ANSI EIA-364-30A-2002 Capacitance Test Procedure for Electrical Connectors and Sockets《电连接器和插座的电容试验程序》.pdf

《ANSI EIA-364-30A-2002 Capacitance Test Procedure for Electrical Connectors and Sockets《电连接器和插座的电容试验程序》.pdf》由会员分享，可在线阅读，更多相关《ANSI EIA-364-30A-2002 Capacitance Test Procedure for Electrical Connectors and Sockets《电连接器和插座的电容试验程序》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 EIA STANDARD TP-30A Capacitance Test Procedure for Electrical Connectors and Sockets EIA-364-30A (Revision of EIA-364-30) APRIL 2002 ELECTRONIC COMPONENTS, ASSEMBLIES & MATERIALS ASSOCIATION THE ELECTRONIC COMPONENT SECTOR OF THE ELECTRONIC INDUSTRIES ALLIANCE EIA-364-30A ANSI/EIA-364-30A-2002 Appr

2、oved: April 22, 2002 Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE EIA Engineering Standards and Publications are designed to serve the public inte

3、rest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publicat

4、ions shall not in any respect preclude any member or nonmember of EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than EIA members, whether the standar

5、d is to be used either domestically or internationally. Standards and Publications are adopted by EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, EIA does not assume any liability to any patent owner, nor does it assume any obligation whatever t

6、o parties adopting the Standard or Publication. This Standard is based upon the major technical content of International Electrotechnical Commission standard 512-9, test 22a, capacitance, 1992-04, second edition. It conforms in all essential respects with this IEC standard. This Standard does not pu

7、rport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standa

8、rds Proposal Number 3988-A, formulated under the cognizance of the CE-2.0 National Connector Standards Committee.) Published byELECTRONIC INDUSTRIES ALLIANCE 2002 Technology Strategy & Standards Department 2500 Wilson Boulevard Arlington, VA 22201 PRICE: Please refer to the current Catalog of EIA El

9、ectronic Industries Alliance Standards and Engineering Publications or call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) All rights reserved Printed in U.S.A. Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under lic

10、ense with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-PLEASE! DON”T VIOLATE THE LAW! This document is copyrighted by the EIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through en

11、tering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5704 or call U.S.A. and Canada 1-800-854-7179, International (303) 397-7956 Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under li

12、cense with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-i CONTENTS

13、 Clause Page 1 Introduction 1 1.1 Scope 1 1.2 Object . 1 1.3 Definitions 1 2 Test resources . 1 2.1 Equipment 1 2.2 Fixture 2 3 Test specimen . 2 3.1 Description . 2 4 Test procedure 2 5 Details to be specified 3 6 Test documentation 3 Copyright Electronic Components, Assemblies & Materials Associat

14、ion Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ii (This page left blank) Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or netw

15、orking permitted without license from IHS-,-,-EIA-364-30A Page 1 TEST PROCEDURE NO. 30A CAPACITANCE TEST PROCEDURE FOR ELECTRICAL CONNECTORS AND SOCKETS (From EIA Standards Proposal No. 3988-A, formulated under the cognizance EIA CE-2.0 Committee on National Connector Standards, and previously publi

16、shed in EIA-364-30.) 1 Introduction 1.1 Scope This procedure applies to electrical connectors and sockets. 1.2 Object This standard describes a test method to measure capacitance from 1 kHz to 1 MHz. 1.3 Definition That property of a system of conductors and dielectrics which permits the storage of

17、electricity when potential differences exist between the conductors. Its value is expressed as the ratio of the electrostatic charge on a conductor to the potential difference between the conductors required to maintain that charge. 2 Test resources 2.1 Equipment Capacitance shall be measured with a

18、 capacitance meter or bridge that will ensure an accuracy of 0.5% of indicated value + 0.2 picofarad. The sum of the peak ac and dc voltages shall not exceed the voltage rating of the specimen. The test frequency shall be 1 kHz 1% or 1 MHz 1%, (1 kHz 1% is preferred), unless otherwise specified in t

19、he referencing document. 3 Test specimen The test specimen shall consist of a connector (may be mated or unmated), or socket according to the referencing document. Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproducti

20、on or networking permitted without license from IHS-,-,-EIA-364-30A Page 2 4 Test procedure 4.1 Capacitance shall be measured at the specified frequency using the following configurations. 4.1.1 Between one contact and ground with the following parts connected to ground by the lowest impedance path:

21、 all other contacts, all metal parts, the mounting plate. 4.1.2 Between any two adjacent contacts, the following parts all being connected to ground at a common point: all other contacts, all metal parts, the mounting plate. NOTE When measuring pin-to-pin capacitance (crosstalk capacitance) in a con

22、nector containing filter elements the shell of the connector shall be terminated to the bridge guard. 4.1.3 Any other point or operating condition, as specified in the referencing document. 4.2 The test lead capacitance shall be subtracted from the reading. 5 Details to be specified The following de

23、tails shall be specified in the referencing document: 5.1 Initial measurements and conditions, if other than standard atmospheric conditions. 5.2 Preparation of the specimen 5.3 Specimen description and measurement points 5.4 Value of the measuring frequency 5.5 Any special fixture requirements 5.6

24、Magnitude of polarizing voltage and/or magnitude of ac rms test signals Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-EIA-364-30A Page 3 6 Documentation D

25、ocumentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Test equipment used, and date of last and next calibration 6.3 Ambient temperature and humidity 6.4 Values and observations 6.5 Name of operator and date of test Copyright Elec

26、tronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for Resal

27、eNo reproduction or networking permitted without license from IHS-,-,-EIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electroni

28、c Industries Alliance Technology Strategy & Standards Department Publications Office 2500 Wilson Blvd. Arlington, VA 22201 FAX: (703) 907-7501 Document No. Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Claus

29、e Number and/or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Copyright Electronic Components, Assemblies & Materials Association Reproduce

30、d by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from I

31、HS-,-,-Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Electronic Components, Assemblies & Materials Association Reproduced by IHS under license with ECA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-