SAE AS 5232B-2014 FITTING ADAPTER REDUCER PORT TO FLARELESS《非扩口端异径适配器配件》.pdf

上传人：吴艺期

文档编号：1024795

上传时间：2019-03-21

格式：PDF

页数：5

大小：62.94KB

《SAE AS 5232B-2014 FITTING ADAPTER REDUCER PORT TO FLARELESS《非扩口端异径适配器配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5232B-2014 FITTING ADAPTER REDUCER PORT TO FLARELESS《非扩口端异径适配器配件》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD FITTING, ADAPTER, REDUCER, PORT TO FLARELESS AS5232Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or oth

2、erwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-03REAFFIRMED 2004-07 REVISED 2014-08THIRD ANGLE

3、PROJECTION CUSTODIAN: G-3/G-3B REV.BFEDERAL SUPPLY CLASS 4730 AS5232SHEET 1 OF 5REV. BPROCUREMENT SPECIFICATION: AS18280 /4/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreportis entirelyvoluntary

4、, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittenco

5、mments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS5232BRATIONALE MATERIAL OPTION FOR 15-5PH CORROSION RESISTANT STEEL HAS BEEN ADDED. UPDATES. FIGURE 1 - FITTING, ADAPTER AEROSPACE STANDARD AS5232SHEET 2 OF

6、 5REV. BFITTING, ADAPTER, REDUCER, PORT TO FLARELESS TABLE 1 - DIMENSIONS BASIC NO. AS5232/15/SIZE CODE (NOMINAL TUBE SIZE) PORT #1(NOMINAL TUBE SIZE) PORT #2T THREAD PERAS8879CLASS 3B P THREAD PERAS8879CLASS 3A A B C 0302 .188 .125 .3750-24 UNJF .3125-24 UNJF 1.125 .406 .516 0402 .250 .125 .4375-20

7、 UNJF .3125-24 UNJF 1.234 .438 .610 0403 .250 .188 .4375-20 UNJF .3750-24 UNJF 1.250 .438 .610 0504 .312 .250 .5000-20 UNJF .4375-20 UNJF 1.281 .438 .610 0604 .375 .250 .5625-18 UNJF .4375-20 UNJF 1.313 .469 .610 0605 .375 .312 .5625-18 UNJF .5000-20 UNJF 1.281 .469 .610 0804 .500 .250 .7500-16 UNJF

8、 .4375-20 UNJF 1.484 .562 .734 0805 .500 .312 .7500-16 UNJF .5000-20 UNJF 1.453 .562 .734 0806 .500 .375 .7500-16 UNJF .5625-18 UNJF 1.469 .562 .734 1004 .625 .250 .8750-14 UNJF .4375-20 UNJF 1.578 .625 .797 1005 .625 .312 .8750-14 UNJF .5000-20 UNJF 1.563 .625 .797 1006 .625 .375 .8750-14 UNJF .562

9、5-18 UNJF 1.563 .625 .797 1008 .625 .500 .8750-14 UNJF .7500-16 UNJF 1.656 .625 .797 1206 .750 .375 1.0625-12 UNJ .5625-18 UNJF 1.734 .688 .922 1208 .750 .500 1.0625-12 UNJ .7500-16 UNJF 1.828 .688 .922 TABLE 1A - DIMENSIONS AND WEIGHTS BASIC NO. AS5232/15/SIZE CODE D.010 H LB/EAAPPROX.REF ALLB/EAAP

10、PROX.REF STEELLB/EAAPPROX. REF TI0302 .605 .615- .628 .0248 .0711 .0392 0402 .668 .678- .691 .0324 .0929 .0513 0403 .668 .678- .691 .0323 .0928 .0512 0504 .730 .740- .753 .0373 .107 .0590 0604 .792 .802- .815 .0438 .126 .0693 0605 .792 .802- .815 .0307 .0881 .0486 0804 .980 .990-1.003 .0707 .203 .11

