SANS 6594-2008 Cast iron drainage pipes and fittings - Spigot series《铸铁排水管和配件 插口系列》.pdf

《SANS 6594-2008 Cast iron drainage pipes and fittings - Spigot series《铸铁排水管和配件 插口系列》.pdf》由会员分享，可在线阅读，更多相关《SANS 6594-2008 Cast iron drainage pipes and fittings - Spigot series《铸铁排水管和配件 插口系列》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21228-5 SANS 6594:2008Edition 1ISO 6594:2006Edition 2SOUTH AFRICAN NATIONAL STANDARD Cast iron drainage pipes and fittings Spigot series T

4、his national standard is the identical implementation of ISO 6594:2006 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 interna

5、tional code + 27 12 www.stansa.co.za Standards South Africa SANS 6594:2008 Edition 1 ISO 6594:2006 Edition 2 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee StanSA SC 5120.12C, Water and sanitation Equipment and systems Cast and

6、 ductile iron pipes and fittings, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in July 2008. Reference numberISO 6594:2006(E)ISO 2006INTERNATIONAL STANDARD ISO6594Second edition2006-03-15Cast iron drain

7、age pipes and fittings Spigot series Tuyaux et raccords salubres en fonte Srie bouts unis SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 6594:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordanc

8、e with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licens

9、ing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.

10、 Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2006 All rights reserved. Unless otherwise specified, no part of this publi

11、cation may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Genev

12、a 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2006 All rights reservedSANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 6594:2006(E) ISO 2006 All righ

13、ts reserved iiiContents Page Foreword iv Introduction v 1 Scope . 1 2 Normative references . 1 3 Technical specification 1 3.1 Type of ends and their jointing . 1 3.2 Quality of cast iron . 2 3.3 Quality of pipe and fittings 2 3.4 Marking 3 3.5 Range of nominal sizes 3 3.6 External diameters and tol

14、erances . 3 3.7 Thicknesses and tolerances 4 3.8 Lengths and tolerances 4 3.9 Tolerances on angles . 4 3.10 Masses and tolerances. 5 3.11 Protection 5 4 Dimensions 5 4.1 Pipe. 5 4.2 Fittings . 6 5 Control testing and test methods . 16 5.1 Testing of castings . 16 5.2 Testing coated products 17 5.3 Q

15、uality control. 17 5.4 Certificate 18 SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 6594:2006(E) iv ISO 2006 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of

16、 national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Int

17、ernational organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with t

18、he rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval

19、by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6594 was prepared by Technical Committee IS

20、O/TC 5, Ferrous metal pipes and metallic fittings, Subcommittee SC 2, Cast iron pipes, fittings and their joints. This second edition cancels and replaces the first edition (ISO 6594:1983), which has been technically revised. SANS 6594:2008This s tandard may only be used and printed by approved subs

21、cription and freemailing clients of the SABS .ISO 6594:2006(E) ISO 2006 All rights reserved vIntroduction The distinctive character of discharge pipelines is that products flow though them in a single direction under the force of gravity; they are thus laid on a slight slope in the direction of flow

22、. As a result, they include descending, vertical, oblique or slightly sipping components, but exclude any horizontal or ascending components. This International Standard consists of sections covering technical specifications, dimensions, and control and compliance testing. The technical specificatio

23、n applies to cast iron drainage pipes and fittings used for the discharge of waste water, sewage, rainwater and for ventilation. Thirteen of the nominal sizes used in various countries have been selected. NOTE The nominal size, DN, is a number which permits classification of the pipes and fittings;

24、it is only loosely related to the inside diameter. For the dimensions and masses, only the most commonly used sizes of the various pipes and fittings were selected. This International Standard does not exclude the use of sizes which may be specified in national standards. If the nominal masses of fi

25、nished products (pipes, fittings and accessories) are given in manufacturers catalogues, the lower deviation is not permitted to exceed the value specified in 3.10. The tests and controls provided in the final section are intended to be carried out to check compliance with the requirements given in

26、the other two sections. SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 6594:2006

27、(E) ISO 2006 All rights reserved 1Cast iron drainage pipes and fittings Spigot series 1 Scope This International Standard specifies the characteristics of cast iron drainage pipes and fittings used for the installation of: discharge pipes for waste and sewage, rain water pipe systems, and ventilatio

28、n pipe systems. The technical specification is applicable to the range of nominal sizes, DN: 40 50 70 75 100 125 150 200 250 300 400 500 600. Where applicable, national standards and/or regulations could clarify, and possibly restrict, the field of application of the pipes and fittings covered. In a

29、ddition, this International Standard gives the dimensions for the most commonly used pipe and fitting sizes. It also provides control testing and test methods for checking compliance with the technical specification and the dimensional and other requirements. 2 Normative references The following ref

30、erenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 185, Grey cast irons Classification 3 Technical specification

31、3.1 Type of ends and their jointing Cast iron drainage pipes and fittings are of the spigot type without sockets. The pipes and fittings may be assembled using various types of joints whose characteristics and tolerances shall be specified in the national standards or, failing these, in manufacturer

32、s catalogues. In order to achieve satisfactory assembly, each end shall present a free length corresponding at least to the values of Table 1. See Figure 1. SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 6594:2006(E) 2 ISO

