AGMA 01FTM9-2001 New opportunities with Molded Gears《浇注齿轮的新时机》.pdf

《AGMA 01FTM9-2001 New opportunities with Molded Gears《浇注齿轮的新时机》.pdf》由会员分享，可在线阅读，更多相关《AGMA 01FTM9-2001 New opportunities with Molded Gears《浇注齿轮的新时机》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、01FTM9New Opportunities with Molded Gearsby: R.E. Kleiss, A.L. Kapelevich and N.J. Kleiss Jr.,Kleiss Gears, Inc.TECHNICAL PAPERAmerican Gear ManufacturersAssociationNew Opportunities with Molded GearsRoderick E. Kleiss, Alexander L. Kapelevich and N. Jack Kleiss Jr.,Kleiss Gears, Inc.Thestatementsan

2、dopinionscontainedhereinarethoseoftheauthorandshouldnotbeconstruedasanofficialactionoropinion of the American Gear Manufacturers Association.AbstractMolded gearing includes plastic and powder metal injection molded gears as well as powder metal sintered gears.Near-net forged gears may also share som

3、e unique similarities and opportunities as well. This type of manufacturingofferssomeparticularlyintriguingopportunitiesforthegeardesigner,andalsosomechallengesnotusuallyencounteredwith cut gears. The challenges are often related to the mechanical properties of the material. Proper steel, cut andhar

4、dened correctly, is hard to beat for strength. Ordinary attempts to replace steel gears with the molded variety areusually doomed to failure.On the other hand, molded gears can offer some material properties not achievable with cut gears, including uniqueadvantages in weight, noise, modulus, self-lu

5、brication, magnetism, chemical resistance, and most appealing low cost.Thechallengeistomakethemsurvivethedemandsputuponthem.Forinstance,thermoplasticgears,whenplacedundercontinuoushighload,willmelt.Thisisaphenomenonnotsharedwithanymetalcounterpart.Thegoalmustbetomakeaweakermaterialappearstronger.The

6、uniquetoolsthatareavailabletothemoldedgeardesignerareconcentratedinthemethod of manufacture. When the proper mold is constructed and combined with the optimized molding process, aremarkablyconsistentanduniformgearcanbecontinuouslymanufactured.TheconstructionofthismoldedtoolingcanbealmostcompletelyCA

7、Dbased.Traditionalgearcuttingprocessesarealmostneverusedtodevelopthemoldcavities.Uniquetoothgeometrythatmightbedifficultorevenimpossibletoachievewithcutgearscanbeappliedtomoldedgearsmatter-of-factly.Thispaperwillinvestigatetwotypesofgearsthatwehavedesigned,molded,andtestedinplastic.Thefirst isan asy

8、mmetric mesh, the second isan orbiting transmission. The asymmetric gearshave dissimilar 20_ and 48_pressureangleswhiletheorbitinggearsetworkswitha65_pressureangle.Bothtransmissionshavehigherloadpotentialthan traditional design approaches.CopyrightGe32001American Gear Manufacturers Association1500 K

9、ing Street, Suite 201Alexandria, Virginia, 22314October, 2001ISBN: 1-55589-788-61New Opportunities with Molded gears Rod Kleiss, President, Kleiss Gears Alex Kapelevich, Principal Engineer, Kleiss Gears N. Jack Kleiss Jr., Consultant, Kleiss Engineering Molded gears share some very basic similaritie

10、s with cut metal gears, principally the involute gear shape and a need for precise design, manufacturing, and inspection. They also diverge from cut metal gears in some very significant ways. The design of the gears and mold tool construction usually does not require or employ any traditional gear c

11、utting techniques. Spur gear molds are almost invariably made utilizing a wire Electrical Discharge Machine (EDM) which is capable of producing any 2-dimensional and even some slightly 3-dimensional shapes with surface accuracy on the order of a single micron. Helical cavities are cut using electrod

12、e EDMs. These electrodes can be made with end mills having gear profiles wire EDMd into their cutting edges, or by using high-speed surface generation on a 4-axis CNC mill. The difficulty of using traditional gear cutting techniques is most often due to the required physical geometry of the cavity.

