ASTM C615-2003 Standard Specification for Granite Dimension Stone《花岗岩规格石料标准规范》.pdf

《ASTM C615-2003 Standard Specification for Granite Dimension Stone《花岗岩规格石料标准规范》.pdf》由会员分享，可在线阅读，更多相关《ASTM C615-2003 Standard Specification for Granite Dimension Stone《花岗岩规格石料标准规范》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: C 615 03Standard Specification forGranite Dimension Stone1This standard is issued under the fixed designation C 615; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses in

2、dicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers the material characteristics,physical requirements,

3、 and sampling appropriate to the selec-tion of granite for general building and structural purposes.1.2 Granite dimension stone shall include stone that issawed, cut, split, or otherwise finished or shaped, and shallspecifically exclude molded, cast, or otherwise artificiallyaggregated units compose

4、d of fragments, crushed and brokenstone.2. Referenced Documents2.1 ASTM Standards:2C 97 Test Methods for Absorption and Bulk Specific Grav-ity of Dimension StoneC 99 Test Method for Modulus of Rupture of DimensionStoneC 119 Terminology Relating to Dimension StoneC 170 Test Method for Compressive Str

5、ength of DimensionStoneC 241 Test Method for Abrasion Resistance of Stone Sub-jected to Foot TrafficC 880 Test Method for Flexural Strength of DimensionStoneC 1353 Test Method Using the Taber Abraser for AbrasionResistance of Dimension Stone Subjected to Foot Traffic3. Terminology3.1 DefinitionsAll

6、definitions are in accordance with Ter-minology C 119.4. Classification4.1 Granite dimension stone under this specification shall begranite used for:4.1.1 Exterior and interior cladding of buildings and struc-tures;4.1.2 Curbstone, paving, and landscape features;4.1.3 Structural components having es

7、tablished dimensions;4.1.4 Grade separations and retaining walls; and4.1.5 Monuments.5. Physical Properties5.1 Granite supplied under this specification shall conformto the physical requirements prescribed in Table 1. See 5.1.2for possible variations from this table.5.1.1 The minimum compressive str

8、ength, flexural strength,and modulus of rupture shall be based upon the minimumaverage strength of specimens tested in four conditions: wet ordry and parallel or perpendicular to rift.5.1.2 The physical properties given in Table 1 representproperties of granite that have a history of successful use

9、forgeneral building and structural purposes. Granite with strengthor abrasion resistance less than the minimum values prescribedin Table 1 may be used provided that competent engineeringauthority has evaluated relevant characteristics of the granite.This evaluation shall consider both structural eff

10、ects andmaterial characteristics such as durability, permanent volumechange, modulus of elasticity. thermal expansion, and the like.5.2 Granite shall be sound, durable, and free of spalls,cracks, open seams, pits, or other defects that are likely toimpair its structural integrity in its intended use

11、.5.3 Granite shall be free of minerals that may cause objec-tionable staining under normal environments of use.5.4 The desired color and texture, with their permissiblenatural variations in material characteristics for all material tobe produced for the project, shall be established by controlsample

12、s. Select representative samples by viewing a sufficientnumber of physical samples prior to production that show thecomplete range of variations in color and texture of the granitespecified.6. Sampling6.1 Samples, if required, for testing to determine the char-acteristics and physical properties sha

13、ll be representative of thegranite to be used.1This specification is under the jurisdiction of ASTM Committee C18 onDimension Stone and is the direct responsibility of Subcommittee C18.03 onMaterial Specifications.Current edition approved Dec. 1, 2003. Published January 2004. Originallyapproved in 1

14、968. Last previous edition approved in 1999 as C 615 99.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copy

15、right ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised

16、 that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either rea

17、pproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If yo

18、u feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual

19、 reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Physical RequirementsNOTEThe material property values in Table

20、1 were established using samples prepared according to the individual test methods. Finishes, other thanthose specified in the individual test methods, may result in a deviation from established values.Physical Property Test Requirements Test Method(s)Absorption by weight, max, % 0.40 C 97Density, m

21、in, lb/ft3(kg/m3) 160 (2560) C 97Compressive strength, min, psi (MPa) 19 000 (131) C 170Modulus of rupture, min, psi (MPa) 1500 (10.34) C 99Abrasion resistance, min, HaA,B,C25 C 241/C 1353Flexural strength, min, psi (MPa) 1200 (8.27) C 880APertains only to stone subject to foot traffic.BThe supplier

22、 of the No. 60 Alundum abrasive, Norton, has indicated that the formula for Norton treatment 138S has beeen changed. The new abrasive is currently moreaggressive, resulting in lower abrasive hardness values (Ha) than when the standard was initially established. As such, care should be taken when int

23、erpreting Havaluesfrom tests using the new abrasive, particulary with regard to current ASTM stone standard specification requirements for abrasion resistance, which were developed whenthe original abrasive was still in use. Committee C-18 is actively studying alternatives to address this issue.CAbrasion Resistance Test Method C 1353 will eventually replace Test Method C 241 and it is not necessary to perform both tests. Availability of the proper equipmentand materials by the testing laboratory may determine which test is performed.C615032