BS ISO 603-4-1999 en_9615 Bonded abrasive products - Dimensions - Grinding wheels for surface grinding peripheral grinding《粘合磨料产品.尺寸.平面磨削 外圆周磨削砂轮》.pdf

《BS ISO 603-4-1999 en_9615 Bonded abrasive products - Dimensions - Grinding wheels for surface grinding peripheral grinding《粘合磨料产品.尺寸.平面磨削 外圆周磨削砂轮》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 603-4-1999 en_9615 Bonded abrasive products - Dimensions - Grinding wheels for surface grinding peripheral grinding《粘合磨料产品.尺寸.平面磨削 外圆周磨削砂轮》.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS ISO 603-4:1999 ICS 25.

2、100.70 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Bonded abrasive products Dimensions Part 4: Grinding wheels for surface grinding/peripheral grindingThis British Standard, having been prepared under the direction of the Engineering Sector Committee, was published under t

3、he authority of the Standards Committee and comes into effect on 15 November 1999 BSI 11-1999 ISBN 0 580 35700 7 BS ISO 603-4:1999 Amendments issued since publication Amd. No. Date Comments National foreword This British Standard reproduces verbatim ISO 603-4:1999 and implements it as the UK nationa

4、l standard. The UK participation in its preparation was entrusted to Technical Committee MTE/13, Grinding wheels, abrasive tools, paper, cloths and powder, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries

5、 on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British

6、Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does

7、not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside

8、 front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 16, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.A Referencenumbe r ISO6034:1999 (E) INTERNATIONAL STANDARD ISO 6034 Firstedition 199

9、90715 Bondedabrasiveproducts Dimensions Part4: Grindingwheelsforsurfacegrinding/peripheral grinding ProduitsabrasifsagglomrsDimensions Partie4:Meulespourrectificationplane/meulagetangentielISO6034:1999(E) ii Contents Page 1Scop e1 2Normativereference s2 3Dimension s.3 3.1Type1:Straightgrindingwhee l

10、3 3.2Type5:Wheelrecessedononesid e4 3.3Type7:Wheelrecessedonbothside s.6 3.4Type20:Wheelrelievedononesid e8 3.5Type21:Wheelrelievedonbothside s.8 3.6Type22:Wheelrelievedononesideandrecessedontheothersid e9 3.7Type23:Wheelrelievedandrecessedononesid e9 3.8Type24:Wheelrelievedandrecessedononesideandre

11、cessedontheothersid e10 3.9Type25:Wheelrelievedandrecessedononesideandrelievedontheothersid e11 3.10Type26:Wheelrelievedandrecessedonbothside s.12 3.11Type38:Hubbedwhee l13 3.12Type39:Doublehubbedwhee l.13 4Designatio n15 5Specification s.15 5.1Tolerance s.15 5.2Balancin g.15 5.3Markin g15 Bibliogra

12、phy16 ISO6034:1999(E) iii Foreword ISO (the InternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcom

13、mitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnongovernmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalS

14、tandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtoth ememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. InternationalStandardISO6034

15、waspreparedbyTechnicalCommitteeISO/TC 29,Smalltools,subcommittee SC5, Grindingwheelsandabrasives . Thisfirstedition,togetherwithISO6031:1999toISO6033:1999andISO6035:1999toISO 60316:1999 , cancels andreplacesISO/R603:1967,ISO6032:1981,ISO1117:1975,ISO2220:1972,ISO2933:1974,ISO 3290:1976 andISO3921:19

16、76asatechnicalrevisionofthesestandards. ISO603consistsofthefollowingparts,underthegeneraltitle BondedabrasiveproductsDimensions : Part1:Grindingwheelsforexternalcylindricalgrindingbetweencentres Part2:Grindingwheelsforcentrelessexternalcylindricalgrinding Part3:Grindingwheelsforinternalcylindricalgr

