IEC 61375-3-2-2012 Electronic railway equipment - Train Communication Network (TCN) - Part 3-2 MVB (Multifunction Vehicle Bus) conformance testing《电子铁路设备.列车通讯网络(TCN).第3-2部分 MVB(多功能列车总线)》.pdf

《IEC 61375-3-2-2012 Electronic railway equipment - Train Communication Network (TCN) - Part 3-2 MVB (Multifunction Vehicle Bus) conformance testing《电子铁路设备.列车通讯网络(TCN).第3-2部分 MVB(多功能列车总线)》.pdf》由会员分享，可在线阅读，更多相关《IEC 61375-3-2-2012 Electronic railway equipment - Train Communication Network (TCN) - Part 3-2 MVB (Multifunction Vehicle Bus) conformance testing《电子铁路设备.列车通讯网络(TCN).第3-2部分 MVB(多功能列车总线)》.pdf（212页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61375-3-2 Edition 1.0 2012-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Electronic railway equipment Train communication network (TCN) Part 3-2: MVB (Multifunction Vehicle Bus) conformance testing Matriel lectronique ferroviaire Rseau embarqu de train (TCN) Partie 3-2: Essais de conformit MVB

2、 (Bus de Vhicule Multifonctions) IEC 61375-3-2:2012 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mech

3、anical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the ad

4、dress below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la pho

5、tocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national

6、de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes I

7、nternational Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful

8、 links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/ju

9、stpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 ter

10、ms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, pleas

11、e contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des

12、 publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet d

13、e trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CE

14、I. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en

15、franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: c

16、sciec.ch. IEC 61375-3-2 Edition 1.0 2012-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Electronic railway equipment Train communication network (TCN) Part 3-2: MVB (Multifunction Vehicle Bus) conformance testing Matriel lectronique ferroviaire Rseau embarqu de train (TCN) Partie 3-2: Essais de conf

17、ormit MVB (Bus de Vhicule Multifonctions) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XD ICS 45.060 PRICE CODE CODE PRIX ISBN 978-2-88912-071-0 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechniqu

18、e Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 61375-3-2 IEC:2012 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope . 8 2 Normative re

19、ferences . 8 3 Terms and definitions . 9 4 Conformance test: approach, requirements and boundaries . 9 4.1 Approach . 9 4.1.1 Requirements 9 4.1.2 Requirements declaration statements for an IUT . 11 4.2 Boundaries 12 4.2.1 General . 12 4.2.2 Basic interconnection tests 13 4.2.3 Capability tests 13 4

20、.2.4 Behaviour tests 14 4.2.5 Conformance resolution tests 14 4.2.6 Interpretation of clauses/subclauses and statements . 15 4.2.7 Relation to interoperability . 17 4.2.8 Relation to performance test 17 4.3 Conformance assessment process outline . 18 4.3.1 General . 18 4.3.2 Analysis of results, out

21、comes and verdicts 18 5 Conformance test of an MVB device . 19 5.1 PICS . 19 5.1.1 Instructions for filling the PICS pro-forma 19 5.1.2 PICS tables . 21 5.2 Test suites 29 5.2.1 Basic interconnection tests 29 5.2.2 Capability tests 30 5.2.3 Behavioural tests . 31 5.2.4 Electrical short distance medi

22、um . 31 5.2.5 Electrical middle distance medium . 35 5.2.6 Slave device status test suites . 40 5.2.7 Process data test suites 48 5.2.8 Slave message data capability test suite . 60 5.2.9 MVB repeater conformance tests . 77 6 Conformance test of RTP . 86 6.1 General . 86 6.2 Ports and Traffic_Store

23、. 86 6.3 Dataset consistency 86 6.3.1 Error handling 87 6.3.2 Freshness supervision . 87 6.3.3 Synchronisation dataset 87 6.3.4 Dataset polling 87 6.3.5 Dataset, port and logical address 87 6.3.6 Traffic_Store Identifier . 87 61375-3-2 IEC:2012 3 6.4 Port_Address 88 6.5 Link_Process_Data_Interface p

