ANSI IEEE 802.20B-2010 Local and metropolitan area networks Virtual Bridged Local Area Networks Amendment 15 Bridging of IEEE 802.20 (IEEE Computer Society).pdf

《ANSI IEEE 802.20B-2010 Local and metropolitan area networks Virtual Bridged Local Area Networks Amendment 15 Bridging of IEEE 802.20 (IEEE Computer Society).pdf》由会员分享，可在线阅读，更多相关《ANSI IEEE 802.20B-2010 Local and metropolitan area networks Virtual Bridged Local Area Networks Amendment 15 Bridging of IEEE 802.20 (IEEE Computer Society).pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 Virtual Bridged Local Area NetworksSponsored by the LAN/MAN Standards Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA 19 November 2010IEEE Computer Society IEEE Std 802.20b-2010(Amendment to IEEE Std 802.1Q-2005) Amendment 15: Bridging of IEEE 802.20 IEEE Standard for Local and metropolita

2、n area networks IEEE Std 802.20b-2010 (Amendment to IEEE Std 802.1Q-2005) IEEE Standard for Local and metropolitan area networks Virtual Bridged Local Area Networks Amendment 15: Bridging of IEEE 802.20 Sponsor LAN/MAN Standards Committee of the IEEE Computer Society Approved 9 November 2010 IEEE-SA

3、 Standards Board Abstract: This amendment specifies the mechanism for the support of bridging of IEEE 802.20 networks. Keywords: 802.20, bridging The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2010 by the Institute of Electrical and

4、Electronics Engineers, Inc. All rights reserved. Published 19 November 2010. Printed in the United States of America. IEEE and 802 are registered trademarks in the U.S. Patent +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtai

5、ned through the Copyright Clearance Center. Introduction This introduction is not part of IEEE Std 802.20b-2010, IEEE Standard for Local and metropolitan area networksVirtual Bridged Local Area NetworksAmendment 15: Bridging of IEEE 802.20. This document amends IEEE Std 802.1Q-2005 to support bridgi

6、ng of the IEEE 802.20 medium access control. Notice to users Laws and regulations Users of these documents should consult all applicable laws and regulations. Compliance with the provisions of this standard does not imply compliance to any applicable regulatory requirements. Implementers of the stan

7、dard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights This document is copyr

8、ighted by the IEEE. It is made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making this document available f

9、or use and adoption by public authorities and private users, the IEEE does not waive any rights in copyright to this document. Updating of IEEE documents Users of IEEE standards should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from

10、time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. In order to determine whether a given document is the current edi

11、tion and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Standards Association web site at http:/ieeexplore.ieee.org/xpl/standards.jsp, or contact the IEEE at the address listed previously. For more information about the IEEE Standards Associatio

12、n or the IEEE standards development process, visit the IEEE-SA web site at http:/standards.ieee.org. iv Copyright 2010 IEEE. All rights reserved. Errata Errata, if any, for this and all other standards can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/updates/errata/index.h

13、tml. Users are encouraged to check this URL for errata periodically. Interpretations Current interpretations can be accessed at the following URL: http:/standards.ieee.org/reading/ieee/interp/ index.html. Patents Attention is called to the possibility that implementation of this amendment may requir

14、e use of subject matter covered by patent rights. By publication of this amendment, no position is taken with respect to the existence or validity of any patent rights in connection therewith. A patent holder or patent applicant has filed a statement of assurance that it will grant licenses under th

15、ese rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Other Essential Patent Claims may exist for which a statement of assurance has not been received. Th

16、e IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance

17、, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this amendment are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained

18、 from the IEEE Standards Association. v Copyright 2010 IEEE. All rights reserved. vi Copyright 2010 IEEE. All rights reserved. Participants At the time this amendment was submitted to the IEEE-SA Standards Board for approval, the Working Group had the following membership: Mark Klerer, Chair Radhakr

19、ishna Canchi, Vice Chair Nancy Bravin Kazuhito Ishida Francis OBrien James Ragsdale Ajay Rajkumar Jerry Upton The following members of the individual balloting committee voted on this amendment. Balloters may have voted for approval, disapproval, or abstention. Thomas Alexander Butch Anton Davide To

20、daro Boscolo Nancy S. Bravin William Byrd Peter J. Calderon Radhakrishna Canchi James Carlo Juan Carreon Keith Chow Charles Cook Todor Cooklev Russell Dietz Thomas Dineen Carlo Donati M. Epstein C. Fitzgerald Ignacio Marin Garcia Pieter-Paul Giesberts Arnold Greenspan Randall Groves C. Guy Victor Ho

