IEC 60335-2-30-2009 Household and similar electrical appliances - Safety - Part 2-30 Particular requirements for room heaters《家用及类似用途电器.安全性.第2-30部分 房间取暖器的详细要求》.pdf

《IEC 60335-2-30-2009 Household and similar electrical appliances - Safety - Part 2-30 Particular requirements for room heaters《家用及类似用途电器.安全性.第2-30部分 房间取暖器的详细要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 60335-2-30-2009 Household and similar electrical appliances - Safety - Part 2-30 Particular requirements for room heaters《家用及类似用途电器.安全性.第2-30部分 房间取暖器的详细要求》.pdf（66页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60335-2-30 Edition 5.0 2009-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Household and similar electrical appliances Safety Part 2-30: Particular requirements for room heaters Appareils lectrodomestiques et analogues Scurit Partie 2-30: Exigences particulires pour les appareils de chauffage d

2、es locaux IEC 60335-2-30:2009 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and m

3、icrofilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member

4、 National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans lacc

5、ord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence.

6、 IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all elect

7、rical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - ww

8、w.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all n

9、ew IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and Fr

10、ench, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centr

11、e: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu techniq

12、ue des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en ut

13、ilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvel

14、les publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quival

15、ents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60335-2-30 Edition 5.0

16、 2009-11 INTERNATIONAL STANDARD NORME INTERNATIONALE Household and similar electrical appliances Safety Part 2-30: Particular requirements for room heaters Appareils lectrodomestiques et analogues Scurit Partie 2-30: Exigences particulires pour les appareils de chauffage des locaux INTERNATIONAL ELE

17、CTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 13.120; 97.100.10 PRICE CODE CODE PRIX ISBN 978-2-83220-357-6 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obta

18、ined this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60335-2-30 IEC:2009 CONTENTS FOREWORD . 3 INTRODUCTION . 6 1 Scope . 7 2 Normative references . 8 3 Definitions 8 4 General requirement . 9 5 Gener

19、al conditions for the tests 9 6 Classification 10 7 Marking and instructions . 10 8 Protection against access to live parts 13 9 Starting of motor-operated appliances 14 10 Power input and current . 14 11 Heating 14 12 Void 16 13 Leakage current and electric strength at operating temperature 16 14 T

20、ransient overvoltages . 16 15 Moisture resistance 17 16 Leakage current and electric strength . 17 17 Overload protection of transformers and associated circuits . 17 18 Endurance 17 19 Abnormal operation 17 20 Stability and mechanical hazards . 21 21 Mechanical strength . 21 22 Construction . 22 23

21、 Internal wiring . 24 24 Components . 24 25 Supply connection and external flexible cords 25 26 Terminals for external conductors . 25 27 Provision for earthing . 25 28 Screws and connections . 25 29 Clearances, creepage distances and solid insulation 25 30 Resistance to heat and fire . 25 31 Resist

22、ance to rusting 26 32 Radiation, toxicity and similar hazards 26 Annexes . 29 Bibliography 30 Figure 101 Examples of immediate surrounds of air-outlet grilles . 27 Figure 102 Examples of the immediate surrounds of fireguards . 28 Table 101 Temperature rises for surfaces 16 60335-2-30 IEC:2009 3 INTE

23、RNATIONAL ELECTROTECHNICAL COMMISSION _ HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES SAFETY Part 2-30: Particular requirements for room heaters FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical comm

24、ittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technica

25、l Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental

26、 and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agre

27、ements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use

28、and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promot

29、e international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicat

30、ed in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) A

31、ll users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage

32、or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publica

33、tion. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such

34、 patent rights. International Standard IEC 60335-2-30 has been prepared by IEC technical committee 61: Safety of household and similar electrical appliances. This fifth edition cancels and replaces the fourth edition published in 2002, its Amendment 1 (2004) and Amendment 2 (2007). It constitutes a

35、technical revision. The principal changes in this edition as compared with the fourth edition of IEC 60335-2-30 are as follows (minor changes are not listed): some additional instructions are introduced for heaters without a built-in thermostat, or those installed in the floor or in a bathroom (7.12

36、 and 7.12.1); a spillage test is introduced for appliances having a grille and that are built into the floor (15.2). This bilingual version (2012-09) corresponds to the monolingual English version, published in 2009-11. 4 60335-2-30 IEC:2009 The text of this standard is based on the following docume

37、nts: FDIS Report on voting 61/3910/FDIS 61/3957/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with th

38、e ISO/IEC Directives, Part 2. This part 2 is to be used in conjunction with the latest edition of IEC 60335-1 and its amendments. It was established on the basis of the fourth edition (2001) of that standard. NOTE 1 When “Part 1” is mentioned in this standard, it refers to IEC 60335-1. This part 2 s

39、upplements or modifies the corresponding clauses in IEC 60335-1, so as to convert that publication into the IEC standard: Safety requirements for room heaters. When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as far as is reasonable. When this standard st

40、ates “addition“, “modification“ or “replacement“, the relevant text in Part 1 is to be adapted accordingly. NOTE 2 The following numbering system is used: subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; unless notes are in a new subclause or invo

41、lve notes in Part 1, they are numbered starting from 101, including those in a replaced clause or subclause; additional annexes are lettered AA, BB, etc. NOTE 3 The following print types are used: requirements: in roman type; test specifications: in italic type; notes: in small roman type. Words in

42、bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are also in bold. The committee has decided that the contents of the base publication and its amendments will remain unchanged until the maintenance result date indicated on the I

43、EC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. NOTE 4 The attention of National Committees is drawn to the fact that equipment manufacturers and testin

44、g organizations may need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content

45、of this publication be adopted for implementation nationally not earlier than 12 months or later than 36 months from the date of publication. 60335-2-30 IEC:2009 5 The following differences exist in the countries indicated below. 3.105: The immediate surround of a fireguard is extended to 50 mm (Aus

46、tria, Germany and United Kingdom). 7.1: All heaters, except those for mounting at high level, are to be marked with a warning against covering (Norway). 7.1: All heaters, except those for permanent connection to fixed wiring, are to be marked with the minimum distances to combustible surfaces (Norwa

47、y). 7.1: Appliances are not required to be marked “Do not cover“ (USA). 7.12: Some of the instructions specified are to be marked on the heater (Norway and USA). Clause 11: The test methods are different (USA). 11.8: For other metal surfaces accessible to the test rod, the limit is 95 K (Australia).

48、 11.8: For all fixed heaters, other than those for mounting at high level, the limit is 115 K for metallic air-outlet grilles and their surrounds (France). 11.8: For heaters used in hygiene rooms of dwellings, nurseries or after-school centres, the temperatures of surfaces accessible to test probe B

49、 of IEC 61032 are not to exceed 60 C (Sweden). Clause 19: The tests are different (Canada and USA). 19.103: Visibly glowing radiant heaters, other than those for mounting at high level, have to withstand the test of this subclause (Sweden). 20.1: The test is different (USA). 22.7: The test is different (USA). 22.24: The test is different (USA). 22.101: The requirement is different (Canada and USA