ANSI American Society of Sanitary Engineering SERIES 13000-2015 Service Plumber and Residential Mechanical Service Technician Professional Qualifications Standard.pdf

《ANSI American Society of Sanitary Engineering SERIES 13000-2015 Service Plumber and Residential Mechanical Service Technician Professional Qualifications Standard.pdf》由会员分享，可在线阅读，更多相关《ANSI American Society of Sanitary Engineering SERIES 13000-2015 Service Plumber and Residential Mechanical Service Technician Professional Qualifications Standard.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、Service Plumber and Residential Mechanical Service Technician Professional Qualifications Standard ASSE/IAPMO/ANSI Series 13000 ASSE Board Approved: January 2015 ANSI Approved: February 2015 ASSE International An American National StandardASSE/IAPMO/ANSI Series 13000 Professional Qualifications Stan

2、dard i Issued: February 2015 Copyright Information iii Foreword v Professional Qualifications Standards Committee vi Series 13000 Working Group . vii Standard #13010 . 1 Professional Qualifications Standard for the Service Plumber 10-1.1 Scope . 1 10-1.2 Purpose 1 10-1.3 Limitations . 1 10-1.4 Refer

3、ence and Industry Standards . 1 10-2.1 General Knowledge 1 10-2.2 Product Knowledge 2 10-2.3 Product Installation Knowledge . 2 10-2.4 System Knowledge . 2 10-2.5 Documenting and Recording . 3 10-3.1 Terminology . 3 10-3.2 Certification of the Service Plumber . 3 Standard #13020 4 Professional Quali

4、fications Standard for the Residential Mechanical Service T echnician 20-1.1 Scope 4 20-1.2 Purpose 4 20-1.3 Limitations . 4 20-1.4 Reference and Industry Standards 4 20-2.1 General Knowledge 4 20-2.2 Product Knowledge 4 20-2.3 Product Installation Knowledge . 5 20-2.4 System Knowledge . 5 20-2.5 Do

5、cumenting and Recording . 5 20-3.1 Terminology . 6 20-3.2 Certification of the Residential MechanicalService T echnician . 6 Appendix A . 7 References and Abbreviations Appendix B . 8 Vocabulary and Definitions TABLE OF CONTENTS Service Plumber and Residential Mechanical Service T echnician Professi

6、onal Qualifications Standardii ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard Issued: February 2015ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard iii Issued: February 2015 ASSE International Mokena, Illinois Copyright 2015 All rights reserved. COPYRIGHT INFORMAT

7、ION Neither this standard, nor any portion thereof, may be reproduced without the written consent of ASSE International. Organizations wishing to adopt or list any ASSE standard should print the ASSE standard number on the cover page first and in equal or larger type to that of the adopting or listi

8、ng organization. Service Plumber and Residential Mechanical Service T echnician Professional Qualifications Standardiv ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard Issued: February 2015ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard v Issued: February 2015 FORE

9、WORD This foreword shall not be considered a part of the standard. However, it is offered to provide background information. This is the first edition of ASSE/IAPMO/ANSI Series 13000, Service Plumber and Residential Mechanical Service T echnician Professional Qualifications Standard. ASSE Internatio

10、nal is dedicated to the preservation of public health and safety through the use of proper plumbing and piping practices, and approved materials. In the spirit of its motto, “Prevention Rather Than Cure,” ASSEs mission is to continually improve the performance, reliability and safety of plumbing sys

11、tems. The International Association of Plumbing and Mechanical Officials (IAPMO) has been protecting the publics health and safety, and supporting sustainability and emerging technology for more than 80 years by working in concert with government and industry to implement comprehensive plumbing and

12、mechanical systems around the world. With the escalation of green building and the rapid emergence of sustainable technologies and construction practices, ASSE and IAPMO recognized the need to establish a level of competency necessary for the installation and inspection of sustainable plumbing and m

13、echanical systems and products to protect public health, safety and the environment. As such, the Series 13000 working group was established to develop this Service Plumber and Residential Mechanical Service T echnician Professional Qualifications Standard. The Series 13000 institutes a minimum leve

14、l of practical experience, and the plumbing service and residential mechanical service knowledge required in order for an individual to demonstrate the required level of competency. This voluntary, consensus standard was promulgated in accordance with procedures developed by the American National St

15、andards Institute (ANSI). Service Plumber and Residential Mechanical Service T echnician Professional Qualifications Standardvi ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard Issued: February 2015 Donald Summers Jr., ChairmanUA Local 562St. Louis, MO Kenneth Borski UA Local 68 JAC

16、Houston, TX Laurence T . ColemanUA Local 597Mokena, IL Dana ColomboNational Inspection T esting & Certification (NITC)Metairie, LA Robert L. CrossUA Local 68 JACHouston, TX James KendzelASPEDes Plaines, IL Edward LyczkoCleveland Clinic - RetireeCleveland, OH Matthew Marciniak (non-voting)IAPMOMilwau

