ABS 109-2016 RULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT.pdf

《ABS 109-2016 RULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT.pdf》由会员分享，可在线阅读，更多相关《ABS 109-2016 RULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT.pdf（1312页珍藏版）》请在麦多课文档分享上搜索。

1、 Notices and General Information RULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT 2016 NOTICES AND GENERAL INFORMATION American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 Copyright 2015 American Bureau of Shipping ABS Plaza 16855 Northchase Drive Housto

2、n, TX 77060 USA Table of Contents part Notices and General Information CONTENTS Introduction . 1 TABLE 1 Applicable Editions of Booklets Comprising 2016 Rules 2 TABLE 2 Division and Numbering of Rules and Guides 2 Rule Change Notice (2016) . 3 TABLE 3 Summary of Changes from the 2015 Rules 3 ii ABSR

3、ULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT .2016 Notices and General Information Introduction 1. The year 2016 edition of the Rules for Building and Classing High-Speed Naval Craft consists of the eight (8) booklets as shown in Table 1. With regard to three booklets, Part 1, Part 2, and P

4、art 7: a) The purpose of the generic title ABS Rules for Conditions of Classification High-Speed Craft (Part 1) is to reflect the expanded contents of PART 1, as a result of including consolidated requirements for “Classification” applicable to all types of and sizes of high-speed craft as specified

5、 in the Foreword to Part 1. Additional specific requirements are contained in Chapters 2 and 3 of Part 1. b) The purpose of the generic title ABS Rules for Materials and Welding of PART 2 is to emphasize the common applicability of the requirements to ABS-classed vessels, other marine structures and

6、 their associated machinery, and thereby make PART 2 more readily a common “PART” of various ABS Rules and Guides, as appropriate. c) The purpose of the generic title ABS Rules for Survey After Construction (Part 7) is to reflect the expanded contents of PART 7, as a result of including consolidated

7、 requirements for “Surveys After Construction” applicable to all types and sizes of vessels, barges and specific shipboard arrangements/systems, etc., as specified in Part 7, Chapter 1, Section 1. 2. The numbering system applied in the Rules is shown in Table 2. 3. The primary changes from the 2015

8、Rules are identified and listed in Table 3. The effective date of the indicated Rule Changes is 1 January 2016, unless specifically indicated otherwise. 4. The effective date of each technical change since 1993 is shown in parenthesis at the end of the subsection/paragraph titles within the text of

9、each Part. Unless a particular date and month are shown, the years in parentheses refer to the following effective dates: (2000) and after 1 January 2000 (and subsequent years) (1996) 9 May 1996 (1999) 12 May 1999 (1995) 15 May 1995 (1998) 13 May 1998 (1994) 9 May 1994 (1997) 19 May 1997 (1993) 11 M

10、ay 1993 5. Until the next edition of the Rules for Building and Classing High-Speed Naval Craft is published, Rule Change Notices and/or Corrigenda, as necessary, will be published on the ABS website www.eagle.org only, and will be available free for downloading. It is not intended to publish hard c

11、opies of future Rule Change Notices and/or Corrigenda to existing Rules or Guides. The consolidated edition of the Rules for Building and Classing High-Speed Naval Craft, which includes Rule Change Notices and/or Corrigenda using different colors for easy recognition, will be published on the ABS we

12、bsite only when RCN and/or Corrigenda are issued. 6. The listing of CLASSIFICATION SYMBOLS AND NOTATIONS is available from the ABS website www.eagle.org for download. ABSRULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT .2016 1 Notices and General Information 2 ABSRULES FOR BUILDING AND CLASSIN

13、G HIGH-SPEED NAVAL CRAFT .2016 TABLE 1 Applicable Editions of Booklets Comprising 2016 Rules Notices and General Information 2016 Part 1: Rules for Conditions of Classification High-Speed Craft 2016* Part 2: Rules for Materials and Welding Rules for Testing and Certification of Materials Rules for W

14、elding and Fabrication 2016* Part 2: Rules for Materials and Welding Aluminum and Fiber Reinforced Plastics (FRP) 2016* Part 2: Rule Requirements for Materials and Welding Supplementary Requirements for Naval Vessels 2000* Part 3: Hull Construction and Equipment 2016 Part 4: Craft Systems and Machin

15、ery 2016 Part 7: Rules for Survey After Construction 2016* * Note: The latest edition of these Rules is to be referred to. These Rules may be downloaded from the ABS website at www.eagle.org, Rules and Guides, Downloads or may be ordered separately from the ABS Publications online catalog at www.eag

16、le.org, Rules and Guides, Catalog. TABLE 2 Division and Numbering of Rules and Guides Division Number Part Part 1 Chapter Part 1, Chapter 1 Section Section 1-1-1 Subsection (see Note 1) 1-1-1/1 Paragraph (see Note 1) 1-1-1/1.1 Subparagraph 1-1-1/1.1.1Item 1-1-1/1.1.1(a) Subitem 1-1-1/1.1.1(a)i) Appe

