ANSI ISEA 101-2014 American National Standard for Limited-Use and Disposable Coveralls-Size and Labeling Requirements.pdf

《ANSI ISEA 101-2014 American National Standard for Limited-Use and Disposable Coveralls-Size and Labeling Requirements.pdf》由会员分享，可在线阅读，更多相关《ANSI ISEA 101-2014 American National Standard for Limited-Use and Disposable Coveralls-Size and Labeling Requirements.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI/ISEA 101-2014 Revision of ANSI/ISEA 101-1996 American National Standard for Limited-Use and Disposable Coveralls Size and Labeling Requirements Secretariat International Safety Equipment Association Approved July 8, 2014 American National Standards Institute, Inc. American National Standard An

2、 American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect p

3、reclude anyone, whether they have approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National Standards are subject to periodic review and users are cautioned to obtain the latest editions. The

4、 American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no persons shall have the right or authority to issue an interpretation of an American National Standard in the name of the American Nati

5、onal Standards Institute. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the date of publica

6、tion. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute. Published by International Safety Equipment Association 1901 North Moore Street, Suite 808, Arlington, Virginia 22209 Copyright 2014 by In

7、ternational Safety Equipment Association All rights reserved. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. Printed in the United States of America Foreword This Foreword is not part o

8、f American National Standard ANSI/ISEA 101-2014) This standard provides minimum size, packaging and labeling requirements for limited-use and disposable coveralls. Garments covered under this standard are used in a variety of workplaces including grain and milling operations, automotive repair, pain

9、ting and dry chemical applications, abrasive blasting, food processing and construction work. The standard also provides guidance on the proper size selection of such garments. This ANSI/ISEA 101-2014 standard updates the 1996 edition by expanding the sizing chart to accommodate a majority of the wo

10、rking population who utilize such garments. In addition, the Appendix details a set of tests designed to validate the sizing of a garment selected for a worker based on height and weight. ANSI/ISEA 101-2014 was processed and approved using consensus procedures prescribed by the American National Sta

11、ndards Institute (ANSI). The following organizations were contacted prior to the approval of this standard. Inclusion in this list does not necessarily imply that a listed organization concurred with the submittal of the proposed standard to ANSI. American Coatings Association Argus Hazco Atlas Indu

12、strial Contractors Honeywell Safety Products International Safety Equipment Association National Institute for Occupational Safety and Health National Waste (2) Size designation; (3) Number of this specific standard (ANSI/ISEA 101-2014); and. (4) Fabric identification. 6. Minimum Package Labeling Re

13、quirements 6.1 Label Type Each package shall be marked legibly. 6.2 Label Content For each package, the following information shall be provided, in at least English: (1) Name of manufacturer or other means of identification of the manufacturer; (2) Size designation; (3) Number of this specific stand

14、ard, (ANSI/ISEA 101-2014); (4) Fabric identification; and (5) Number of garments in the package. ANSI/ISEA 101-2014 7 TABLE 1: Finished Minimum Dimensions of Limited-Use and Disposal Protective Coveralls Size Designation Dimension for Measurement Location, in inches (centimeters) (1) Chest (2) Insea

15、m (3) Sleeve Outseam (4) Body Length (5) Sleeve Opening (6) Leg Opening (7) Front Opening X-Small 20.5 (52.1) 26.5 (67.3) 29.0 (73.7) 31.0 (78.7) 5.5 (14.0) 9.5 (24.1) 21.5 (54.6) Small 22.0 (55.9) 27.5 (69.9) 31.0 (78.7) 33.0 (83.8) 5.5 (14.0) 9.5 (24.1) 21.5 (54.6) Medium 23.5 (59.7) 28.0 (71.1) 3

