BS ISO IEC 17629-2014 Information technology Office equipment Method for measuring first print out time for digital printing devices《信息技术 办公设备 数字印刷设备首次打印时间的测量方法》.pdf

《BS ISO IEC 17629-2014 Information technology Office equipment Method for measuring first print out time for digital printing devices《信息技术 办公设备 数字印刷设备首次打印时间的测量方法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO IEC 17629-2014 Information technology Office equipment Method for measuring first print out time for digital printing devices《信息技术 办公设备 数字印刷设备首次打印时间的测量方法》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO/IEC 17629:2014 Information technology Office equipment Method for measuring first print out time for digital printing devicesBS ISO/IEC 17629:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 17629:2014. The UK particip

2、ation in its preparation was entrusted to Technical Committee IST/3, IT Printers and Cartridges. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are respo

3、nsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 79054 6 ICS 37.100.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the St

4、andards Policy and Strategy Committee on 30 June 2014. Amendments issued since publication Date Text affectedBS ISO/IEC 17629:2014 Information technology Office equipment Method for measuring first print out time for digital printing devices Technologies de linformation quipements de bureau Mthode d

5、e mesure de la premire page hors dlai dun dispositif dimpression numrique ISO/IEC 2014 INTERNATIONAL STANDARD ISO/IEC 17629 First edition 2014-06-15 Reference number ISO/IEC 17629:2014(E)BS ISO/IEC 17629:2014ISO/IEC 17629:2014(E)ii ISO/IEC 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IE

6、C 2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be re

7、quested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO/IEC 17629:2014ISO/IEC 17629:201

8、4(E) ISO/IEC 2014 All rights reserved iii Contents Page Foreword iv Introduction v 1 Scope . 1 2 Terms and definitions . 1 3 Test Parameters and Conditions 3 3.1 Test Platform . 3 3.2 Test Platform Test Setup Procedures . 3 3.3 Printing Device System Setup 4 3.4 Printing Device Connection . 5 3.5 Pr

9、inting Device Condition . 5 3.6 Sample Size 5 3.7 Paper 5 3.8 Maintenance 5 3.9 Test Files, Test Suites and Software Applications . 5 3.10 Environment . 6 3.11 Voltage 6 4 Test Method 6 4.1 Test Measurement Procedure 6 4.2 Test Method Process .11 4.3 Required Tests 11 4.4 Optional Special Tests 12 5

10、 Calculations and Treatment of Data 13 5.1 Treatment of Data 13 5.2 FPOT from Ready .13 5.3 FPOT from Sleep .13 5.4 FPOT from Off .13 6 Presentation of Results .13 Annex A (normative) Test platform system parameters that may affect digital printing productivity measurements 16 Annex B (normative) Te

11、st Suite 20 Annex C (informative) Report Presentation 22 Annex D (informative) An example of printing device and test settings to record .24 Annex E (informative) An example of a Full Detailed Report 25 Annex F (normative) Procedure to Establish FPOT from Ready Delay Time .28BS ISO/IEC 17629:2014ISO

12、/IEC 17629:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a su

13、bject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (

14、IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should b

15、e noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identi

16、fying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenie

17、nce of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword -

18、Supplementary information The committee responsible for this document is ISO/IEC JTC 1, Information technology, Subcommittee SC 28, Office equipment.iv ISO/IEC 2014 All rights reservedBS ISO/IEC 17629:2014ISO/IEC 17629:2014(E) Introduction Many digital printing devices produce the first printed page

19、 at a different rate from subsequent pages. Due to this behaviour, nominal print speeds specified in pages per minute do not generally reflect the time to produce the first page. The degree to which a change in productivity is experienced depends significantly on many parameters of the job stream. T

20、he most dominant of the parameters of the job stream are: image quality modes selected, job content, B&W and colour reproduction, host computer, and connection type. This International Standard provides a general method for measuring first print out time when the above mentioned job stream parameter

21、s for digital printing devices are taken into consideration. It allows manufacturers and buyers of digital printing devices to describe the first print out time of various digital printing devices with respect to representative office usage. ISO/IEC 2014 All rights reserved vBS ISO/IEC 17629:2014BS

22、ISO/IEC 17629:2014Information technology Office equipment Method for measuring first print out time for digital printing devices 1 Scope This International Standard specifies a method for measuring first print out time of digital printing devices. The International Standard is applicable to digital

23、printing devices and multifunctional devices. The International Standard is intended to be used for black and white (B&W) as well as colour digital printing devices and multifunctional devices of any underlying marking technology. The International Standard includes instructions for test charts, tes

24、t setup procedure, test procedure, and the reporting requirements for the digital printing measurements. 2 Terms and definitions For the purposes of this document, the following terms and definitions apply. 2.1 duplex printing term used to describe uses in which a printing device prints on both side

25、s of a sheet Note 1 to entry: Another equivalent term is “two sided printing”. 2.2 first print out time FPOT number of seconds between the initiation of the job until the complete exit of the first sheet Note 1 to entry: Other equivalent terms are “first page out time”, “first print out”, “time to f

26、irst print”, and “time to first page”. Other similar terms have been used in industry as well. 2.3 full detailed report presentation of information including host computer setup and measured test results 2.4 full report presentation of measured test results 2.5 off state state from which a device is

27、 not capable of receiving and printing a print job without user intervention on the device Note 1 to entry: A device may enter Off state due to a user turning the device off, or device may enter Off state automatically after a delay. 2.6 paper feed orientation whether the long or short edge of the p