21、u Akio Iso Atsushi Ito Raj Jain Jaehyuk Jang Anthony Jeffree Shinkyo Kaku Piotr Karocki Stuart J. Kerry Yongbum Kim Mark Klerer Joseph Kwak David Landry Juan L. Lazaro Jan-Ray Liao William Lumpkins G. Luri Elvis Maculuba Gary Michel Apurva Mody Rick Murphy Nabil Nasser Michael S. Newman Chris Osterl

22、oh Satoshi Oyama Glenn Parsons Venkatesha Prasad James Ragsdale Maximilian Riegel Robert Robinson Benjamin Rolfe Herbert Ruck Randall Safier Osman Sakr Bartien Sayogo Gil Shultz Kapil Sood Amjad Soomro Manikantan Srinivasan Thomas Starai Walter Struppler Mark Sturza Mark-Rene Uchida Jerry Upton Scot

23、t Valcourt Dmitri Varsanofiev Prabodh Varshney Karl Weber Oren Yuen When the IEEE-SA Standards Board approved this amendment on 9 November 2010, it had the following membership: Robert M. Grow, Chair Richard H. Hulett, Vice Chair Steve M. Mills, Past Chair Judith Gorman, Secretary Karen Bartleson Vi

24、ctor Berman Ted Burse Clint Chaplin Andy Drozd Alexander Gelman Jim Hughes Young Kyun Kim Joseph L. Koepfinger* John Kulick David J. Law Hung Ling Oleg Logvinov Ted Olsen Ronald C. Petersen Thomas Prevost Jon Walter Rosdahl Sam Sciacca Mike Seavey Curtis Siller Don Wright *Member Emeritus Also inclu

25、ded are the following nonvoting IEEE-SA Standards Board liaisons: Satish Aggarwal, NRC Representative Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Catherine Berger IEEE Standards Project Editor Michael Kipness IEEE Standards Program Manager, Technical Program Development

26、 vi Copyright 2010 IEEE. All rights reserved. Contents 2. Normative references 2 6. Support of the MAC Service 2 6.7 Support of the Internal Sublayer Service by specific MAC procedures 2 6.7.2 Support by IEEE Std 802.20 (MBWA) 2 Annex A (normative) PICS proforma. 4 vii Copyright 2010 IEEE. All right

27、s reserved. IEEE Standard for Local and metropolitan area networks Virtual Bridged Local Area Networks Amendment 15: Bridging of IEEE 802.20 IMPORTANT NOTICE: This standard is not intended to ensure safety, security, health, or environmental protection. Implementers of the standard are responsible f

28、or determining appropriate safety, security, environmental, and health practices or regulatory requirements. This IEEE document is made available for use subject to important notices and legal disclaimers. These notices and disclaimers appear in all publications containing this document and may be f

29、ound under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Documents.” They can also be obtained on request from IEEE or viewed at http:/standards.ieee.org/IPR/disclaimers.html. Editorial Note The editing instructions contained in this amendment define how to mer

30、ge the material contained therein into the existing base standard and its amendments to form the comprehensive standard. The editing instruction are shown in bold italics. Three editing instructions are used: change, delete, and insert. Change is used to make a change to existing material. The editi

31、ng instruction specifies the location of the change and describes what is being changed. Changes to existing text may be clarified using strikeout markings to indicate removal of old material, and underscore markings to indicate addition of new material). Delete removes existing material. Insert add

32、s new material without changing the existing material. Insertions may require renumbering. If so, renumbering instructions are given in the editing instruction. Editing instructions, change markings, and this NOTE will not be carried over into future editions because the changes will be incorporated

33、 into the base standard. Changes are applied to the base text of IEEE Std 802.1Q-2005, as modified by those amendments that have been approved, but not incorporated into the base text of the standard, at the time that this amendment was approved, namely (in chronological order) IEEE Std 802.1ad, IEE

34、E Std 802.1ak, IEEE Std 802.1ag, IEEE Std 802.1ah, IEEE Std 802.1Q-2005/Cor 1, IEEE Std 802.1ap, IEEE Std 802.1Qaw, IEEE Std 802.1Qay, IEEE Std 802.1aj, IEEE Std 802.1Qav, and IEEE Std 802.1Qat. 1 Copyright 2010 IEEE. All rights reserved. IEEE Std 802.20b-2010 IEEE Standard for Local and metropolita

35、n area networksVirtual Bridged Local Area Networks Amendment 15: Bridging of IEEE 802.20 2. Normative references Insert the following new reference into Clause 2: IEEE Std 802.20, IEEE Std for Local and Metropolitan Area NetworksPart 20: Air Interface for Mobile Broadband Wireless Access Systems Sup

