BS PD ISO TS 13399-72-2016 Cutting tool data representation and exchange Creation of documents for the standardized data exchange Definition of properties for drawing header and th.pdf
《BS PD ISO TS 13399-72-2016 Cutting tool data representation and exchange Creation of documents for the standardized data exchange Definition of properties for drawing header and th.pdf》由会员分享,可在线阅读,更多相关《BS PD ISO TS 13399-72-2016 Cutting tool data representation and exchange Creation of documents for the standardized data exchange Definition of properties for drawing header and th.pdf(32页珍藏版)》请在麦多课文档分享上搜索。
1、PD ISO/TS 13399-72:2016 Cutting tool data representation and exchange Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML-data exchange BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06PD ISO/TS
2、13399-72:2016 PUBLISHED DOCUMENT National foreword This Published Document is the UK implementation of ISO/TS 13399-72:2016. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on th
3、is committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2016. Published by BSI Standards Limited 2016 ISBN 978 0 580 91036 4
4、 ICS 25.100.01; 35.240.50 Compliance with a British Standard cannot confer immunity from legal obligations. This Published Document was published under the authority of the Standards Policy and Strategy Committee on 31 July 2016. Amendments issued since publication Date Text affectedPD ISO/TS 13399-
5、72:2016 ISO 2016 Cutting tool data representation and exchange Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing header and their XML-data exchange Reprsentation et change des donnes relatives aux outils coupants Partie 72: Cration de la documenta
6、tion pour lchange de donnes normalises Dfinition des proprits des cartouches de plans et leur change de donnes en XML TECHNICAL SPECIFICATION ISO/TS 13399-72 Reference number ISO/TS 13399-72:2016(E) First edition 2016-07-15PD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E)ii ISO 2016 All rights reserved
7、 COPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intran
8、et, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org
9、 www.iso.orgPD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E)Foreword iv Introduction vi 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 2 3.1 Main data . 2 3.2 Drawing data . 3 3.3 Revision data 4 3.4 Item data 4 3.5 Customer data 4 3.6 Process data . 5 3.7 Bill of material (BOM) data 5
10、 4 Additional remark to the item in the bill of material . 7 4.1 General . 7 4.2 Data fields of the XML structure 7 4.3 Special data field 9 5 XML file . 9 5.1 General . 9 5.2 XML tags . 9 5.3 Root element 10 5.4 Data element 10 5.5 XML schema determinations .10 5.5.1 XML tag .10 5.5.2 XML tag .10 5
11、.5.3 XML tag .10 5.5.4 XML tag 11 5.5.5 XML tag 11 5.5.6 XML tag 11 5.5.7 XML tag .12 5.5.8 XML tag .12 5.5.9 XML tag 12 5.5.10 XML tag .13 5.5.11 XML tag .13 5.6 Structure of the XML file 13 Annex A (informative) Example of an XML file of a turning tool 15 Annex B (informative) Structure of the XML
12、 schema .17 Bibliography .21 ISO 2016 All rights reserved iii Contents PagePD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International
13、Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, al
14、so take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1.
15、 In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elem
16、ents of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations receive
17、d (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformit y assessment, as well as information about ISOs adh
18、erence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html. The committee responsible for this document is ISO/TC 29, Small tools. ISO/TS 13399 consists of the following parts, under the general title Cutting
19、tool data representation and exchange: Part 1: Overview, fundamental principles and general information model Part 2: Reference dictionary for the cutting items Technical Specification Part 3: Reference dictionary for tool items Technical Specification Part 4: Reference dictionary for adaptive items
20、 Technical Specification Part 5: Reference dictionary for assembly items Technical Specification Part 50: Reference dictionary for reference systems and common concepts Technical Specification Part 60: Reference dictionary for connection systems Technical Specification Part 70: Graphical data layout
21、 Layer settings for tool layout Technical Specification Part 71: Graphical data layout Creation of documents for the standardized data exchange Graphical product information Technical Specification Part 72: Creation of documents for the standardized data exchange Definition of properties for drawing
22、 header and their XML-data exchange Technical Specification Part 150: Usage guidelines Technical Specification Part 201: Creation and exchange of 3D models Regular inserts Technical Specification Part 202: Creation and exchange of 3D models Irregular inserts Technical Specification Part 203: Creatio
23、n and exchange of 3D models Replaceable inserts for drilling Technical Specificationiv ISO 2016 All rights reservedPD ISO/TS 13399-72:2016ISO/TS 13399-72:2016(E) Part 204: Creation and exchange of 3D models Inserts for reaming Technical Specification Part 301: Concept for the design of 3D models bas
24、ed on properties according to ISO/TS 13399-3: Modelling of thread-cutting taps, thread-forming taps and thread-cutting dies Technical Specification Part 302: Concept for the design of 3D models based on properties according to ISO/TS 13399-3: Modelling of solid drills and countersinking tools Techni
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSPDISOTS13399722016CUTTINGTOOLDATAREPRESENTATIONANDEXCHANGECREATIONOFDOCUMENTSFORTHESTANDARDIZEDDATAEXCHANGEDEFINITIONOFPROPERTIESFORDRAWINGHEADERANDTHPDF

链接地址:http://www.mydoc123.com/p-399315.html