11、2 0805 .980 .990-1.003 .0687 .197 .109 0806 .980 .990-1.003 .0701 .201 .111 1004 1.103 1.113-1.128 .0928 .266 .147 1005 1.103 1.113-1.128 .0918 .264 .145 1006 1.103 1.113-1.128 .0902 .259 .143 1008 1.103 1.113-1.128 .0958 .275 .152 1206 1.353 1.363-1.380 .153 .438 .242 1208 1.353 1.363-1.380 .158 .4

12、54 .250 AEROSPACE STANDARD AS5232SHEET 3 OF 5REV. BFITTING, ADAPTER, REDUCER, PORT TO FLARELESS TABLE 1B - DIMENSIONS BASIC NO. AS5232/15/SIZE CODE (NOMINAL TUBE SIZE) PORT #1(NOMINAL TUBE SIZE) PORT #2T THREAD PERAS8879CLASS 3B P THREAD PERAS8879CLASS 3A A B C 1210 .750 .625 1.0625-12 UNJ .8750-14

13、UNJF 1.891 .688 .922 1606 1.000 .375 1.3125-12 UNJ .5625-18 UNJF 1.844 .688 .954 1608 1.000 .500 1.3125-12 UNJ .7500-16 UNJF 1.938 .688 .954 1610 1.000 .625 1.3125-12 UNJ .8750-14 UNJF 1.984 .688 .954 1612 1.000 .750 1.3125-12 UNJ 1.0625-12 UNJ 2.031 .688 .954 2008 1.250 .500 1.6250-12 UNJ .7500-16

14、UNJF 2.078 .688 1.000 2010 1.250 .625 1.6250-12 UNJ .8750-14 UNJF 2.125 .688 1.000 2012 1.250 .750 1.6250-12 UNJ 1.0625-12 UNJ 2.156 .688 1.000 2016 1.250 1.000 1.6250-12 UNJ 1.3125-12 UNJ 2.078 .688 1.000 TABLE 1C - DIMENSIONS AND WEIGHTS BASIC NO. AS5232/15/SIZE CODE D.010 H LB/EAAPPROX.REF ALLB/E

15、AAPPROX.REF STEELLB/EAAPPROX. REFTI1210 1.353 1.353-1.380 .163 .469 .259 1606 1.603 1.613-1.630 .221 .635 .350 1608 1.603 1.613-1.630 .226 .649 .358 1610 1.603 1.613-1.630 .219 .630 .347 1612 1.603 1.613-1.630 .228 .654 .361 2008 1.853 1.863-1.880 .304 .873 .481 2010 1.853 1.863-1.880 .303 .871 .480

16、 2012 1.853 1.863-1.880 .297 .851 .470 2016 1.853 1.863-1.880 .276 .793 .438 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. DASH AS CODE LETTER - TYPE 4130 CARBON STEE

17、L BAR PER AMS6370. /2/ b. CODE LETTER D - TYPE 2024-T6 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6 OR AMS4112 OR TYPE 2024-T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6. /2/ c. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL BAR PER AMS5639. d. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL BAR PER AM

18、S5648. e. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL BAR PER AMS5645. f. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS4928. g. CODE LETTER V - TYPE 15-5PH CORROSION RESISTANT STEEL BAR PER AMS5659. /2/ h. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9 OR TYPE 70

19、75-T7351 ALUMINUM ALLOY BAR PER AMS4124. /2/ AEROSPACE STANDARD AS5232SHEET 4 OF 5REV. BFITTING, ADAPTER, REDUCER, PORT TO FLARELESS /2/ HEAT TREATMENT: a. DASH AS MATERIAL CODE LETTER - SEE HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTERS D AND W - SEE ELECTRICAL CONDUCT