13、Since most molded gears will shrink from the mold, the mold cavity must be adjusted for enlarged base pitch, tooth thickness, major, and minor diameters. Form grinding electrodes is an option, but standard hob generation is almost never suitable. Additionally, very few electrodes will be needed to g

14、enerate the mold cavities. Gear houses tend to shy away from such small jobs that will only infrequently be repeated. Still, the options left open to the molded gear designer are quite extensive To achieve an effective transmission design, every available tool and resource is usually required. First

15、 of all is the design of the gears themselves. As with many design constraints, space is usually at a premium with large expected loads. The danger with molded plastic gears especially is heat. Plastic gears melt, and as temperature increases, their modulus of elasticity decreases and they get even

16、weaker. Constant duty cycles under heavy loading is one of the most difficult designs to achieve successfully with plastic molded gears. Using exotic materials with higher heat capacity brings along its own set of problems. Quite often these materials will be brittle, or difficult to mold accurately

17、, or just too expensive to be cost competitive with high speed gear cutting. Most successful plastic gear designs will be molded with basic engineering thermoplastics such as nylon or acetal. Molded Gear Design One of the biggest opportunities for the molded gear designer is the design of the gears

18、themselves. Since the spur tooling can be generated with wire EDM, any 2-dimensional shape that can be drawn, can usually be produced, and even adjusted mathematically for shrinkage before being cut. There are only 8 variables required to completely describe a symmetrical spur gear mesh design. Figu

19、re 1 is a screen dump of our design approach to this task. 2Figure 1 Typical spur gear design The input data field in the upper left-hand corner of Figure 1 shows the required information to complete this design. For symmetric gears the operating pressure angle will be the same in both directions. T

20、he numbers of teeth in each gear is followed by the tooth thickness of one of the gears. In this case tooth thickness is defined as a non-dimensional ratio to the base pitch of the drive pinion. The outside diameter of both gears is required as well as the wire diameter of the EDM that will cut the

21、cavities. This will cause the tips of each gear to be rounded, which will affect both the contact ratio and the formation of the mating gears root geometry. Finally, either center distance of the mesh or the base pitch is required to physically size the gears. With these minimum inputs the rest of t

22、he gear features are produced by generation from the principal features. In this case, the outside diameters of the gears are designed to 98% of the theoretical maximum diameter possible. A slight undercut is generated by the gear to the pinion. This gives the effect of a bonus tolerance on contact

23、ratio, since the contact ratio will not begin to decrease until the gears have separated beyond the undercut condition. Tooth thickness can be adjusted visually and then checked with traditional methods to assure balanced strength. Working pressure angles can be increased or decreased to optimize an

24、y particular feature. Similar results can be attained with shaper 3cut gears, but accuracy will not be equivalent to the wire EDM, and physical limitations of cutters will limit attainable features. Figure 2 shows some of the possibilities with this method of design. As is readily apparent in Figure

25、 2, design freedom does not necessarily result in good design, but the potential for unique solutions is obvious. Internal as well as external gear sets are equally feasible. Two unique designs utilizing this approach will now be presented. These designs were tooled, molded and tested. Set outer dia

26、meters to .5 of maximum Design all recess action gears Design 12 working pressure angle Design an asymmetric 15/30 pressure angle set Figure 2 Possibilities for unique gear design 4Internal Orbiting Gear Set A constant goal in gearing is to produce higher reduction gear sets with greater torque capa

27、city. One method that has been utilized consists of orbiting a notched wheel about fixed pins, the wheel having one or less fewer indentations than the pins. Therefore, with each orbit of the wheel, the bolt hole pattern cut into its face will advance angularly. An output bolt pattern can couple thi

28、s rotation from the orbiting gear to an output shaft on the reference axis (Figure 3). Transmissions of this design are in production today. They have high load capabilities and high efficiency, but must be machined with very high accuracy to effect smooth torque transfer, and they also must have ex

29、cellent bearing systems. An alternative approach is to design involute gears for the orbiting set rather than use circular arcs. This has the advantage of letting the involute geometry provide for smooth rotary transmission in the low tolerance environment of plastic molding. An additional benefit i

30、s that the torque coupling through involutes would be more effective for plastic and reduce the change of tooth deformation. Utilizing the same approach as for external gears, an internal gear set was designed to orbit a 39 tooth gear about a 40 tooth internal gear. The design is presented in Figure

31、 4. As with external gears, internal designs require only a few variables to completely describe the system. A one tooth difference between driver and driven gear requires a very large working pressure angle to assure clearance outside of the contact area. In this case the working pressure angle was

32、 set at 65 degrees. The largest apparent discrepancy with this design is the less than unity contact ratio of the gears. Although this is true mathematically, the fact is that the gears are really in mesh over a much larger area of engagement than theoretically predicted, given the lower modulus of

33、elasticity of plastic. The resultant actual contact ratio is in effect much greater than 1. The tools were made and the gears were molded as shown in Figure 5. Figure 3 Orbiting gear transmission 5Figure 4 Internal Involute Orbiting Gear A gear tester was constructed to determine the actual load cap

34、acity of the gears and the efficiency. The transmission mounted in that tester is shown in Figure 6. The gear tester consists of a precision DC servomotor driving the transmission into a calibrated hysterisis brake with an attached strain gage load cell on a torque arm to accurately gauge transmitte

