SAE AS 81714 26-2001 TERMINAL JUNCTION SYSTEM TERMINAL JUNCTION BLOCKS SECTIONAL MODULES ELECTRONIC FEEDBACK TYPE SIZE 20-2 SERIES I《FSC 5940 I系列 尺寸20-2的反馈式电子模块可组合终端连接块的终端连接系统》.pdf

《SAE AS 81714 26-2001 TERMINAL JUNCTION SYSTEM TERMINAL JUNCTION BLOCKS SECTIONAL MODULES ELECTRONIC FEEDBACK TYPE SIZE 20-2 SERIES I《FSC 5940 I系列 尺寸20-2的反馈式电子模块可组合终端连接块的终端连接系统》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 81714 26-2001 TERMINAL JUNCTION SYSTEM TERMINAL JUNCTION BLOCKS SECTIONAL MODULES ELECTRONIC FEEDBACK TYPE SIZE 20-2 SERIES I《FSC 5940 I系列 尺寸20-2的反馈式电子模块可组合终端连接块的终端连接系统》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, MODULES, ELECTRONIC, FEEDBACK TYPE, SIZE 20-2, SERIES I AS81714/26Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in an

2、y form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS:

3、 http:/www.sae.org ISSUED 2001-07REAFFIRMED 2012-01THIRD ANGLE PROJECTION CUSTODIAN: AE-8C2 FEDERAL SUPPLY CLASS 5940 AS81714/26SHEET 1 OF 4 SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report i

4、s entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE

5、invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS81714/26 RATIONALE AS81714/26 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICETHIS DOCUMENT HAS BEEN TAKEN DI

6、RECTLY FROM U.S. MILITARY SPECIFICATION MIL-T-81714/26B AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEASE OF THIS DOCUMENT IS INTENDED TO REPLACE MIL-T-81714/26B. ANY PART NUMBER

7、S ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED.THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARD

8、S. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUAL

9、IFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT.AEROSPACE STANDARD AS81714/26SHEET 2 OF 4 TERMINAL JUNCTION SYSTEM, T

10、ERMINAL JUNCTION BLOCKS, SECTIONAL, MODULES, ELECTRONIC, FEEDBACK TYPE, SIZE 20-2, SERIES I THE COMPLETE REQUIREMENTS FOR ACQUIRING THE BLOCKS DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SPECIFICATION MIL-T-81714.AEROSPACE STANDARD AS81714/26SHEET 3 OF 4 TERMINAL JUNCTION

11、 SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, MODULES, ELECTRONIC, FEEDBACK TYPE, SIZE 20-2, SERIES I TABLE I.FIGURE 1. BLOCKS WITH DIODES.TABLE II. DASH NUMBERS FOR FIGURE 1.REQUIREMENTS:1. MATERIALS:a. CURRENT CARRYING MEMBERS OF THE ELECTRONIC IN-LINE JUNCTION SHALL BE IN ACCORDANCE WITH THE IN-L

12、INE JUNCTION SPECIFICATION.AEROSPACE STANDARD AS81714/26SHEET 4 OF 4 TERMINAL JUNCTION SYSTEM, TERMINAL JUNCTION BLOCKS, SECTIONAL, MODULES, ELECTRONIC, FEEDBACK TYPE, SIZE 20-2, SERIES I NOTES:1. DIMENSIONS ARE IN INCHES.2. MIL-T-81714 REQUIREMENTS APPLY TO BASIC BLOCK ONLY. FOR RATING AND CHARACTE

13、RISTICS OF ELECTRONIC IN-LINE JUNCTION(S), CONSULT COMPONENT SPECIFICATION.3. THIS BLOCK IS DESIGNED FOR INSTALLATION IN MIL-T-81714/5 AND MIL-T-81714/16 RACKS WITH ITS INDEXING INDICATOR ADJACENT TO THE INDEXING RACK RAIL. THIS BLOCK CAN ALSO BE INSTALLED IN MIL-T-81714/29 BRACKETS.4. TOOLS FOR CON

14、TACT INSERTING/REMOVAL ARE M81969/14-02 OR M81969/8-06 AND SHALL BE ORDERED SEPARATELY.5. METRIC EQUIVALENTS (TO THE NEAREST .01 MM) ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED UPON 1 INCH = 25.4 MM.6. INTERNATIONAL INTEREST, SEE SPECIFICATION MIL-T-81714.7. THE PART NUMBER CONSISTS OF THE

15、LETTER M, SPECIFICATION SHEET NUMBER, BLOCK CLASS AND ELECTRONIC COMPONENT/CIRCUIT DASH NUMBER (SEE FIGURE 1).PART NUMBER EXAMPLE:M81714/26-001FEEDBACK TYPE ELECTRONIC BLOCK, CLASS D SIZE 20-2, WITH -001 CIRCUIT (FIVE JAN TX 1N5618).8. CLASSES A, B AND C COMPONENTS ARE INACTIVE FOR DESIGN. ONLY CLASS D COMPONENTS SHALL BE USED FOR DIRECT GOVERNMENT ACQUISITION.