28、aper is leading in the paper transport mechanism Note 1 to entry: Typical devices with a maximum paper size of A4 have a paper feed orientation of short edge. Devices with a maximum paper size of A3 could print with A4 paper loaded in either long edge or short edge orientation. Typical devices with

29、a maximum paper size of 8,5” 11” have a paper feed orientation of short edge. Devices with a maximum paper size of 11” 17” could print with 8,5” 11” paper loaded in either long edge or short edge orientation. INTERNATIONAL ST ANDARD ISO/IEC 17629:2014(E) ISO/IEC 2014 All rights reserved 1BS ISO/IEC

30、17629:2014ISO/IEC 17629:2014(E) 2.7 power management delay time time that a device waits between the last print job and going into a lower power state such as sleep state or off state Note 1 to entry: The power management delay time corresponding to the setting as shipped is referred to as “default

31、power management delay time” or “default delay time”. 2.8 ready state state which a device typically enters after completing a print job where the printing engine is in a stable condition, but fully warmed up and prepared to print Note 1 to entry: While in ready state, systems not directly involved

32、with marking the media may be still in motion. For example, fans may still be spinning. 2.9 recovery time time required by a device to recover from sleep state given by the difference in FPOT between sleep state and ready state Note 1 to entry: Other related terms are “resume time” and “return time”

33、. Other similar terms have been used in industry as well. 2.10 simplex printing term used to describe uses in which a printing device prints on only one side of a sheet Note 1 to entry: Another equivalent term is “one sided printing”. 2.11 sleep state low power state from which a device is capable o

34、f receiving and printing a print job without user intervention on the device Note 1 to entry: Some devices may have multiple low power states. This International Standard focuses only on the lowest power sleep state. Note 2 to entry: Other equivalent terms are “power save”, “low power mode”, and “en

35、ergy save”. Other similar terms have been used in industry as well. 2.12 summary report presentation of results including only average FPOT from ready results 2.13 test file refers to the digital test file used for testing 2.14 test page first page or first two pages from a test file Note 1 to entry

36、: Duplex testing requires using the first two pages from a test file to print on both sides of the first sheet. Simplex testing only requires using the first page from a test file to print on one side of the first sheet. 2.15 test platform set of hardware and software system components configured to

37、 perform the collection of digital printing FPOT tests, including, but not limited to a computer installed with an operating system and applicable application software, installed printing device software, hardware and software interfaces, and timing devices (stopwatch or automated)2 ISO/IEC 2014 All

38、 rights reservedBS ISO/IEC 17629:2014ISO/IEC 17629:2014(E) 2.16 test run refers to the operation of printing a test page or multiple test pages, in a particular system configuration Note 1 to entry: Print times are recorded for each test run. 2.17 test suite refers to the combination of test files u

39、sed to measure FPOT 2.18 warm-up time time required by a device to recover from off state given by the difference in FPOT between off state and ready state Note 1 to entry: Other similar terms, such as “wait time”, have been used in industry as well. 3 Test Parameters and Conditions 3.1 Test Platfor

40、m Due to the rapid change of computer technology, a common test platform (hardware and software) that can be used for FPOT testing over time is considered to be not practical. Instead, when a test platform is used, the test platform system parameters that may affect digital printing productivity mea

41、surements (see Annex A) shall be recorded. 3.2 Test Platform Test Setup Procedures 3.2.1 Initial Platform Setup The test platform hardware should be installed as per the manufacturers instructions. The test platform hardware information shall be recorded as listed in Annex A. The test platform opera

42、ting system and applications should be installed as per the manufacturers instructions. The test platform operating system and application information shall be recorded as per Annex A. All settings or selections made during installation that differ from the applications default settings or operating

43、 systems default settings shall be recorded. The test platform should be configured for the appropriate connection environment, such as direct USB connection or network Ethernet connection, and the information shall be recorded as per Annex A along with all settings and selections that differ from t

44、he installation default configuration. It should be verified that the test platform is configured for optimal performance by evaluating system parameters such as hard disk fragmentation and compression, swap memory size, etc. Any settings, changes or optimizations made that differ from the installat

45、ion default condition shall be recorded. The test platform is now in the Initial Installation State. All recorded settings shall be included in the Full Detailed Test report. 3.2.2 Creation of Disk Image of Test Platform (optional) Disk imaging software may be used to enable the system to be restore

46、d to the Initial Installation State. Create the disk image after the test platform has been configured and before the print driver for the printing device is installed. Record the disk imaging software used and all settings that differ from the imaging softwares installation default condition. ISO/I

47、EC 2014 All rights reserved 3BS ISO/IEC 17629:2014ISO/IEC 17629:2014(E) 3.2.3 Initial Test State The test platform shall be restored to the Initial Installation State before beginning the sequence of tests for each new printing device. Each printing device product bundle or printing device hardware

48、configuration that might be expected to result in a difference in performance should be considered a different printing device. Record the method used to establish the Initial Installation State. 3.3 Printing Device System Setup Place the printing device on a horizontal surface and setup the printin

49、g device according to the manufacturers recommendation. Install the software (driver, port, etc.) recommended by the manufacturer. Use the most recent print driver available from the manufacturer. The driver and driver version shall be recorded on the test report. The standard test shall be conducted using the manufacturers default driver for the given printing device. If a default driver is not installed/selected automatically by the manufacturers installation procedure, consult the manufacturers documentation