TIA-568-B 2-6-2003 Commercial Building Telecommunications Cabling Standard Part 2 Balanced Twisted Pair Cabling Components Addendum 6 Category 6 Related Component Test Procedures A.pdf

《TIA-568-B 2-6-2003 Commercial Building Telecommunications Cabling Standard Part 2 Balanced Twisted Pair Cabling Components Addendum 6 Category 6 Related Component Test Procedures A.pdf》由会员分享，可在线阅读，更多相关《TIA-568-B 2-6-2003 Commercial Building Telecommunications Cabling Standard Part 2 Balanced Twisted Pair Cabling Components Addendum 6 Category 6 Related Component Test Procedures A.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA STANDARD Commercial Building Telecommunications Cabling Standard Part 2: Balanced Twisted Pair Cabling Components Addendum 6 Category 6 Related Component Test Procedures TIA-568-B.2-6 (Supplement to TIA568-B.2) DECEMBER 2003 TELECOMMUNICATIONS INDUSTRY ASSOCIATION Representing the telecommunica

2、tions industry in association with the Electronic Industries Alliance ANSI/TIA-568-B.2-6 2003 Approved: December 23, 2003 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE

3、TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the

4、proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Pub

5、lications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, n

6、or does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate s

7、afety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-4426-AD6, formulated under the cognizance of the TIA TR-42 Committee on User Premises Telecommunications Infrastructure.) Published by TELECOMMUNICATIONS INDUSTRY AS

8、SOCIATION 2002 Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) Inter

9、national (303-397-7956) or search online at http:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IH

10、S-,-,-PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the TIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 I

11、nverness Way East Englewood, CO 80112-5704 U.S.A. or call U.S.A. and Canada 1-800-854-7179, International (303) 397-7956 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE O

12、F DISCLAIMER AND LIMITATION OF LIABILITY The document to which this Notice is affixed has been prepared by one or more Engineering Committees of the Telecommunications Industry Association (“TIA”). TIA is not the author of the document contents, but publishes and claims copyright to the document pur

13、suant to licenses and permission granted by the authors of the contents. TIA Engineering Committees are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor versions of which are available at http:/www.tiaonline.org/standards/sfg/eng

14、ineering_manual.cfm. TIAs function is to administer the process, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). THE USE OR PRACTICE OF CONTENTS OF THIS DOCUMENT MAY I

15、NVOLVE THE USE OF INTELLECTUAL PROPERTY RIGHTS (“IPR”), INCLUDING PENDING OR ISSUED PATENTS, OR COPYRIGHTS, OWNED BY ONE OR MORE PARTIES. TIA MAKES NO SEARCH OR INVESTIGATION FOR IPR. WHEN IPR CONSISTING OF PATENTS AND PUBLISHED PATENT APPLICATIONS ARE CLAIMED AND CALLED TO TIAS ATTENTION, A STATEME

16、NT FROM THE HOLDER THEREOF IS REQUESTED, ALL IN ACCORDANCE WITH THE MANUAL. TIA TAKES NO POSITION WITH REFERENCE TO, AND DISCLAIMS ANY OBLIGATION TO INVESTIGATE OR INQUIRE INTO, THE SCOPE OR VALIDITY OF ANY CLAIMS OF IPR. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATI

17、ON, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF

18、THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMI

19、TATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE

20、 POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for Resal

21、eNo reproduction or networking permitted without license from IHS-,-,-Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-568-B.2-6 i CATEGORY 6 RELATED COMPONENT TEST PROCEDURE

22、S TABLE OF CONTENTS 1 INTRODUCTION.1 2 PURPOSE AND SCOPE.1 3 CATEGORY 6 MEASUREMENT REFINEMENTS .1 3.1 Table E.3 replacement 1 3.2 Further clause E.3.2.2 revisions . 2 3.3 Clause E.3.2.5 revisions . 2 3.4 Annex H replacement . 3 3.5 Annex J revisions 4 Copyright Telecommunications Industry Associati

23、on Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-568-B.2-6 1 1 INTRODUCTION After publication of the TIA-568-B.2-1 standard, the TR-42.7 UTP Systems Sub-Committee identified refinements and enhancements that result in imp

24、roved category 6 measurement accuracy and repeatability. The purpose of this addendum is to recognize refinements and enhancements that result in improved category 6 measurement accuracy and repeatability by revising clause E.3.2.2, clause E.3.2.5, annex H, annex J.3, and annex J.4 of TIA-568-B.2-1.

