BS ISO 776-2011 en_6416 Pulps Determination of acid-insoluble ash《纸浆.酸不溶灰分的测定》.pdf

《BS ISO 776-2011 en_6416 Pulps Determination of acid-insoluble ash《纸浆.酸不溶灰分的测定》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 776-2011 en_6416 Pulps Determination of acid-insoluble ash《纸浆.酸不溶灰分的测定》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwide NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BSI Standards Publication BS ISO 776:2011 Pulps Determination of acid-insoluble ashBS ISO 776:2011 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 776:2011. It

2、supersedes BS 4496:1984, which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PAI/11, Methods of test for paper, board and pulps. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not p

3、urport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 68302 2 ICS 85.040 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the

4、 Standards Policy and Strategy Committee on 30 November 2011. Amendments issued since publication Date T e x t a f f e c t e dBS ISO 776:2011 Pulps Determination of acid- insoluble ash Ptes Dtermination des cendres insolubles dans lacide ISO 2011 Reference number ISO 776:2011(E) Third edition 2011-0

5、8-15 ISO 776 INTERNATIONAL STANDARDBS ISO 776:2011 ISO 776:2011(E)COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfi

6、lm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011

7、 All rights reservedBS ISO 776:2011 Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body i

8、nterested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechn

9、ical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by th

10、e technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights

11、. ISO shall not be held responsible for identifying any or all such patent rights. ISO 776 was prepared by Technical Committee ISO/TC 6, Paper, board and pulps. This third edition cancels and replaces the second edition (ISO 776:1982), which has been technically revised. The ignition temperature has

12、 been changed from 575 C to 525 C to be consistent with the temperature specified in ISO 1762. The method also requires that the minimum mass of acid-insoluble residue be 10 mg instead of 1 mg, in order to improve the accuracy of the test. ISO 776:2011(E) ISO 2011 All rights reserved iiiBS ISO 776:2

13、011 Introduction Acid-insoluble ash consists primarily of silica and silicates. This material, when present in the finished paper or paperboard, can have an abrasive effect on punches, knives, slitters and dies which come into contact with paper during finishing operations. Paper made from pulps wit

14、h more than 400 mg/kg (based on oven-dried mass) of acid-insoluble ash can cause premature dulling of such equipment. The level of silica in pulp can vary significantly depending on several factors, including wood type, water quality, and the presence of silicate- based additives, such as clay and t

15、alc. For example, in bleached kraft pulps, the silica mass fraction can range from under 100 mg/kg to over 1 000 mg/kg. ISO 776:2011(E)iv ISO 2011 All rights reservedBS ISO 776:2011 INTERNATIONAL STANDARD ISO 776:2011(E) Pulps Determination of acid-insoluble ash 1 Scope This International Standard s

16、pecifies a method for the determination of the acid-insoluble ash of pulp. It is applicable to all types of pulps. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refer

17、ences, the latest edition of the referenced document (including any amendments) applies. ISO 638, Paper, board and pulps Determination of dry matter content Oven-drying method ISO 1762, Paper, board and pulps Determination of residue (ash) on ignition at 525 C ISO 7213, Pulps Sampling for testing 3

18、Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 acid-insoluble ash insoluble residue remaining after a pulp sample is ignited in a furnace at 525 C 25 C and the ash treated with hydrochloric acid as specified in this International Standard 4 Pr

19、inciple A test specimen is weighed in a heat-resistant container, ignited in a muffle furnace at 525 C 25 C, and the residue is treated with hydrochloric acid. The insoluble residue after acid treatment is filtered, washed, ignited at 525 C and weighed. The moisture content of a separate test portio

20、n is also measured. The acid-insoluble ash is then determined, in milligrams per kilogram, on an oven-dry basis, from the mass of the insoluble residue after ignition and the dry matter content of the sample. 5 Reagent Use only analytical grade reagent and distilled water or water of equivalent puri

21、ty. 5.1 Hydrochloric acid, 6 mol/l solution. Carefully, in a fume hood, dilute 500 ml of hydrochloric acid (density at 20 C = 1,19 kg/l) to 1 000 ml with water. 6 Apparatus 6.1 Heat-resistant evaporating dishes, of capacity 50 ml to 100 ml, and crucibles with a capacity of 20 ml. Platinum containers

22、 are preferred, but porcelain or silica may be used. 6.2 Steam bath or electric hotplate, capable of maintaining a surface temperature of 110 C to 130 C. ISO 2011 All rights reserved 1BS ISO 776:2011 6.3 Analytical balance, of capacity 100 g, accurate to 0,1 mg. 6.4 Desiccator. 6.5 Muffle furnace, c

23、apable of maintaining a temperature of 525 C 25 C. 6.6 Filter paper, quantitative, ashless, double acid-washed, of a type recommended for fine precipitates (e.g. Whatman No. 42 1)or equivalent). 6.7 Drying oven, capable of maintaining an air temperature of 105 C 2 C and suitably ventilated. 7 Sampli

24、ng and preparation of test specimen If the analysis is done in order to evaluate a pulp lot, obtain a representative pulp sample as described in ISO 7213. If it is not, report the source of the sample and, if possible, the sampling procedure used. Sufficient sample shall be collected to allow for at

25、 least duplicate determinations and for the determination of moisture content. Obtain a test specimen consisting of small pieces, not larger than 1 cm 2 , from various parts of the sample in such a manner as to be thoroughly representative of it. The mass of the test portion shall be such that the m

26、ass of the acid-insoluble residue is greater than 10 mg. A test portion weighing 25 g is sufficient in most cases. NOTE In samples with very low levels of acid-insoluble residue, it might be necessary to obtain a larger test specimen and to ignite it in more than one portion. 8 Procedure Carry out t