17、ndix Appendix 1-1-A1or Appendix 1-A1-1 Note: 1 An odd number (1, 3, 5, etc.) numbering system is used for the Rules and Guides. The purpose is to permit future insertions of even-numbered paragraphs (2, 4, 6, etc.) of text and to avoid the necessity of having to renumber the existing text and associ

18、ated cross-references, as applicable, within the Rules and associated process instructions, check sheets, etc. Notices and General Information Rule Change Notice (2016) TABLE 3 Summary of Changes from the 2015 Rules EFFECTIVE DATE 1 July 2015 shown as (1 July 2015) (based on the contract date for ne

19、w construction between builder and Owner) Part/Para. No. Title/Subject Status/Remarks PART 3 Hull Construction and Equipment 3-1-2/Table 2 Material Class or Grade of Structural Members To require the materials for other steering equipment components described in Section 3-2-8 to be of steel in accor

20、dance with the requirements of Part 2, Chapter 1. (Incorporates Notice No. 1) 3-2-7/13 (New) Energy Saving Devices (ESD) (Hull Appendages) To clearly identify design and survey requirements for energy saving devices (ESD) so that the hull welding, material compatibility and hull structural continuit

21、y evaluation during design and survey of these appendages must be assessed to identify any high stress concentrations together with erosion/corrosion spots. (Incorporates Notice No. 1) 3-2-8/1.1 Application To clearly indicate steering equipment other than rudders in the Application section. (Incorp

22、orates Notice No. 1) 3-2-8/1.3 Materials for Rudder, Rudder Stock and Steering Equipment To specify that rudders and other steering equipment are to comply with 3-1-2/Table 2. (Incorporates Notice No. 1) 3-2-13/1.1 General To add requirement for IMO PSPC (Section 3.3.2) and/or IMO PSPC-COT Regulatio

23、ns compliance. (Incorporates Notice No. 1) EFFECTIVE DATE 1 January 2016 shown as (2016) (based on the contract date for new construction between builder and Owner) Part/Para. No. Title/Subject Status/Remarks PART 3 Hull Construction and Equipment 3-2-1/9 Operating Manual To specify that the operati

24、ng manual is to be ABS approved and to clarify the design environmental conditions in association with OE notation. 3-2-8/7.3 Lower Rudder Stocks To remove “K” since material factor (K) is already included in the maximum allowable stress formula. 3-6-1/1 General To reflect the comments from Administ

25、rations and Industry Organizations considered during review of the proposed Testing Guidelines associated with SOLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. 3-6-1/1.3.2 To reflect the comments from Administrations and Industry Organizations considered during review of

26、the proposed Testing Guidelines associated with SOLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. 3-6-1/3.3 Structural Testing To reflect the comments from Administrations and Industry Organizations considered during review of the proposed Testing Guidelines associated wit

27、h SOLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. 3-6-1/5 Testing Methods To reflect the comments from Administrations and Industry Organizations considered during review of the proposed Testing Guidelines associated with SOLAS Chapter II-1, Regulation 11, made during th

28、e IMO MSC and SDC meetings. 3-6-1/7.1.1 Leak Testing To reflect the comments from Administrations and Industry Organizations considered during review of the proposed Testing Guidelines associated with SOLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. ABSRULES FOR BUILDING

29、AND CLASSING HIGH-SPEED NAVAL CRAFT .2016 3 Notices and General Information Part/Para. No. Title/Subject Status/Remarks 3-6-1/7.7 (New) Hydrostatic or Hydropneumatic Tightness Testing To reflect the comments from Administrations and Industry Organizations considered during review of the proposed Tes

30、ting Guidelines associated with SOLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. 3-6-1/9 (New) Alternative Procedure for Strength Testing To reflect the comments from Administrations and Industry Organizations considered during review of the proposed Testing Guidelines as

31、sociated with SOLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. 3-6-1/Table 1 Testing Requirements for Tanks and Boundaries To reflect the comments from Administrations and Industry Organizations considered during review of the proposed Testing Guidelines associated with S

32、OLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. 3-6-1/Table 2 Application of Leak Testing, Coating and Provision of Safe Access for Type of Welded Joints To reflect the comments from Administrations and Industry Organizations considered during review of the proposed Testi

33、ng Guidelines associated with SOLAS Chapter II-1, Regulation 11, made during the IMO MSC and SDC meetings. PART 4 Craft Systems and Machinery 4-1-1/Table 3 Certification Details Electrical and Control Equipment To provide the option of Tier 4 certification. 4-3-4/7.7.2 Keyless Coupling To align the

34、requirements with industry practice. 4-6-4/5.5.5(b) Emergency Bilge Suction To specify an adequate flow to the emergency bilge pump to maintain its discharge capacity. 4-6-4/13.5.3(b) Remote Means of Closure To align the requirements with the latest IEC requirements. 4-6-4/Table 3 Pipe Joint Limitat