20、IVITY AND HARDNESS REQUIREMENT PER PROCUREMENT SPECIFICATION. c. MATERIAL CODE LETTER V - HEAT TREAT TO CONDITION H-1075 PER AMS2759/3. d. OTHER MATERIAL CODE LETTERS - NONE. 3. FINISH: a. DASH AS CODE LETTER - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2 AND COAT WITH A LIGHT FILM OF OIL PER PR

21、OCUREMENT SPECIFICATION. b. CODE LETTER D - ANODIZE PER MIL-A-8625, TYPE II, CLASS 2, DYE GREEN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. c. CODE LETTER J, K, AND R - PASSIVATE PER AMS2700 PER PROCUREMENT SPECIFICATION. d. CODE LETTER T - ANODIZE PER AMS2488 OR FLUORIDE PHOSPHATE CONVERSION COAT P

22、ER AMS2486 WITH COLOR PER PROCUREMENT SPECIFICATION. e. MATERIAL CODE LETTER V: (1) NO SUFFIX FINISH CODE LETTER: PASSIVATE PER AMS2700, TYPE 2 OR 8. (2) SUFFIX FINISH CODE LETTER “P”: CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2. f. MATERIAL CODE LETTER W - ANODIZE PER MIL-A-8625, TYPE II, CLAS

23、S 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. /4/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LI

24、ST PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/www.eAuditN FOR CURRENT QPL ONLINE. NOTE: PRI-QPL LIMITATION - WITH REVISION A OF THIS STANDARD THE PROCUREMENT SPECIFICATION HAS BEEN CHANGED FROM AS4444 FOR 5000 PSI TO AS18280 FOR 3000 PSI. USERS OF THIS FITTING FOR 5000 PSI APPLICATIONS PER AS4444

25、MUST PROVIDE THEIR OWN QPL-CONTROL. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” AND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR

26、 TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. THIS STANDARD IS THE FUNCTIONAL EQUIVALENT OF MS21915 AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. b. CLEANING OF ALUMINUM AL

27、LOY AND CORROSION RESISTANT STEEL FITTINGS IN ACCORDANCE WITH ARP1176 (CODE LETTER “A”) IS REQUIRED FOR OXYGEN SYSTEMS TO AVOID FIRE DUE TO PARTICLES OR OTHER CONTAMINANTS. AEROSPACE STANDARD AS5232SHEET 5 OF 5REV. BFITTING, ADAPTER, REDUCER, PORT TO FLARELESS /7/ THE INTERNAL DIAMETER SHALL END IN

28、A CONICAL END OF 110 DEGREES MINIMUM INCLUDED ANGLE. /8/ THE HEX CORNERS MAY BE ROUNDED PER ARP1942. /9/ SUFFIX LETTER A: CODE A ALUMINUM AND CORROSION RESISTANT STEEL PARTS USED IN OXYGEN SYSTEMS SHALL BE CLEANED AND PACKAGED IN ACCORDANCE WITH ARP1176 CATEGORY 2 FOR ALUMINUM AND CATEGORY 1C FOR CO

29、RROSION RESISTANT STEEL. 10. INTERPRETATION OF DRAWING PER AS4296. 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. SURFACES OF HEX FLATS MAY BE 250 MICROINCHES Ra. 12. BREAK EDGES .003 TO .015 UNLESS

30、OTHERWISE SPECIFIED. 13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 14. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 DEGREES 30 MINUTES. /15/ EXAMPLE OF PART NUMBER: AS5232 V 08 06 A BASIC PART NUMBER CODE LETTER FOR OXYGEN SYSTEMS /

31、9/, OR “P” FOR CADMIUM PLATED 15-5PH MATERIAL /3.e.(2)/. OMIT IF NOT REQUIRED. MATERIAL CODE LETTER /1/ SIZE CODE, TUBE SIZE OF PORT #2 IN .062 INCREMENTS SIZE CODE, TUBE SIZE OF PORT #1 IN .062 INCREMENTS 16. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING

32、 AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.

下载提示：本站仅提供存储空间/不修改/不编辑