17、inding Part4:Grindingwheelsforsurfacegrinding/peripheralgrinding Part5:Grindingwheelsforsurfacegrinding/facegrinding Part6:Grindingwheelsfortoolandtoolroomgrinding Part7:Grindingwheelsformanuallyguidedgrinding Part8:Grindingwheelsfordeburringandfettling/snagging Part9:Grindingwheelsforhighpressuregr

18、inding Part10:Stonesforhoningandsuperfinishings Part11:Handfinishingsticks Part12:Grindingwheelsfordeburringandfettlingonastraightgrinder Part13:Grindingwheelsfordeburringandfettlingonaverticalgrinder Part14:Grindingwheelsfordeburringandfettling/snaggingonananglegrinder Part15:Grindingwheelsforcutti

19、ngoffonstationaryormobilecuttingoffmachines Part16:GrindingwheelsforcuttingoffonhandheldpowertoolsINTERNATIONALSTANDARD ISO6034:1999(E) 1 BondedabrasiveproductsDimensions Part4: Grindingwheelsforsurfacegrinding/peripheralgrinding 1Scope ThispartofISO603specifiesthenominaldimensions,inmillimeters,of:

20、 Type1:Straightgrindingwheel Type5:Wheelrecessedononeside Type7:Wheelrecessedonbothsides Type20:Wheelrelievedononeside Type21:Wheelrelievedonbothsides Type22:Wheelrelievedononesideandrecessedontheotherside Type23:Wheelrelievedandrecessedononeside Type24:Wheelrelievedandrecessedononesideandrecessedon

21、theotherside Type25:Wheelrelievedandrecessedononesideandrelievedontheotherside Type26:Wheelrelievedandrecessedonbothsides. Type38:Hubbedwheel Type39:Doublehubbedwheel Thesebondedabrasiveproductsareintendedtobeusedforthegrindingofplanesurfaceswher etheworkpieceis securedtoareciprocatingtable.Theworkp

22、ieceandthegrindingwheelaremechanicallyguided.ISO6034:1999(E) 2 2Normativereferences The following normativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsof this partofISO 603.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdo notapply.Ho

23、wever,partiestoagreementsbasedonthispartofISO 603areencouragedtoinvestigatethe possibilityofapplyingthemostrecenteditionsofthenormativedocumentsindicatedbelow.For undated references,thelateseditionofthenormativedocumentreferre dtoapplies.MembersofISOandIECmaintain registersofcurrentlyvalidInternatio

24、nalStandards. ISO525:1999, BondedabrasiveproductsGeneralrequirements . ISO6103:1999, BondedabrasiveproductsStaticbalancingofgrindingwheelsTesting . ISO13942: 1) , BondedabrasiveproductsLimitdeviationsandrunouttolerances. 1) Tobepublished. ISO6034:1999(E) 3 3Dimensions 3.1Type1:Straightgrindingwheel

25、SeeFigure1andTable1. Figure1Type1 Table1DimensionsofType1 DT H 13 20 25 32 50 80 100 160 150 180 200 250 300 X X X X X X X X X X X X X X X X X X X X X X 32 50,8 76,2 127 350/356 400/406 X X X X X X X X X X 76,2 127 500/508 600/610 750/762 X X X X X X X X X X X X X X X X 203,2 304,8ISO6034:1999(E) 4

26、3.2Type5:Wheelrecessedononeside SeeFigure2andTable2. Figure2Type5 ISO6034:1999(E) 5 Table2DimensionsofType5 DTHPFR max 150 180 200 200 250 250 300 300 350/356 400/406 450/457 450/457 25 32 25 32 25 32 25 32 32 40 32 40 40 50 40 50 40 50 40 50 63 80 40 50 63 80 32 32 50,8 50,8 76,2 76,2 127 127 127 1

27、27 203,2 80 100 110 110 150 150 150 190 215 215 215 280 10 13 10 13 10 13 10 13 13 13 13 13 25 13 25 1 32 5 500/508 500/508 600/610 600/610 750/762 900/914 40 50 63 80 40 50 63 80 63 80 100 63 80 100 63 80 100 63 80 100 203,2 304,8 203,2 304,8 304,8 304,8 400 400 400 400 400 450 13 25 13 25 13 25 50