25、 2 PURPOSE AND SCOPE The following clauses contain refinements and enhancements to the measurement methods specified for category 6 components in the TIA-568-B.2-1 standard. 3 CATEGORY 6 MEASUREMENT REFINEMENTS 3.1 Table E.3 replacement Replace the existing table E.3 with the following new table: Ta

26、ble E.3 Category 6 de-embedded test plug NEXT loss ranges Pair combination NEXT loss magnitude range 1),4),5)NEXT loss phase range 2),3)3,6-4,5 36.4-20log(f/100) NEXT loss 37.6-20log(f/100) 50 100 MHz: (-90 + 1.5f/100) 1 100 250 MHz: (-90 + 1.5f/100) f/100 1,2-3,6 46.5-20log(f/100) NEXT loss 49.5-20

27、log(f/100) (-90 +1.5f/100) 3f/100 3,6-7,8 46.5-20log(f/100) NEXT loss 49.5-20log(f/100) (-90 +1.5f/100) 3f/100 1,2-4,5 7)NEXT loss 57-20log(f/100) 90 (30f/100)6)4,5-7,8 7)NEXT loss 57-20log(f/100) 90 (30f/100) 6)1,2-7,8 NEXT loss 60-20log(f/100) Any phase 1) Magnitude limits apply over the frequency

28、 range from 10 MHz to 250 MHz. 2) Phase limits apply over the frequency range from 50 MHz to 250 MHz. 3) When the measured plug NEXT loss is greater than 70 dB, the phase limit does not apply. 4) When a high limit NEXT loss calculation results in values greater than 70 dB, there shall be no high lim

29、it for NEXT loss. Refer to Table E.2 for an explanation of the high limit. 5) When a low limit NEXT loss calculation results in values greater than 70 dB, the low limit shall revert to 70 dB. Refer to table E.2 for an explanation of the low limit. 6) When the NEXT loss magnitude exceeds 70 20 log (f

30、/100), the phase requirement does not apply. 7) The requirements for 1-2,4-5 and 4,5-7,8 do not exclude plugs that meet cases 9 and 11, respectively, shown in table E.2, because such plugs are acceptable for field tester adapters. Copyright Telecommunications Industry Association Provided by IHS und

31、er license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-568-B.2-6 2 3.2 Further clause E.3.2.2 revisions Add the following new sentence and table after table E.3 and its corresponding note: In addition, the de-embedded test plug FEXT loss performance

32、 for all pair combinations shall satisfy the ranges shown in table E.3.1. Table E.3.1 FEXT loss ranges for category 6 NEXT loss test plugs Pair combination Frequency range (MHz) FEXT loss3), 4) magnitude range (dB) Phase 1), 2)(degrees) 3,6-4,5 10-250 46-20log(f/100) FEXT loss 56-20log(f /100) -90 (

33、30 f /100) 1,2-3,6 10-250 46-20log(f /100) FEXT loss 56-20log(f /100) -90 (30 f /100) 3,6-7,8 10-250 46-20log(f /100) FEXT loss 56-20log(f /100) -90 (30 f /100) 1,2-4,5 10-250 55-20log(f /100) any phase 4,5-7,8 10-250 55-20log(f /100) any phase 1,2-7,8 10-250 55-20log(f /100) any phase 1) When the m

34、easured plug FEXT loss is greater than 70 dB, the phase requirement does not apply. 2) Due to measurement accuracy considerations, phase measurement requirements below 50 MHz are specified for information only. 3) When upper limit FEXT loss calculations result in values greater than 70 dB, there sha