17、kee, WI Douglas MarianUA Local 78Los Angeles, CA Barry Pines, CPDC & R PlumbingShelby T ownship, MI Richard J. ProspalProspal Consulting Services Inc.Brunswick, OH Philip RoachSolarc Architecture & Engineering, Inc.Portland, OR Kenneth SchneiderSprinkler Fitters Local 268St Louis, MO Jason ShankUA L

18、ocal 55Cleveland, OH Stephen SilberCeres, CA Jaime ValdiviaNational Inspection T esting & Certification (NITC)Los Angeles, CA Marianne Waickman (non-voting) ASSE InternationalMokena, IL ASSE PQ STANDARDS COMMITTEE Service Plumber and Residential Mechanical Service T echnician Professional Qualificat

19、ions StandardASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard vii Issued: February 2015 Douglas A. Marian, ChairmanUA Local 78 Los Angeles, CA Paul BakerPITC & UA Local 98Detroit, MI Thomas G. BigleyUnited AssociationAnnapolis, MD Matthew King IIIVeterans Health AdministrationBerwic

20、k, PA Scott HamiltonASSE InternationalMokena, ILJohn A. ParizekMinneapolis Plumbers JATCMinneapolis, MN Dwight PerkinsIAPMOOntario, CA Barry Pines, CPDC & R PlumbingShelby T ownship, MI Jason ShankUA Local 55Cleveland, OH Donald Summers Jr.UA Local 562St. Louis, MO Marianne WaickmanASSE Internationa

21、l Mokena, IL ASSE SERIES 12000 WORKING GROUP Service Plumber and Residential Mechanical Service T echnician Professional Qualifications Standardviii ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard Issued: February 2015ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standar

22、d 1 Issued: February 2015 ASSE SERIES 13000 STANDARD #13010 Professional Qualifications Standard for the Service Plumber 10-1.1 Scope This standard applies to an individual who services, maintains and repairs plumbing systems. 10-1.2 Purpose The purpose of this standard is to provide minimum perform

23、ance criteria, identified by industry consensus, for service plumbing to ensure compliance with the referenced standards in Appendix A. 10-1.3 Limitations This standard applies to service, maintenance and repair of plumbing systems only. 10-1.4 Reference and Industry Standards and Codes See Appendix

24、 A. 10-2.1 General Knowledge 10-2.1.1 The service plumber shall be able to identify and show knowledge of the applicable laws, codes, rules, listing agencies and regulations from the federal, state and local levels pertaining to plumbing systems and the ASSE/IAPMO/ANSI Series 13000. 10-2.1.2 The ser

25、vice plumber shall be able to identify the proper procedures to notify all of the Authorities Having Jurisdiction (AHJ) and be able to effectively communicate with the customer. 10-2.1.3 The service plumber shall be able to demonstrate knowledge of the following concepts: a) Acceptance testing (roug

26、h-in and final inspections) b) Accessibility requirements c) Basic electricity d) Cross-connection and backflow protection e) Customer service f) Drain cleaning g) Drain, waste and vent systems h) Effective communication i) Fixture, appliance and equipment installation/ operation j) Fixture, applian

27、ce and equipment maintenance and repair k) Fuel gas systems l) Green systems 1) Alternative water supply systems 2) Black water systems 3) Gray water systems 4) Rainwater harvesting systems 5) Reclaimed water systems 6) Solar thermal systems m) Hangers and fasteners n) Job safety o) Local plumbing a

28、nd health codes p) Location and documentation of underground utilities q) Plan interpretation r) Pumps s) Sanitary and storm sewer (public/private) t) Storm water systems u) Valve and pipe repair v) Water audit w) Water heating equipment x) Water supply systems y) Water treatment2 ASSE/IAPMO/ANSI Se

29、ries 13000 Professional Qualifications Standard Issued: February 2015 10-2.2 Product Knowledge The service plumber shall be able to identify and describe the proper operating principles and performance characteristics of the plumbing and related systems, and identify the following components: a) App

30、liances b) Appurtenances c) Backflow protection d) Basic electrical and control systems e) Drain, waste and vent systems f) Equipment (pumps, water heaters, etc.) g) Fixtures h) Fuel gas systems i) Green systems 1. Alternative water supply systems 2. Black water systems 3. Gray water systems 4. Rain

31、water harvesting systems 5. Reclaimed water systems 6. Solar thermal systems j) Hangers and pipe supports k) Pipe, tube and fittings l) Pumps m) Sanitary and storm sewer (public/private) n) Storm water systems o) Underground utilities p) Valves q) Water heating equipment r) Water supply (public/priv

32、ate) s) Water treatment equipment 10-2.3 Product Installation Knowledge 10-2.3.1 The service plumber shall be able to identify and describe the proper installation requirements for plumbing systems pertaining to: a. Applicable governmental requirements b. Applicable plumbing and mechanical codes and