27、he procedure in duplicate. Condition the test specimens and moisture specimens in the laboratory atmosphere until they reach equilibrium moisture. Determine the moisture content of the sample as described in ISO 638. Weigh this test portion at the same time as the test portion used for ash determina

28、tion. Ash the test specimens as described in ISO 1762, in a dish previously ignited in the muffle furnace, to a constant mass (to the nearest 0,1 mg). If the dish is too small to hold the entire specimen, the specimen shall be ashed in portions. Place a portion of the specimen in the dish and burn i

29、t gently to avoid any loss. Then add the next portion to the dish and burn it gently. Continue this process until the entire specimen has been carbonized, as indicated by the absence of black carbon particles. Cool the dish to room temperature in a fume hood, add 5 ml of 6 mol/l HCl (5.1), and evapo

30、rate carefully to dryness on a steam bath or hotplate (6.2). Repeat the treatment. Add a third 5 ml aliquot of 6 mol/l HCl (5.1) to the residue, heat for 2 min on the steam bath or hotplate, and dilute with 20 ml of water. Quantitatively transfer the residue by filtering through the filter paper (6.

31、6), being careful to remove all the residue from the dish with water. Wash the residue several times with hot water until the filtrate is free of chloride ions. The absence of chloride ions in the filtrate may be confirmed with a few drops of 5 % silver nitrate. The filtrate should not produce a whi

32、te precipitate or opalescence. Carefully place the filter paper and residue into a tared 20 ml crucible or heat-resistant evaporating dish (6.1). Heat gently until dry, then ignite at 525 C 25 C until the entire specimen has been ashed, as indicated by the absence of black carbon particles. Cool the

33、 crucible in a desiccator and weigh to the nearest 0,1 mg. Repeat the ignition until a constant mass is obtained. 1) Whatman No. 42 is an example of a suitable product available commercially. This information is given for the convenience of users of this document and does not constitute an endorseme

34、nt by ISO of this product. ISO 776:2011(E)2 ISO 2011 All rights reservedBS ISO 776:2011 9 Calculation Calculate the mass fraction of acid-insoluble ash according to Equation (1): a (1) where w ais the mass fraction of acid-insoluble ash, expressed as milligrams per kilogram of the oven-dry sample; m

35、 1is the mass of insoluble residue after ignition at 525 C 25 C, in milligrams; m 2is the mass of the sample, on an oven-dry basis, in grams. Report the mean of duplicate determinations to the nearest 5 mg/kg. 10 Test report The test report shall include the following information: a) a reference to

36、this International Standard (ISO 776:2011); b) the date and place of testing; c) a complete identification of the sample tested; d) the result, expressed as indicated in Clause 9; e) any departure from the procedure described in this International Standard or any other circumstances which may have a

37、ffected the result. ISO 776:2011(E) ISO 2011 All rights reserved 3BS ISO 776:2011 Annex A (informative) Precision A.1 General In August 2009, an international round robin was performed in which eight laboratories from five different countries participated. Three samples of different types of pulp we

38、re tested. Each sample was disintegrated, to ensure its homogeneity, and made into handsheets. Several handsheets from each sample were submitted to the participating laboratories for testing according to this International Standard. For the two hardwood bleached kraft pulp samples, the data from tw

39、o of the eight laboratories were considered as outliers and were not included in the precision statement. The calculations were made according to ISO/TR 24498, Paper, board and pulps Estimation of uncertainty for test methods. The repeatability and reproducibility limits reported are estimates of th

40、e maximum difference which should be expected in 19 of 20 instances, when comparing two test results for material similar to those described under similar test conditions. These estimates may not be valid for different materials or different test conditions. NOTE Repeatability and reproducibility li

41、mits are calculated by multiplying the repeatability and reproducibility standard deviations by 2,77, where 2,77 = 1,96 2 . A.2 Repeatability Table A.1 Estimation of the repeatability of the test method Sample Number of laboratories Mean value Standard deviation Coefficient of variation Repeatabilit

42、y limitmg/kg s r mg/kg C V, r % r mg/kg Hardwood bleached kraft pulp (low ash) 6 1 368 72,6 5,3 201 Hardwood bleached kraft pulp (high ash) 6 2 909 72,4 2,5 201 Clay-filled mechanical pulp furnish 8 112 955 4 611 4,1 12 781 ISO 776:2011(E)4 ISO 2011 All rights reservedBS ISO 776:2011 A.3 Reproducibi

43、lity Table A.2 Estimation of the reproducibility of the test method Sample Number of laboratories Mean value Standard deviation Coefficient of variation Reproducibility limitmg/kg s R mg/kg C V, R % R mg/kg Hardwood bleached kraft pulp (low ash) 6 1 368 112 8,2 311 Hardwood bleached kraft pulp (high

44、 ash) 6 2 909 165 5,7 458 ISO 776:2011(E) ISO 2011 All rights reserved 5BS ISO 776:2011 ISO 776:2011(E) ICS 85.040 Price based on 5 pages ISO 2011 All rights reservedThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-

45、related publications, information and services. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. British Standards Institution (BSI) raising standards worldwide BSI Group Headquarters 389 Chiswick High Road London W4 4AL UK Tel +44 (

46、0)20 8996 9001 Fax +44 (0)20 8996 7001 British Standards are updated by amendment or revision. Users of British Stan- dards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and serv- ices. We would be grateful

47、 if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical com- mittee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 BSI offers Members an individual updati

48、ng service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001 Email: Buying standards You may buy PDF and hard copy versions of standards directly using a credit card from the BSI Shop on the website

49、In addition all orders for BSI, international and foreign standards publications can be addressed to BSI Customer Services. Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001 Email: In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on sta