35、ll be no upper limit for FEXT loss. 4) When lower limit FEXT loss calculations result in values greater than 70 dB, the lower limit FEXT shall revert to a limit of 70 dB. 3.3 Clause E.3.2.5 revisions After table E.4, add the following: NOTE - It is recommended that connecting hardware FEXT loss shou

36、ld be characterized through measurement or calculation throughout the allowable FEXT loss test plug range for each pair combination. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-

37、,-,-TIA-568-B.2-6 3 3.4 Annex H replacement The following method has been identified as a refined procedure for selecting reference jacks. The following text should replace all of the text currently appearing in annex H of TIA-568-B.2. Annex H De-embedding reference NEXT loss jack selection procedur

38、e (normative) H.1 Scope The performance of a particular laboratory de-embedded reference NEXT jack design can be compared to the reference jack vectors specified in clause E.3.2.1 by using the de-embedding procedures specified in clause D.5 of TIA-568-B.2. The procedure described in this annex defin

39、es a figure of merit for the consistency of the reference jack. The reference jack used to measure test plugs shall be within the best 25 % of at least 20 reference jacks measured on all pair combinations. This will minimize the measurement variance due to the variance within a lot of jacks. H.2 Mea

40、surement sampling plan The de-embedding procedures specified in clause D.5 of TIA-568-B.2 should be used to measure the reference jacks. The performance of a particular laboratory de-embedded reference jack shall be verified by determining the mated NEXT loss vector of multiple jack samples using on

41、e reference plug. A reference jack sample size of at least 20 pieces shall be measured. A reference jack sample size of at least 30 pieces should be measured. From these 30 pieces, 20 pieces should be selected that exclude the pieces causing the largest deviation from the average performance that is

42、 obtained as described below. The figure of merit shall be determined as follows: 1. Build a reference plug according to the instructions of annex D.5 of TIA- 568-B.2. 2. For each pair combination, do the following: 2.1. Measure real and imaginary NEXT of the mated reference plug and reference jack

43、between 10 MHz and 250 MHz. 2.2. Calculate the average of the mated reference plug and reference jack (RPRJ) real and imaginary parts for each frequency point. 2.3. Discard all real data points for all of the jacks where the average real RPRJ is less than 316 V/V. 2.4. Discard all imaginary data poi

44、nts for all of the jacks where the average imaginary RPRJ is less than 316 V/V 2.5. Calculate the difference between each RPRJ and the average RPRJ. The real and imaginary differences shall be calculated separately. 2.6. “Normalize“ the difference data by dividing each point by the frequency of meas

45、urement. 2.7. Square the normalized data. Square the real and imaginary data separately. 2.8. Sum all squared data over the frequency range. 3. Compile the results for all pair combinations. 4. Sum the data for all pair combinations for each sample. This will yield a single number as a figure of mer

46、it for each reference jack. The selected reference jacks shall be the 25% of the sample set with the lowest merit value. The remaining jacks shall be discarded, and shall not be used in additional qualification procedures. Copyright Telecommunications Industry Association Provided by IHS under licen

47、se with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-568-B.2-6 4 3.5 Annex J revisions The material from “J.3 Modular plug cord test procedure” through the end of paragraph J.4, up to clause J.4.1, of TIA-568-B.2-1 shall be replaced by the following: J.3

48、Modular plug cord test procedure A minimum of 100 data points per decade shall be measured for each pair combination. Pass or fail qualification shall be determined by comparing the resulting sweeps to the NEXT loss limits calculated per clause 7.2.1.3 for the applicable frequency range. A minimum o

49、f 200 data points per decade is required to qualify modular plug cords longer than 10 m (32 ft). The pass or fail margin and the frequency at which it occurs shall be reported for each pair combination. In addition, modular plug cords shall be qualified for return loss according to the requirements of clause 7.4.4. J.4 Category 6 modular plug cord test h