36、porting Vehicular MobilityPhysical and Media Access Control Layer Specification.1,26. Support of the MAC Service 6.7 Support of the Internal Sublayer Service by specific MAC procedures Insert the following as new subclause 6.7.2: 6.7.2. Support by IEEE Std 802.20 (MBWA) 6.7.2.1 Support by Wideband m

37、ode of IEEE Std 802.20 (MBWA) The Mobile Broadband Wireless Access Method for the IEEE 802.20 Wideband Mode is specified in 5.4 and Clause 6 through Clause 17 of IEEE Std 802.20. Clause 8 of the standard specifies the Wideband Mode Lower MAC Layer Frame structure and protocol procedures. Clause 7 sp

38、ecifies the Radio Link Sublayer protocol and Clause 6 defines the Services Sublayer of the Wideband Mode. Clause 11 defines the Connection Control Plane, which controls the state of the air-link by managing the states of individual Lower MAC Layer protocols, and by providing individual Lower MAC Lay

39、er protocols with operating parameters. The Basic Packet Consolidation Protocol (8.2 of IEEE Std 802.20) provides packet consolidation on the transmit side and provides packet de-multiplexing on the receive side. It provides an interface for the Radio Link Sublayer to transport user information from

40、 the Services Sublayer. For packets to be transmitted over the air interface (wireless medium) either from the Access Node (AN) or Access Terminal (AT), the Lower MAC Sublayer shall accept Radio Link Sublayer data and control packets and shall generate Lower MAC Sublayer control packets of its own.

41、For packets leaving the air interface (wireless medium) for the AN or AT, the Lower MAC Sublayer shall de-multiplex the received packets and shall deliver the payload to the Radio Link Sublayer. The Radio Link Sublayer shall deliver the payload to the Services Sublayer which includes support for dif

42、ferent IEEE802.3 frame based protocols. 6.7.2.1.1 Support for Internal Sublayer Service under Wideband Mode of IEEE Std 802.20 The destination_address, source_address, mac_service_data_unit, and user_priority parameters of the M_UNITDATA primitive are encoded as described in 6.6.2. The value of oper

43、PointToPointMAC (6.6.3) shall be TRUE. The value of MAC_Enabled shall be determined by the procedure described in 6.6.2. 1IEEE publications are available from the Institute of Electrical and Electronics Engineers, Inc., 445 Hoes Lane, Piscataway, NJ 08854, USA (http:/standards.ieee.org/). 2The IEEE

44、standards or products referred to in this clause are trademarks of the Institute of Electrical and Electronics Engineers, Inc. 2 Copyright 2010 IEEE. All rights reserved. IEEE Std 802.20b-2010 IEEE Standard for Local and metropolitan area networksVirtual Bridged Local Area Networks Amendment 15: Bri

45、dging of IEEE 802.20 After the IEEE 802.20 AT has registered with the AN, authenticated, and performed capabilities negotiation, and after the stream is established to carry IEEE 802frames, then the value of the MAC_Operational parameter shall be determined by the procedure described in 6.6.2. Befor

46、ehand, the value of MAC_Operational shall be FALSE. Frame size limits are determined by IEEE Std 802.3. 6.7.2.2 Support by 625k-MC mode of IEEE Std 802.20 (MBWA) The Mobile Broadband Wireless Access Method for 625k-MC mode is specified in 5.5, Clause 18 through Clause 31, and Annex A of IEEE Std 802

47、.20. Clause 19 of the standard specifies 625k-MC Mode MAC Frame structure. Clause 23 specifies the MAC Protocol Sublayer function to implement the 625k-MC mode MAC service. Clause 25 specifies the L3 protocol and Clause 26 defines all the primitives used in 625k-MC Mode. The L3 protocol layer is mad

48、e up of components with distinct roles in supporting a connection across the air interface. The L3 Connection Management (CM) module provides an application level interface to the higher layer. The L3 protocol creates logical connections to transport the higher layer L4 data packets. The L3 Registra

49、tion Management (RM) module takes the L4 data packets provided by the higher layer (through L3 CM) and converts them into a form that can be sent over the air interface. On the receiving side, L3 RM converts packets received from the air interface back into network packets before giving them to L3 CM. Clause 26 defines the higher layer to L3 CM Interface Primitives for the service access point that shall be provided by L3 CM for the use of the higher layer. Clause 26 defines L3 CM to L4 Interface Primitives for the service access point pro