33、 standards c. Manufacturers installation instructions 10-2.4 System Knowledge 10-2.4.1 The service plumber shall be able to diagnose, service, maintain, repair and install plumbing systems. 10-2.4.2 The service plumber shall be able to identify and describe the appropriate use of the following: a) A

34、ppliances b) Approved materials c) Appurtenances d) Backflow protection e) Basic electric and control systems f) Drain systems g) Equipment (pumps, water heaters, etc.) h) Fixtures i) Fuel gas systems j) Green systems 1. Alternative water supply systems 2. Black water systems 3. Gray water systems 4

35、. Rainwater harvesting systems 5. Reclaimed water systems 6. Solar thermal systems k) Sewage systems l) Storm water systems m) Underground utilities n) Venting systems o) Water supply 10-2.4.3 The service plumber shall be able to describe the precautions and hazards associated with the following: a)

36、 Cross-connections b) Customer safety c) Drainage and sewer systems d) Fuel gas systems e) Hangers and supports f) Job safety g) Pipe identification, joining, sizing and location h) Structural and decorative changes i) Underground utilities, identifying, locating and documenting j) Venting systems k

37、) Water distribution l) Water heater systems m) Water treatment 10-2.4.4 The service plumber shall be able to demonstrate knowledge of the following: a) Drain cleaning b) Drain, waste and vent systems c) Fuel gas systems d) Green systems 1. Alternative water supply systems 2. Black water systems 3.

38、Gray water systems 4. Rainwater harvesting systems 5. Reclaimed water systems 6. Solar thermal system equipment and panels e) Plumbing fixtures equipment, appurtenances and appliances f) Pumps g) Safety h) Sewer systems i) Storm water systems j) T roubleshooting, maintenance and repairASSE/IAPMO/ANS

39、I Series 13000 Professional Qualifications Standard 3 Issued: February 2015 k) Underground utilities, identifying, locating and documenting l) Water distribution systems m) Water heating systems n) Water treatment equipment 10-2.4.5 The service plumber shall be able to identify the correct physical

40、locations for the following items: a) Backflow protection assemblies and devices b) Control valves c) Distribution piping d) Drainage and sewer cleanouts, and backwater valves e) Expansion tanks f) Green systems 1. Alternative water supply systems 2. Black water systems 3. Gray water systems 4. Rain

41、water harvesting systems 5. Reclaimed water systems 6. Solar thermal system equipment and panels g) Pipe labeling h) Plumbing fixture rough-in i) Pressure reducing valves j) Storm water systems k) Underground utilities l) Venting systems m) Water hammer arresters n) Water service 10-2.5 Documenting

42、and Recording 10-2.5.1 The service plumber shall have knowledge of the following documentation: a) Acceptance forms b) As-built or record drawings c) Calculations d) Construction documents (plans, specifications and permits) e) Instructions on inspecting, testing, repairing and maintaining the syste

43、m f) Manufacturers installation, operation and maintenance manuals g) Work orders for the contractor and customer h) Warranties and rebates 10-3.1 Terminology The service plumber shall be able to demonstrate a basic working knowledge of all terminology listed in Appendix B. 10-3.2 Certification of t

44、he Service Plumber 10-3.3.1 Eligibility requirements 10-3.3.1.1 A minimum of five (5) years of documented practical experience in the installation, maintenance or repair of plumbing systems. 10-3.3.1.2 Successful completion of a minimum 40-hour training course encompassing all aspects of ASSE Standa

45、rd 13010 and including hands-on practical experience. 10-3.3.1.3 Certification shall include successfully passing a written exam and practical exam encompassing all aspects of ASSE Standard 13010. The written exam must be a minimum of 100 questions with a passing grade of at least 75%. The practical

46、 exam shall include hands-on and/or virtually simulated situations. 10-3.3.1.4 Certification to this standard shall be through a nationally recognized third-party certification agency. 10-3.3.1.5 Certification shall be for a three (3) year period. 10-3.3.2 Recertification of Service Plumbers 10-3.3.

47、2.1 Recertification shall include the successful completion of a minimum 8-hour course encompassing all aspects of ASSE Standard 13010 and successfully passing a written exam that is a minimum of 25 questions with a passing grade of at least 75%. Certification to this standard shall be through a nat

48、ionally recognized third-party certification agency.4 ASSE/IAPMO/ANSI Series 13000 Professional Qualifications Standard Issued: February 2015 ASSE SERIES 13000 STANDARD #13020 Professional Qualifications Standard for the Residential Mechanical Service T echnician 20-1.1 Scope This standard applies t

49、o an individual who services, maintains and repairs residential mechanical systems. 20-1.2 Purpose The purpose of this standard is to provide minimum performance criteria, identified by industry consensus, for residential mechanical service technicians (herein referred to as service technician) to ensure compliance with the referenced standards in Appendix A. 20-1.3 Limitations This standard applies to service, maintenance and repair of residential mechanical systems only. 20-1.4 Reference and Industry Standards and Codes See Appendix A. 20-2.1 General Knowledge 20-2.1.1 The service