IEC 60364-5-55 Edition 2.1-2012 Electrical installations of buildings - Part 5-55 Selection and erection of electrical equipment - Other equipment《建筑物的电气设施.第5-55部分 电气设备的选择和安装.其他设备》.pdf

《IEC 60364-5-55 Edition 2.1-2012 Electrical installations of buildings - Part 5-55 Selection and erection of electrical equipment - Other equipment《建筑物的电气设施.第5-55部分 电气设备的选择和安装.其他设备》.pdf》由会员分享，可在线阅读，更多相关《IEC 60364-5-55 Edition 2.1-2012 Electrical installations of buildings - Part 5-55 Selection and erection of electrical equipment - Other equipment《建筑物的电气设施.第5-55部分 电气设备的选择和安装.其他设备》.pdf（78页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60364-5-55 Edition 2.1 2012-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Electrical installations of buildings Part 5-55: Selection and erection of electrical equipment Other equipment Installations lectriques des btiments Partie 5-55: Choix et mise en oeuvre des matriels lectriques Autres ma

2、triels IEC 60364-5-55:2011+A1:2012 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including

3、 photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or yo

4、ur local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les mi

5、crofilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votr

6、e pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Stan

7、dards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publi

8、cations search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay

9、up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definition

10、s in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Cus

11、tomer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI

12、 Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des pub

13、lications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published

14、 dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi qu

15、e les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 603

16、64-5-55 Edition 2.1 2012-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Electrical installations of buildings Part 5-55: Selection and erection of electrical equipment Other equipment Installations lectriques des btiments Partie 5-55: Choix et mise en oeuvre des matriels lectriques Autres matriels I

17、NTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE CM ICS 91.140 PRICE CODE CODE PRIX ISBN 978-2-8322-0426-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that yo

18、u obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 60364-5-55 IEC:2011+A1:2012 CONTENTS FOREWORD . 4 550 Introduction . 6 550.1 Scope 6 550.2 Normative references . 6 550.3 Terms

19、 and definitions . 8 551 Low-voltage generating sets 8 551.1 Scope 8 551.2 General requirements .9 551.3 Protective measure: extra-low-voltage provided by SELV and PELV . 10 551.4 Fault protection (protection against indirect contact) . 10 551.5 Protection against overcurrent . 11 551.6 Additional r

20、equirements for installations where the generating set provides a supply as a switched alternative to the normal supply to the installation . 12 551.7 Additional requirements for installations where the generating set may operate in parallel with other sources including systems for distribution of e

21、lectricity to the public 12 551.8 Requirements for installations incorporating stationary batteries 14 557 Auxiliary circuits 14 557.1 Scope 14 557.2 Terms and definitions 14 557.3 Requirements for auxiliary circuits . 15 557.4 Characteristics of cables and conductors Minimum cross-sectional areas 1

22、8 557.5 Requirements for auxiliary circuits used for measurement 19 557.6 Functional consideration 19 557.7 Functional safety 22 557.8 EMC . 22 559 Luminaires and lighting installations 22 559.1 Scope 22 559.2 Terms and definitions 22 559.3 General requirements for installations . 23 559.4 Protectio

23、n of the surroundings against thermal effects . 23 559.5 Wiring systems for lighting installations . 24 559.6 Independent lamp controlgear, e.g. ballasts 25 559.7 Compensation capacitors 25 559.8 Protection against electric shock for display stands for luminaires . 26 559.9 Stroboscopic effect 26 55

24、9.10 Ground recessed luminaires 26 Annex A (informative) List of notes concerning certain countries 27 Annex B (informative) Explanation of symbols used in luminaires, in controlgear for luminaires and in the installation of the luminaires . 33 60364-5-55 IEC:2011+A1:2012 3 Bibliography 35 Figure 55

25、7.1 Auxiliary circuit supplied directly from the main circuit . 15 Figure 557.2 Auxiliary circuit supplied via rectifier from the main circuit . 16 Figure 557.3 Auxiliary circuit supplied from the main circuit via transformer . 16 Figure 557.4 Configuration of an auxiliary circuit 21 Table 557.1 Min

26、imum cross-sectional area of copper conductors in mm 2. 18 4 60364-5-55 IEC:2011+A1:2012 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRICAL INSTALLATIONS OF BUILDINGS Part 5-55: Selection and erection of electrical equipment Other equipment FOREWORD 1) The International Electrotechnical Commissi

27、on (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in a

28、ddition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee inte

29、rested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance

30、with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all intereste

31、d IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible

32、for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence betwe

33、en any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of con

34、formity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and mem

35、bers of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication

36、or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication

37、may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. This consolidated version of IEC 60364-5-55 consists of the second edition (2011) documents 64/1805/FDIS and 64/1813/RVD and its amendment 1 (2012) documents 64/1831/FDIS and 64/1863

38、/RVD. It bears the edition number 2.1. The technical content is therefore identical to the base edition and its amendment and has been prepared for user convenience. A vertical line in the margin shows where the base publication has been modified by amendment 1. Additions and deletions are displayed

39、 in red, with deletions being struck through. 60364-5-55 IEC:2011+A1:2012 5 International Standard IEC 60364-5-55 has been prepared by IEC technical committee 64: Electrical installations and protection against electric shock. The major technical changes with respect to the previous edition are list

40、ed below: additional requirements for connection of luminaires to the fixed wiring; modification of requirements regarding the fixing of luminaires; inclusion of alternative solutions for connecting devices used for through wiring and for connection of luminaires to the supply; withdrawal of Clause

41、556, as IEC 60364-5-56 now covers this matter. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60364 series, under the general title Low-voltage electrical installations, can be found on the IEC website. The committee has decided th

42、at the contents of the base publication and its amendments will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised e

43、dition, or amended. IMPORTANT The “colour inside” logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this publication using a colour printer. 6 60364-5-55 IEC:2011

44、+A1:2012 ELECTRICAL INSTALLATIONS OF BUILDINGS Part 5-55: Selection and erection of electrical equipment Other equipment 550 Introduction 550.1 Scope This part of IEC 60364 covers requirements for the selection and erection of low-voltage generating sets and for the selection and erection of luminai

45、res and lighting installations intended to be part of the fixed installation. 550.2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the

46、referenced document (including any amendments) applies. IEC 60038, IEC standard voltages IEC 60050-195, International Electrotechnical Vocabulary Part 195: Earthing and protection against electric shock IEC 60050-826, International Electrotechnical Vocabulary Part 826: Electrical installations IEC 6

47、0079 (all parts), Explosive atmospheres IEC 60245-3, Rubber insulated cables Rated voltages up to and including 450/750 V Part 3: Heat resistant silicone insulated cables IEC 60331-11, Tests for electric cables under fire conditions Circuit integrity Part 11: Apparatus Fire alone at a flame temperat

48、ure of at least 750 C IEC 60331-21, Tests for electric cables under fire conditions Circuit integrity Part 21: Procedures and requirements Cables of rated voltage up to and including 0,6/1,0 kV IEC 60364-1:2005, Low-voltage electrical installations Part 1: Fundamental principles, assessment of gener

49、al characteristics, definitions IEC 60364-4-41:2005, Low-voltage electrical installations Part 4-41: Protection for safety Protection against electric shock IEC 60364-4-42, Low-voltage electrical installations Part 4-42: Protection for safety Protection against thermal effects IEC 60364-4-43:2008, Low-voltage electrical installations Part 4-43: Protection for safety Protect