28、 13 25 50 13 25 50 13 25 50 8ISO6034:1999(E) 6 3.3Type7:Wheelrecessedonbothsides SeeFigure3andTable3. Figure3Type7 ISO6034:1999(E) 7 Table3DimensionsofType7 DTHPFGR max 300 40 50 76,2 150 6 10 6 10 3,2 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 63 80 50 63 80 127 127 127 127 203,2 190 215

29、 215 215 280 6 10 10 10 13 10 13 6 10 10 10 13 10 13 5 500/508 500/508 600/610 600/610 750/762 900/914 40 50 63 80 40 50 63 80 50 63 80 100 50 63 80 100 80 100 80 100 203,2 304,8 203,2 304,8 304,8 304,8 400 400 400 400 400 450 10 13 10 13 10 13 10 13 13 13 10 13 10 13 10 13 25 10 13 25 13 25 13 25 8

30、ISO6034:1999(E) 8 3.4Type20:Wheelrelievedononeside SeeFigure4andTable4. Figure4Type20 3.5Type21:Wheelrelievedonbothsides SeeFigure5andTable4. Figure5Type21 Table4DimensionsofType20andType21 DTHKN a a R max 13 16 20 25 32 40 50 63 80 100 125 2 4 250XXXXXX 76,2 127 150 190 2 1 4 2 3,2 5 300 300/356 40

31、0/406 450/457 X X X X X X X X X X X X X X X X X X X X X X X X X X X 76,2 127 127 127 203,2 150 190 215 215 280 3 2 2 3 4 3 5 4 5 7 8 6 3,2 5 500/508 600/610 750/762 X X X X X X X X X X X X X X X X X X X X 203,2 304,8 203,2 304,8 304,8 400 400 2 4 6 4 7 13 8 a Thevalues N or2 Naretakenlessthanorequal

32、tohalfthickness T. ISO6034:1999(E) 9 3.6Type 22: Wheel relievedononesideand recessedontheotherside SeeFigure6andTable5. Figure6Type22 3.7Type23:Wheelrelievedandrecesse don oneside SeeFigure7andTable5. Figure7Type23 Table5DimensionsofType22andType23 DTHK=PF N a R max 2 4 300 300 350/356 400/406 450/4

33、57 450/457 40 50 40 50 40 50 40 50 63 80 40 50 63 80 76,2 127 127 203,2 150 190 215 280 13 13 13 25 13 25 3 3 2 2 2 2 3 3 4 4 3 3 3 3 5 5 4 4 5 5 7 7 8 8 6 6 6 6 3,2 5 500/508 500/508 600/610 600/610 750/762 040 50 63 80 40 50 63 80 63 80 100 63 80 100 63 80 100 203,2 304,8 203,2 304,8 304,8 400 400

34、 400 400 400 13 25 13 25 13 25 40 13 25 40 13 25 40 2 2 2 2 2 2 2 2 4 4 4 4 4 4 6 6 6 4 4 4 4 4 4 4 4 7 7 7 7 7 7 13 13 8ISO6034:1999(E) 10 3.8Type24:Wheelrelievedandrecessedononesideandrecessedontheotherside SeeFigure8andTable6. Figure8Type24 Table6DimensionsofType24 DTHPF a G a N a a R max 2 4 300

35、 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 40 50 63 80 50 63 80 76,2 127 127 127 203,2 150 190 215 215 280 6 10 6 10 6 10 13 6 13 6 10 6 10 6 13 6 13 2 3 2 3 2 2 3 3 4 4 3 3 3 4 4 5 5 7 7 8 8 6 6 6 3,2 5 500/508 500/508 600/610 600/610 750/762 40 50 63 80 40 50 63 80 50 63 80 100 50 63 8