33、2006 All rights reservedTable 1 Minimum free lengths Minimum free length l Nominal size DN mm 40 25 50 25 70a30 75a100 35 125 40 150 45 200 56 250 66 300 76 400 76 500 76 600 76 aThe range of nominal sizes and their classification differ slightly from one country to another. The use of DN 70 or DN 7

34、5 is subject to national standards or regulations. Figure 1 3.2 Quality of cast iron The quality of the type of cast iron used for drainage pipes and fittings shall be at least 150, in accordance with ISO 185, and have a phosphorous content of less than 0,9 %. 3.3 Quality of pipe and fittings Draina

35、ge pipes and fittings shall be sound and free from surface and other defects which would impair performance or service life. When fractured, the castings shall show a fine, grey, close and regular grain. Pipes and fittings with small imperfections that are unavoidable due to the manufacturing proces

36、ses and which are not harmful in any way to their usage shall not be rejected. Drainage pipes and fittings shall be capable of being cut with the tools normally used for installation. SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SA

37、BS .ISO 6594:2006(E) ISO 2006 All rights reserved 33.4 Marking Drainage pipes and fittings shall carry a durable manufactures mark. The pipes shall carry this manufacturers mark and the indication of the nominal diameter at least once per metre of length. Where possible, the fittings shall have thei

38、r nominal diameter and, if necessary, the angle of deviation, cast on. The marking shall be effected outside the region of the joint of the spigot (see 3.1). 3.5 Range of nominal sizes The range of nominal sizes is 1): 40 50 70 75 100 125 150 200 250 300 400 500 600 3.6 External diameters and tolera

39、nces The external diameters of drainage pipes and fittings and the tolerances applicable are given in Table 2. Table 2 External diameters and tolerances External diameter, DE, of pipe body Tolerance on external diameter, DE Nominal size DN mm mm 40 48 21+50 58 21+70a78 21+75a83 21+100 110 2 125 135

40、2 150 160 2 200 210 2,5 250 274 2,5 300 326 2,5 400 429 23+500 532 23,5+600 635 24+aThe range of nominal sizes and their classification differ slightly from one country to another. The use of DN 70 or DN 75 is subject to national standards or regulations. 1) The range of nominal sizes and their clas

41、sification differ slightly from one country to another. The use of DN 70 or DN 75 is subject to national standards or regulations. SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 6594:2006(E) 4 ISO 2006 All rights reserved3.

42、7 Thicknesses and tolerances Table 3 gives the minimum and nominal thicknesses of drainage pipes and fittings, spigot series. See Figure 2. Maximum thicknesses are not specified. Table 3 Nominal and minimum thicknesses of pipes and fittings Thickness e mm Pipe Fitting DN nom. min. nom. min 40 3,0 2,

43、5 3,7 2,5 50 3,5 3,0 4,2 3,0 70a3,5 3,0 4,2 3,0 75a3,5 3,0 4,2 3,0 100 3,5 3,0 4,2 3,0 125 4,0 3,5 4,7 3,5 150 4,0 3,5 5,3 3,5 200 5,0 4,0 6,0 4,0 250 5,5 4,5 7,0 4,5 300 6,0 5,0 8,0 5,0 400 6,3 5,0 8,3 5,0 500 7,0 5,2 9,0 5,2 600 7,7 5,8 9,7 5,8 aThe range of nominal sizes and their classification

44、differ slightly from one country to another. The use of DN 70 or DN 75 is subject to national standards or regulations. Figure 2 3.8 Lengths and tolerances The normal manufacturing lengths of the pipes and fittings, and their tolerances, are given in Clause 4. 3.9 Tolerances on angles The tolerances

45、 on the angles of the bends and branches are fixed at 2 throughout. SANS 6594:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 6594:2006(E) ISO 2006 All rights reserved 53.10 Masses and tolerances The negative tolerance with respect to

46、 the mass, if indicated in the manufacturers catalogue, shall be: 15 % for pipes; 15 % for fittings. Positive tolerances are not specified, but components whose mass is greater than indicated shall be accepted, provided they satisfy all other requirements of this International Standard. 3.11 Protect

47、ion Unless otherwise specified, drainage pipes and fittings shall be supplied coated internally and externally. The coatings shall dry rapidly, shall not be sticky, shall adhere well, shall not chip and shall be sufficiently resistant to temperature under normal conditions of use, transportation and

48、 storage of the products. The external coatings shall, in addition, be suitable for the application of finish coatings. 4 Dimensions 4.1 Pipe Symbol: Tolerance on L of 3 m: 20 mm, for all diameters. See Figure 3. Dimensions in metres Figure 3 SANS 6594:2008This s tandard may only be used and printed

49、 by approved subscription and freemailing clients of the SABS .ISO 6594:2006(E) 6 ISO 2006 All rights reserved4.2 Fittings 4.2.1 45 bend Symbol: Tolerance on a: 5 mm. See Table 4 and Figure 4. Table 4 45 bend a Nominal size DN mm 40 45 50 50 70a60 75a100 70 125 80 150 90 200 110 250 130 300 155 400 247 500 318 600 350 aThe range of nominal sizes and their classification differ slightly from one country to another. The use of DN 7