35、ions for Fuel Oil Piping To provide requirements for limitations of Type G flanges. 4-6-5/Table 3 Pipe Joint Limitations for Cooling Water Systems To provide requirements for limitations of Type G flanges. 4-6-5/Table 5 Pipe Joint Limitations for Starting Air Systems To provide requirements for limi

36、tations of Type G flanges. 4-6-6/Table 2 Pipe Joint Limitations for Pneumatic Systems To provide requirements for limitations of Type G flanges. 4-7-1/23.3.3(c) Cables To align the requirements with the latest IEC requirements. 4-8-1/7.1 General To align the requirements with the latest IEC requirem

37、ents. 4-8-1/7.3.1 Low Voltage To align the requirements with the latest IEC requirements. 4-8-2/9.13.2 Short-circuit Protection To specify that if generators are fitted with differential protection systems, then they need not simultaneously have a separate instantaneous trip function. 4-8-3/3.15.9 D

38、ielectric Strength Test To align the requirements with the latest IEC requirements. 4-8-3/5.15.3 Dielectric Strength Test To align the requirements with the latest IEC requirements. 4-8-3/8.5.10 Electrical Protection To clarify overvoltage, overcurrent and short circuit protection requirements of th

39、e semiconductor converter and the semiconductor devices associated with or contained within. To reduce the proscribed protection requirements is to allow equipment makers to provide protection for their semiconductor converters and semiconductor devices that is appropriate to the semiconductor techn

40、ology that they utilize. To consolidate alarm annunciation requirements upon operation of the protection scheme. To remove the requirement for the provision of an individual semiconductor fuse for each semiconductor device. 4-8-3/8.7 Inspection and Testing To align the requirements with the latest I

41、EC requirements. 4-8-3/9.1 Standard of Compliance To align the requirements with the latest IEC requirements. 4-8-3/9.5 Flame Retardant Standard To align the requirements with the latest IEC requirements. 4-8-3/9.7 Fire Resistant Standard To align the requirements with the latest IEC requirements. 4

42、 ABSRULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT .2016 Notices and General Information Part/Para. No. Title/Subject Status/Remarks 4-8-3/13.1 General To align the requirements with the latest IEC requirements. 4-8-3/13.3 Acceptable Types of Certified Safe Equipment To align the requirement

43、s with the latest IEC requirements. 4-8-3/Table 1B Degree of Protection of Electrical Equipment (Second IP Numeral) To include degree of protection “IP X9”, in line with the latest IEC requirements. 4-8-4/25.5.1 General To align the requirements with the latest IEC requirements. 4-8-4/25.5.2 Paint S

44、tores To align the requirements with the latest IEC requirements. 4-8-4/25.5.3 Battery Room To align the requirements with the latest IEC requirements. 4-8-4/25.5.4 Helicopter Refueling Facilities To align the requirements with the latest IEC requirements. 4-8-4A1/7.1 Flame Retardant Test To align t

45、he requirements with the latest IEC requirements. 4-8-5/3.7.4(a) Mechanical Construction and Configuration To align the requirements with the latest IEC requirements. 4-8-5/5.3.1 General To remove the option for a single electrical propulsion motor with two sets of windings. 4-8-5/5.7.5 (Deleted) Se

46、miconductor Converters To remove redundant requirements. 4-9-9/Table 8 Type Tests for Control, Monitoring and Safety Equipment To align the requirements with IACS UR E10. 4-9-9/Table 9 Tests for Unit Certification of Control, Monitoring and Safety Equipment To align the requirements with IACS UR E10

47、. ABSRULES FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT .2016 5 Part 1: Rules for Conditions of Classification High-Speed Craft RULES FOR CONDITIONS OF CLASSIFICATION HIGH-SPEED CRAFT 2016 PART 1 American Bureau of Shipping Incorporated by Act of Legislature of the State of New York 1862 Copyrig

48、ht 2015 American Bureau of Shipping ABS Plaza 16855 Northchase Drive Houston, TX 77060 USA Rule Change Notice (2016 ) Rule Change Notice (2016) The effective date of each technical change since 1993 is shown in parentheses at the end of the subsection/paragraph titles within the text of each Part. U

49、nless a particular date and month are shown, the years in parentheses refer to the following effective dates: (2000) and after 1 January 2000 (and subsequent years) (1996) 9 May 1996 (1999) 12 May 1999 (1995) 15 May 1995 (1998) 13 May 1998 (1994) 9 May 1994 (1997) 19 May 1997 (1993) 11 May 1993 Listing by Effective Dates of Changes from the 2015 Rules EFFECTIVE DATE 1 January 2016 shown as (2016) Part/Para. No. Title/Subject Status/Remarks 1-1-1/7 Scope of Classification To prohibit exceeding the design significant wave height for craft without the OE notation. 1-1-