35、d torque. Voltages and currents are supplied and monitored with a computerized interface with torque readings and angular position recorded dynamically. Figure 5 Involute Orbiting gears 6Figure 6 Orbiting Transmission Tester Testing on this transmission proved that the gears themselves could not be

36、failed with the available motor torque. Stall torques up to 30 in.-lbs. failed to break the transmission. Efficiency was another story. The use of bushings resulted in efficiency less that 20%. Coupling the input torque through the small motor bushing resulted in early mortality of that motor. Subse

37、quently, ball bearings replaced bushings, the motor was de-coupled, and efficiency raised to over 70%. The conclusion made at the end of this testing was that the bearing system rather that the plastic gears became the weakest link. Further work is continuing to reduce these bearing loads and improv

38、e performance. Asymmetric Gears Another way to increase load capacity of transmissions is to modify the involute geometry. This has been standard practice in sophisticated gear design for many years. The nomenclature describing these types of gear modifications can be quite confusing, with reference

39、 to addendum modification, profile shift, etc., etc. An additional alteration that is very rarely used is to make the gears asymmetric with different profile angles for each side of the tooth. Two sides (profiles) of the gear tooth are functionally different for most gears. The workload on one profi

40、le is significantly higher and/or for longer periods of time then the opposite one. The tooth shape must reflect this functional difference. The general idea of asymmetric teeth is to improve performance (increase load capacity, reduce noise and vibration, etc.) of the main contacting profiles by di

41、nt of degrading the opposite profiles. These opposite profiles are unloaded or slightly loaded and usually work for short duration only. Degree of asymmetry and drive profile selection for asymmetric gears depends on the gear application. If bending stress is an issue then the low-pressure angle pro

42、file is preferable for the drive side (so called “buttress“ teeth), whereas the contact stresses, noise and vibration could be significantly reduced if the drive side has a high-pressure angle. An asymmetric gear set was designed and molded for a lawn sprinkler system. Design and testing of the asym

43、metric gears was 7conducted with comparison to current symmetric gears and the best possible symmetric gears. A summary of the three different design meshes is presented in Figure 7. Pinion Gear Pinion Gear Pinion Gear Drive side pressure angle, deg. 23.194 30 20 Coast side pressure angle, deg. 23.1

44、94 30 48 Operating pitch diameter, in. .1147 .2294 .1147 .2294 .1147 .2294 Drive side base diameter, in. .1054 .2108 .0993 .1986 .1078 .2156 Coast side base diameter, in. .1054 .2108 .0993 .1986 .0767 .1534 Outside diameter, in. .1443 .2538 .1398 .2488 .01352 .2472 Root diameter, in. .859 .195 .0952

45、 .2042 .0968 .2073 Tooth thickness on PD, in. .0205 .0155 .0208 .0152 .0196 .0164 Tooth width, in. .100 .095 .100 .095 .100 .095 Center distance, in. .172 .172 .172 Drive side contact ratio 1.48 1.08 1.157 Coast side contact ratio 1.48 1.08 .933 * maximum material condition profiles, backlashless me

46、sh. Static Finite Element- bending stresses* Current Symmetric Gear Set New High Pressure Angle Set Asymmetric Set Pinion Gear Pinion Gear Pinion Gear Torque (In*lb) 0.10 0.20 0.10 0.20 0.10 0.20 RPM 1,000 500 1,000 500 1,000 500 Stress (psi) Tension Comp- ression Tension Comp- ression Tension Comp-

47、 ression Tension Comp- ression Tension Comp- ression Tension Comp- ression Von Mises 8,178 (100%) 8,692 (100%) 6,761 (100%) 7,897 (100%) 5,350 (65%) 7,540 (87%) 4,878 (72%) 7,010 (89%) 4,070 (50%) 4,937 (57%) 4,660 (69%) 3,510 (44%) Max Principal 8,820 (100%) 7,313 (100%) 5,857 (66%) 5,394 (74%) 4,2

48、90 (49%) 5,057 (69%) Min Principal -8,879 (100%) -8,061 (100%) -8,089 (91%) -7,386 (92%) -5,312 (60%) -4,210 (52%) Load is applied to the drive side of the tooth in the highest point of single tooth contact Material properties: Youngs Modulus = 700,000psi; Poissons ratio= .32 Figure 7 Design compari

49、son tables 8Gears were molded in the three different designs and tested. The results of that testing are presented below: Standard Parts from the Line Peak Torque (oz-in) Comments 1 27.4 Gearbox output gear teeth bent & broken. Final compound gear teeth broken. 2 20.6 Gearbox output gear had some bent teeth. Final compound gear teeth broken. 3 23.0 Gearbox output gear had some bent teeth. Final compound gear teeth broken. 4 24.7 Final compound gear teeth broken. 5 27.3 Gearbox output gear had bent teeth. Final compound gear teeth broken. Avg. 24.6 BASF N2320 - Asymmetric Peak Tor