24、rimitives 88 6.6 Messages services and protocols 88 7 Conformance test of NM . 88 Annex A (normative) Test laboratory role and client role 89 Annex B (informative) Test instrumentation and dedicated test beds 96 Bibliography 98 Figure 1 Application of the waveshaper 29 Figure 2 ESD test layout 31 Fi

25、gure 3 ESD terminator connector test . 33 Figure 4 ESD waveform measurement . 34 Figure 5 Measurement of an EMD device . 36 Figure 6 Measurement of insertion loss 37 Figure 7 EMD transmitter test circuits 38 Figure 8 Example of test hardware implementation 49 Figure 9 F_code + Address 54 Figure 10 C

26、oncept of message data testing . 60 Figure 11 Model of the relation between TE and IUT for message data testing 61 Figure 12 Relation between TE and IUT in case of test of IUT as caller . 61 Figure 13 Packet formats (transport layer body) . 62 Figure 14 Test message task of IUT . 63 Figure 15 Caller

27、 timeout identification 66 Figure 16 Nesting address with 0x83 . 71 Figure 17 Block diagram of a line . 77 Figure 18 Frames in test RP-1.2 78 Figure 19 Inter-frame spacing 79 Figure 20 Pulse distortion 80 Figure 21 Frame with out-of-place transition 80 Figure 22 Frames in test RP-1.4 81 Figure B.1 T

28、est bed configuration MRTB1 96 Figure B.2 Test bed configuration MRTB2 97 Table 1 Document structure . 7 Table 2 Continuance indication 16 Table 3 Weak statements . 17 Table 4 Relation to interoperability . 17 Table 5 Relation to performance test . 17 Table 6 ESD basic interconnection tests 30 Table

29、 7 EMD basic interconnection tests . 30 Table 8 Measurement idle 32 Table 9 Measurement with load for minimum current . 32 Table 10 Measurement with load for maximum current . 32 4 61375-3-2 IEC:2012 Table 11 Measurement with load for overcurrent 33 Table 12 ESD measurements pin to pin . 33 Table 13

30、 Event poll strategy. 64 Table 14 Abbreviations 68 Table 15 Addressing type 68 Table 16 Test function directory . 70 Table 17 Test station directory . 71 Table 18 Nesting address 72 Table 19 Read_Memory and Write_Memory sequence . 73 Table 20 Configuration of periodic data in BA 84 Table 21 Configur

31、ation of periodic ports in CU-1 84 Table 22 Configuration of periodic ports in CU-2 85 61375-3-2 IEC:2012 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRONIC RAILWAY EQUIPMENT TRAIN COMMUNICATION NETWORK (TCN) Part 3-2: MVB (Multifunction Vehicle Bus) conformance testing FOREWORD 1) The Interna

32、tional Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electro

33、nic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees;

34、 any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Stan

35、dardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has r

36、epresentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate,

37、 IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional pu

38、blications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some a

39、reas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents incl

40、uding individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reli

41、ance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the e

42、lements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61375-3-2 has been prepared by IEC Technical Committee 9: Electrical equipment and systems for railways. This first edition

43、 cancels the clauses of the IEC 61375-2 first edition published in 2007 relevant to the specification of MVB conformance testing and constitutes a technical revision. It was prepared taking into account the IEC 61375-3-1 first edition. 6 61375-3-2 IEC:2012 The text of this standard is based on the f

44、ollowing documents: FDIS Report on voting 9/1645/FDIS 9/1669/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all part

45、s of IEC 61375 series, under the general title Electronic railway equipment Train communication network (TCN), can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/we

46、bstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to b

47、e useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 61375-3-2 IEC:2012 7 INTRODUCTION TCN is an International Standard with the aim of defining interfaces so as to achieve plug-in compatibility: a) between equipment located in di

48、fferent vehicles, and b) between equipment and devices located within the same vehicle. One of the key success factors for the deployment of any technology is standardisation and ensuring interoperability among various implementations. To facilitate interoperability a conformance test should be impl

49、emented. In this part of IEC 61375, the conformace testing of the MVB defined in IEC 61375-3-1 is specified. This standard is structured into 5 clauses and 2 annexes. The clauses and annexes are listed and briefly described in Table 1. Table 1 Document structure Clause Description 1 Scope This clause describes the scope of this standa