16、2.5 (82.6) 35.0 (88.9) 6.0 (15.2) 10.0 (25.4) 25.5 (64.8) Large 25.0 (63.5) 29.0 (73.7) 33.5 (85.1) 37.0 (94.0) 6.0 (15.2) 10.0 (25.4) 25.5 (64.8) X-Large 26.5 (67.3) 29.5 (74.9) 35.0 (88.9) 38.5 (97.8) 6.0 (15.2) 10.0 (25.4) 25.5 (64.8) 2XL 28.0 (71.1) 30.5 (77.5) 36.5 (92.7) 40.5 (102.9) 6.0 (15.2

17、) 10.0 (25.4) 27.5 (69.9) 3XL 29.5 (74.9) 31.5 (80.0) 37.0 (94.0) 42.5 (108.0) 6.0 (15.2) 10.5 (26.7) 27.5 (69.9) 4XL 30.5 (77.5) 32.0 (81.3) 37.5 (95.3) 44.5 (113.0) 6.0 (15.2) 10.5 (26.7) 27.5 (69.9) 5XL 31.0 (78.7) 33.5 (85.1) 38.0 (96.5) 46.0 (116.8) 6.0 (15.2) 10.5 (26.7) 28.0 (71.1) 6XL 33.0 (

18、83.8) 34.5 (87.6) 38.5 (97.8) 47.5 (120.7) 6.5 (16.5) 10.5 (26.7) 28.0 (71.1) ANSI/ISEA 101-2014 8 (1) Chest (2) Inseam (3) Sleeve outseam (4) Body length (5) Sleeve opening (6) Leg opening (7) Front opening Figure 1: Measurement Locations for Coveralls ANSI/ISEA 101-2014 9 Appendix A. Sizing Test P

19、rotocol for Garment Selection A.1 Sizing Chart (See Figure A-1) Knowing an individuals height and weight will enable the user to have a starting point in proper size selection. Recommendations for sizing, based on height and weight, are included as Figure A-1. A.2 Test Protocol A.2.1 Validating Size

20、 Use the test movements in Section A.2.3 to validate the size selection for the garment. Prior to conducting the test protocol, the test subject shall select one of the options in Section A.2.2 to secure the arm and leg ends. A.2.2 Options for Securing the Garment A.2.2.1 Option A. Test protocol is

21、conducted with coveralls that do not have arm and leg ends fixed to the wearer. If the garment has boots and/or hood, these shall be used in correct position during the test program. A.2.2.2 Option B. Test protocol is conducted with arm and leg ends taped to the wearer. Tape shall be attached in suc

22、h a manner that the ends of the coverall arm and leg do not change position on the wearer. To tape the wrist, position the coverall sleeve end on the wrist bone of the wearer. Tape the coverall in. (12.7 mm) above the sleeve and wrist bone. To tape the leg, position the coverall leg end on the ankle

23、 bone of the wearer. Tape the coverall in. (12.7 mm) above the leg end and ankle bone. If the coverall has a hood it shall be worn properly during the test protocol. A.2.3 Test Movements (1) Kneel on both knees, lean forward and place both hands on the floor 18 in. (45.7 cm) in front of the knees. C

24、rawl forward 10 feet (3.05 m) on hands and knees. (2) Climb ladder at least four steps. (3) Position hands at chest level with palms out. Reach directly overhead, interlock thumbs, extend arms upward. (4) At right thigh area, lift pant leg slightly and kneel on right knee. Place sole of left foot on

25、 floor with left knee bent 90 degrees. Touch thumb of right hand to toe of left shoe. Repeat exercise using the alternate side of the body. (5) Extend arms fully in front of body, lock thumbs together, twist upper body 90 degrees left and right. (6) Stand with feet shoulder width apart, arms at side

26、s. Raise arms until they are parallel to floor in front of body. Squat down as far as possible. (7) Kneel as in Movement (4), left arm hanging loosely at side. Fully extend right arm overhead. Repeat the exercises using the alternate side of the body. A.3 Evaluation Upon completion of the test program using Option A or B, inspect the garment for tears or rips in both the fabric and the seams. If rips or tears are present, consider using one size larger garment. ANSI/ISEA 101-2014 10 Figure A-1.Recommended SizingChart for Limited-Use and Disposable Coveralls