ANSI ASTM F2765-2014 Standard Specification for Total Lead Content in Synthetic Turf Fibers.pdf

《ANSI ASTM F2765-2014 Standard Specification for Total Lead Content in Synthetic Turf Fibers.pdf》由会员分享，可在线阅读，更多相关《ANSI ASTM F2765-2014 Standard Specification for Total Lead Content in Synthetic Turf Fibers.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、Designation: F2765 14 An American National StandardStandard Specification forTotal Lead Content in Synthetic Turf Fibers1This standard is issued under the fixed designation F2765; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification applies to the maximum content oflead in fibers used in synthetic turf.1.1.1 This specific

3、ation outlines a test method for samplepreparation and a test method for analyzing the total leadcontent in synthetic turf fibers.1.1.2 This specification outlines guidelines for reportingtotal lead content in synthetic turf fibers.1.2 This specification applies only to synthetic turf fibersmanufact

4、ured after Sept. 1, 2009.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this s

5、tandard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2E1613 Test Method for Determination of Lead by Induc-tively Coupled Plasma Atomic Emission Spectrometry(ICP-AES), Flame Ato

6、mic Absorption Spectrometry(FAAS), or Graphite Furnace Atomic Absorption Spec-trometry (GFAAS) Techniques2.2 ISO/IEC Standard:3ISO/IEC 17025 General Requirements for the Competenceof Testing and Calibration Laboratories2.3 U.S. EPA Standards:4EPA Method 3052 Microwave Assisted Acid Digestion ofSilic

7、eous and Organically Based Matrices - Modified,SW846, Test Methods for Evaluating Solid Waste3. Terminology3.1 Definitions:3.1.1 synthetic turf fiber, nextruded fiber used to simulategrass blades in a tufted, knitted, or woven turf fabric.3.1.2 total lead content, nquantity of lead in all formsmeasu

8、red by appropriate analytical technique and reported asmg/kg (ppm).4. Acceptable Level4.1 A representative sample of fiber shall be tested by thetest method(s) described in Section 5 of this specification. Thetotal lead content measured shall be less than 100 mg/kg(ppm).4.2 Synthetic turf fibers sha

9、ll be tested at such quantityintervals as to ensure continuing compliance with the require-ment in 4.1.5. Test Methods5.1 Laboratory QualificationThe testing shall be con-ducted by an ISO/IEC 17025 accredited environmental labo-ratory.5.2 Preparation of the SamplePrepare sample(s) as out-lined in EP

10、A Method 3052 with the temperature modified from180 6 5C to 210 6 10C.5.3 Analysis of Sample:5.3.1 Analyze sample(s) prepared in 5.2 for lead usinginductively coupled plasma-atomic emission spectroscopyICP-AES or atomic absorption spectrometry (AAS) as out-lined in Test Method E1613.5.3.2 Report tot

11、al lead content as mg/kg (ppm).6. Report6.1 Record the following information:6.1.1 Fiber identification, such as lot and color numbers.1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommit

12、tee F08.65 on Artificial Turf Surfaces and Systems.Current edition approved Sept. 1, 2014. Published October 2014. Originallyapproved in 2009. Last previous edition approved in 2009 as F2765 09. DOI:10.1520/F2765-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM

13、 Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Un

14、ited States Environmental Protection Agency (EPA), ArielRios Bldg., 1200 Pennsylvania Ave., NW, Washington, DC 20460, http:/www.epa.gov/waste/hazard/testmethods/index.htm.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.1.2 Date samp

15、led,6.1.3 Method used,6.1.4 Date tested, and6.1.5 Total lead content (mg/kg or ppm).7. Keywords7.1 lead; synthetic turf; synthetic turf fibersAPPENDIX(Nonmandatory Information)X1. APPENDIXX1.1 According to the U.S. Consumer Product Safety Com-mission in a release dated July 30, 2008 from the Office

16、ofInformation and Public Affairs: The U.S. Consumer ProductSafety Commission (CPSC) staff released its evaluation ofvarious synthetic athletic fields. The evaluation concludes thatyoung children are not at risk from exposure to lead in thesefields.ASTM International takes no position respecting the

17、validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is

18、subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Head

19、quarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This sta

20、ndard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 142