talc, pure, of the soapstone variety, ground

9、so that atleast 70 % passes the 45-m (No. 325) sieve, and oven-dried at110C (230F).NOTE 1When this test method is being used in purchase specifica-tions, both the purchaser and the seller shall use the same talc. Talc fromLuzenac America, Inc.4has been found to be suitable for this test.6. Procedure

10、6.1 Melt a portion of the coating at the minimum tempera-ture required to render it fluid, stirring with the fine wire toeliminate bubbles, and pour it into the clean 85-g (3 oz) tin lidto a thickness of 3.0 to 6.0 mm(18 to14 in.). Pour carefully, soas to provide a substantially smooth surface free

11、of bubbles andother surface blemishes. After the coating material has cooled,determine the weight and surface area of the filled container.6.2 Make a preliminary dusting of talc by covering thecoating surface with talc and removing the excess, nonadherentdust by inverting the container and dropping

12、it approximately25 mm (1 in.) onto the table top.6.3 Make a final application of talc through the 45-m (No.325) sieve, held 20 to 25 mm (34 to 1 in.) above the surface of1This test method is under the jurisdiction ofASTM Committee D08 on Roofingand Waterproofing and is the direct responsibility of S

13、ubcommittee D08.02 onPrepared Roofings, Shingles and Siding Materials.Current edition approved June 1, 2007. Published June 2007. Originallyapproved in 1984. Last previous edition approved in 2000 as D 1370 00.2This test determines only exudative incompatibility. For application of thisprocedure to

14、determination of insudative incompatibility, see “Compatibility Be-tween BitumensExudation versus Insudation,” by Oliensis, G. L., MaterialsResearch and Standards, Vol 1, No. 9, September 1961, p. 723.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Servi

15、ce at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4The sole source of supply known to the committee at this time is the LuzenacAmerica, Inc., 9000 East Nichols Avenue, Englewood, CO, 80112. If you are awareof a

16、lternative suppliers, please provide this information to ASTM Headquarters.Your comments will receive careful consideration at a meeting of the responsibletechnical committee,1which you may attend.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, Un

17、ited States.the coating, by gently shaking or tapping the sieve until asmooth, uniform film of talc, weighing 0.004 g 6 10 % persquare centimetre, has been applied.6.4 Place 3 drops of molten saturant, each about 3.0 6 0.5mm (18 6164 in.) in diameter, on the talced surface of thecoating. Form the dr

18、ops by plunging the wire into the moltensaturant and, after the excess has drained off, allowing suitablysized drops to fall on the talc from a sufficient height to formsubstantially spherical drops.6.5 Place the prepared specimen in the test oven, so regu-lated as to maintain the specimen at the re

19、commended testtemperature, within 61.0C (61.8F), for 72 h (Note 2). Aftercooling, examine the specimen and measure any oily ringformed around the periphery of the drop, recording its width tothe nearest 0.1 mm. Measure the width from the line of contactof talc and drop to the outer limit of the oil

20、ring.NOTE 2The recommended test temperature for roofing materials is50C (122F), but this may be altered to accommodate variations in thebitumens being tested.7. Report7.1 Report the results of the compatibility test as the widthin millimetres of the ring developed in the specified testtemperature.8.

21、 Precision and Bias8.1 RepeatabilityDuplicate results by the same operatorshould not differ by more than 0.1 mm.8.2 ReproducibilityResults between laboratories shouldbe reproducible within 0.2 mm.9. Keywords9.1 asphaltic materials; coating asphalt; compatibility; con-tact; oliensis test; saturant as

22、phaltASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights

23、, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional st

24、andardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Co

25、mmittee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 1370 00 (2007)2