36、0 100 80 100 203,2 304,8 203,2 304,8 304,8 400 400 400 6 13 6 13 6 13 6 13 13 6 13 6 13 6 13 25 6 13 25 13 25 2 2 2 2 2 2 2 2 4 4 4 4 4 4 4 4 6 6 4 4 4 4 4 4 4 4 7 7 7 7 7 7 13 8 a The valuesN + F + Garetakenlessthanorequaltohalfthickness T. ISO6034:1999(E) 11 3.9Type25:Wheelrelievedandrecessedonone

37、sideandrelievedontheotherside SeeFigure9andTable7. Figure9Type25 Table7DimensionsofType25 DTHK=PF a N a a R max 2 4 300 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 40 50 63 80 40 50 63 80 76,2 127 127 127 127 203,2 150 190 215 215 215 280 13 13 13 13 25 13 25 3 3 2 2 2 2 3 3 4 4 3 3 3 3 5

38、4 5 6 8 7 6 6 6 3,2 5 500/508 500/508 600/610 600/610 750/762 40 50 63 80 40 50 63 80 63 80 100 63 80 100 63 80 100 203,2 304,8 203,2 304,8 304,8 400 400 400 400 400 13 25 13 25 13 25 40 13 25 40 13 25 40 2 2 2 2 2 2 2 2 4 4 4 4 4 4 6 6 5 4 4 4 4 4 4 7 7 7 7 8 a Thevalues 2N + F aretakenlessthanoreq

39、ualtohalfthickness T.ISO6034:1999(E) 12 3.10Type26:Wheelrelievedandrecessedonbothsides SeeFigure10andTable8. Figure10Type26 Table8DimensionsofType26 DTHPF a G a N a a R max 2 4 300 300 350/356 400/406 450/457 450/457 40 50 40 50 40 50 40 50 63 80 50 63 80 76,2 127 127 127 127 203,2 150 190 215 215 2

40、15 280 6 10 6 10 6 6 6 13 6 13 6 10 6 10 6 6 6 13 6 13 2 2 2 2 2 2 3 3 4 4 3 3 3 4 4 5 6 8 7 6 6 6 3,2 5 500/508 500/508 600/610 600/610 750/762 40 50 63 80 40 50 63 80 50 63 80 100 50 63 80 100 80 100 203,2 304,8 203,2 304,8 304,8 400 400 400 400 400 6 13 6 13 6 13 6 13 13 6 13 6 13 6 13 25 6 13 25

41、 13 25 2 2 2 2 2 2 2 2 4 4 4 4 4 4 6 6 4 4 4 4 4 4 8 a Thevalues 2N + F + Garetakenlessthanorequaltohalfthickness T. ISO6034:1999(E) 13 3.11Type38:Hubbedwheel SeeFigure11andTable9. a Chamferorradiuslefttothemanufacturersdiscretion. Figure11Type38 3.12Type39:Doublehubbedwheel SeeFigure12andTable9. a

42、Chamferorradiuslefttothemanufacturersdiscretion. Figure12Type39ISO6034:1999(E) 14 Table9DimensionsofType38andType39 DJT U H 3 5 8 13 20 25 32 40 250 180 190 13XXX 76,2 127 250 180 190 20X 76,2 127 300 180 220 13XX 076,2 127 300 180 220 20X 076,2 127 350/356 245 20 25 X X X 127 400/406 245 20 25 32 X

43、 X X 127 450/457 245 20 25 32 X X X X 127 500/508 500/508 420 25 32 X X X 203,2 304,8 203,2 304,8 600/610 600/610 600/610 420 25 32 40 X X X X 203,2 304,8 203,2 304,8 203,2 304,8 750/762 420 32 40 50 X X X X X 304,8 900/914 550 32 40 50 X X X X X 304,8 1060/1067 550 32 40 50 X X X X X 304,8 ISO6034:1999(E) 15 4Designation A complete designation ofa bonded abrasive product in accordancewiththispartofISO 603shal