IEC 62148-2-2010 Fibre optic active components and devices - Package interface standards - Part 2 SFF 10-pin transceivers《光纤有源元件及器件.包装接口标准.第2部分 SFF 10针收发器》.pdf

《IEC 62148-2-2010 Fibre optic active components and devices - Package interface standards - Part 2 SFF 10-pin transceivers《光纤有源元件及器件.包装接口标准.第2部分 SFF 10针收发器》.pdf》由会员分享，可在线阅读，更多相关《IEC 62148-2-2010 Fibre optic active components and devices - Package interface standards - Part 2 SFF 10-pin transceivers《光纤有源元件及器件.包装接口标准.第2部分 SFF 10针收发器》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62148-2 Edition 2.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic active components and devices Package and interface standards Part 2: SFF 10-pin transceivers Composants et dispositifs actifs en fibres optiques Normes de botier et dinterface Partie 2: Emetteurs-rcepteurs SFF

2、10 broches IEC 62148-2:2010 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and mic

3、rofilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member N

4、ational Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccor

5、d crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. I

6、EC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related tec

7、hnologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalog

8、ue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a

9、 month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages

10、. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 9

11、19 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI L

12、e contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet de

13、ffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just P

14、ublished dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais,

15、ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, vi

16、sitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62148-2 Edition 2.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic active components and devices Package and interface standards Part 2: SFF 10-pin transceivers Compos

17、ants et dispositifs actifs en fibres optiques Normes de botier et dinterface Partie 2: Emetteurs-rcepteurs SFF 10 broches INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE P ICS 33.180.01 PRICE CODE CODE PRIX ISBN 978-2-88912-297-4 Registered trademark of the Inter

18、national Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 62148-2 IEC:2010 CONTENTS FORE WORD 3 INTRODUCTION 5 1 Scop e 6 2 Normative references 6 3 Terms, definitions and abbreviations. 6 3.1 Terms and definitions . 6 3.2 Abbreviations . 6 4 Classification

19、 . 6 5 Specification of the optical connector interface 7 6 Electrical interface 7 6.1 Gene ra l . 7 6.2 Numbering of electrical terminals . 7 6.3 Electrical terminal assignment . 7 7 Outline and footprint . 8 7.1 Drawings of case outline . 8 7.2 Optical receptacle 14 7.3 Drawings of case footprint

20、. 15 Figure 1 Electrical terminal numbering assignments (viewed from above with pins underneath) . 7 Figure 2 Case outline of the SFF MT-RJ 10-pin transceiver 9 Figure 3 Case outline of the SFF LC 10-pin transceiver . 11 Figure 4 Case outline of the SFF MU duplex 10-pin transceiver 13 Figure 5 Case

21、footprint . 15 Table 1 Transceiver receiver pin-function definitions . 7 Table 2 Transceiver transmitter pin-function definitions . 8 Table 3 Key to Figure 2 10 Table 4 Key to Figure 3 12 Table 5 Key to Figure 4 14 Table 6 Key to Figure 5 16 62148-2 IEC:2010 3 INTERNATIONAL ELECTROTECHNICAL COMMISSI

22、ON _ FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES PACKAGE AND INTERFACE STANDARDS Part 2: SFF 10-pin transceivers FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees)

23、. The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Sp

24、ecifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizat

25、ions liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matte

26、rs express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

27、 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC

28、National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself

29、does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they

30、 have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature wh

31、atsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publ

32、ications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International St

33、andard IEC 62148-2 has been prepared by subcommittee 86C: Fibre optic systems and active devices, of IEC technical committee 86: Fibre optics. This standard should be read in conjunction with IEC 62148-1. This second edition cancels and replaces the first edition published in 2003. It constitutes a

34、technical revision. With respect to the previous edition, this edition includes 10-pin SFF-LC, and SFF MU devices. It also cancels and replaces the first edition of IEC 62148-7 and the first edition of IEC 62148-9. 4 62148-2 IEC:2010 The text of this standard is based on the following documents: FDI

35、S Report on voting 86C/975/FDIS 86C/981/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 62148 se

36、ries can be found, under the general title Fibre optic active components and devices Package and interface standards, on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore

37、.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 62148-2 IEC:2010 5 INTRODUCTION Fibre optic transceivers are used to convert electrical signals into optical signals and vice versa. This

38、 standard covers the physical interface for a 10-pin small form factor (SFF) transceiver. This transceiver is designed for use with the SFF MU/MT-RJ/LC duplex optical connector and with through-hole printed circuit-board applications. 6 62148-2 IEC:2010 FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES PACK

39、AGE AND INTERFACE STANDARDS Part 2: SFF 10-pin transceivers 1 Scope This part of IEC 62148 covers the physical interface specifications for the SFF MT-RJ/LC/MU duplex 10-pin fibre optic transceiver module family. The intent of this standard is to adequately specify the physical requirements of an op

40、tical transceiver that will enable mechanical interchangeability of transceivers complying with this standard both at the printed circuit wiring board and for any panel-mounting requirement. 2 Normative references The following referenced documents are indispensable for the application of this docum

41、ent. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61754-6, Fibre optic connector interfaces Part 6: Type MU connector family IEC 61754-18, Fibre optic connector interfaces Part 18:

42、Type MT-RJ connector family IEC 61754-20, Fibre optic connector interfaces Part 20:Type LC connector family IEC 62148-1, Fibre optic active components and devices Package and interface standards Part 1: General and guidance 3 Terms, definitions and abbreviations For the purposes of this document, th

43、e following terms, definitions and abbreviations apply. 3.1 Terms and definitions 3.1.1 small form factor optical transceiver a compact optical digital signal transceiver whose package has the same cross sectional outline as the receptacle of an electrical connector compliant with the IEC 60603-7 se

44、ries 3.2 Abbreviations SFF small form factor 4 Classification The transceiver described in this standard is classified as type 1 according to IEC 62148-1. 62148-2 IEC:2010 7 5 Specification of the optical connector interface This standard applies to the MT-RJ/LC/MU duplex optical connector interface

45、. Detailed dimensions of the optical receptacle are provided in Clause 7. Assignment of the optical transmit and receive ports is aligned to the electrical pins. One-half of the module is the transmit side and the other is the receive side. Assignments are shown in Figure 1. 6 Electrical interface 6

46、.1 General The electrical interface in this standard defines only the basic functionality of each pin. 6.2 Numbering of electrical terminals Pin numbering assignments are shown in Figure 1 (viewed from the top of the module with pins underneath). Key Rx: receiver section Tx: transmitter section Figu

47、re 1 Electrical terminal numbering assignments (viewed from above with pins underneath) 6.3 Electrical terminal assignment Table 1 Transceiver receiver pin-function definitions 10-pin part Symbol Functional description MSaMS Mounting studs The mounting studs are provided for transceiver mechanical a

48、ttachment to the circuit board. They may also provide an optional connection of the transceiver to the equipment chassis ground HL HL Housing leads The optional transceiver housing leads may be provided for additional signal grounding. These additional grounds may improve signal integrity, EMC or EM

49、I performance 1 Vee r Receiver signal ground 2 Vcc r Receiver power supply 3 SD Signal detect 4 RD- Received data out bar 5 RD+ Received data out a The holes in the circuit board shall be tied to the chassis ground. 1 2 3 4 5 HL 10 9 8 7 6 HL Tx Rx MS HL MS HL IEC 2853/10 8 62148-2 IEC:2010 Table 2 Transceiver transmitter pin-function definitions 10-pin part Symbol Fu