BS ISO 9838-2015 Alpine and touring ski-bindings Test soles for ski-binding tests《登山和旅游滑雪橇固定装置 雪橇固定装置试验用试验鞋底》.pdf
《BS ISO 9838-2015 Alpine and touring ski-bindings Test soles for ski-binding tests《登山和旅游滑雪橇固定装置 雪橇固定装置试验用试验鞋底》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 9838-2015 Alpine and touring ski-bindings Test soles for ski-binding tests《登山和旅游滑雪橇固定装置 雪橇固定装置试验用试验鞋底》.pdf(18页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards Publication BS ISO 9838:2015 Alpine and touring ski-bindings Test soles for ski-binding testsBS ISO 9838:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 9838:2015. It supersedes BS ISO 9838:2008 which is withdrawn. The UK participation in i
2、ts preparation was entrusted to Technical Committee SW/136, Sports, playground and other recreational equipment. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract.
3、 Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 88534 1 ICS 97.220.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the aut
4、hority of the Standards Policy and Strategy Committee on 30 September 2015. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO 9838:2015 ISO 2015 Alpine and touring ski-bindings Test soles for ski-binding tests Fixations de skis alpins et de randonne Semelles dessai po
5、ur les essais de fixations de skis INTERNATIONAL STANDARD ISO 9838 Third edition 2015-09-01 Reference number ISO 9838:2015(E)BS ISO 9838:2015ISO 9838:2015(E)ii ISO 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in Switzerland All rights reserved. Unless otherwise specified
6、, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs m
7、ember body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgBS ISO 9838:2015ISO 9838:2015(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 T erms and defini
8、tions . 1 4 Material and manufacture 2 5 Dimensions . 2 6 Mechanical properties 5 6.1 Flexional stiffness . 5 6.2 Compressional stiffness 6 6.3 Hardness . 7 6.3.1 Form A types A and C . 7 6.3.2 Form T . 7 6.4 Coefficient of friction . 7 6.4.1 Form A types A and C . 7 6.4.2 Form T . 7 6.5 Coefficient
9、 of thermal expansion 8 6.6 Requirements . 8 7 Long-term use 8 Bibliography 9 ISO 2015 All rights reserved iii Contents PageBS ISO 9838:2015ISO 9838:2015(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). T
10、he work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-go
11、vernmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described
12、 in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to th
13、e possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO
14、list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as
15、well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 83, Sports and other recreational facilities and equipment, Subcommittee SC 4, Sno
16、wsports equipment. This third edition cancels and replaces the second edition (ISO 9838:2008), of which it constitutes a minor revision.iv ISO 2015 All rights reservedBS ISO 9838:2015INTERNATIONAL ST ANDARD ISO 9838:2015(E) Alpine and touring ski-bindings Test soles for ski- binding tests 1 Scope Th
17、is International Standard defines test soles representing an alpine ski-boot (form A) or at least the bottom part of it to be used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465, and a touring ski-boot (form T) or at least the bottom part of it to be used
18、for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465. NOTE Ski-boots have their own International Standards (ISO 5355 and ISO 9523) that allow relatively large tolerances in defining the test sole which are generally believed to be suitable for on-slope use b
19、y skiers, but too large for reproducible laboratory measurements. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references,
20、the latest edition of the referenced document (including any amendments) applies. ISO 868, Plastics and ebonite Determination of indentation hardness by means of a durometer (Shore hardness) ISO 5355, Alpine ski-boots Requirements and test methods ISO 9462, Alpine ski-bindings Requirements and test
21、methods 3 T erms a nd definiti ons For the purposes of this document, the terms and definitions given in ISO 5355 and the following apply. 3.1 test sole form A test sole for testing alpine ski-bindings 3.2 test sole form T test sole for testing touring ski-bindings 3.3 test sole type A test sole for
22、 adults in accordance with ISO 5355, type A, suitable for bindings of type A (adults) and CA (junior) in accordance with ISO 9462 3.4 test sole type C test sole for children in accordance with ISO 5355, type C, suitable for bindings of type C (children) in accordance with ISO 9462 3.5 basic test sol
23、e one-piece sole of length 305 mm for type A and 255 mm for type C ISO 2015 All rights reserved 1BS ISO 9838:2015ISO 9838:2015(E) 3.6 variable length soles sole that is either adjustable, in two parts, or a set of several fixed length soles between 270 mm and 360 mm for type A and between 200 mm and
24、 280 mm for type C 4 Material and manufacture The sole shall be moulded in polyurethane (TPU) reinforced by a metal insert in order to achieve the mechanical requirements given in Clause 6. It is moulded in a homogeneous material and in a mould with the same roughness on the sole/binding interface t
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO98382015ALPINEANDTOURINGSKIBINDINGSTESTSOLESFORSKIBINDINGTESTS 登山 旅游 滑雪 固定 装置 雪橇 试验 鞋底 PDF

链接地址:http://www.mydoc123.com/p-396136.html