SAE AS 33702B-2015 INSERT ARRANGEMENTS ELECTRIC CONNECTOR SHELL SIZE 27 (FOR AS81703 CONNECTORS).pdf

《SAE AS 33702B-2015 INSERT ARRANGEMENTS ELECTRIC CONNECTOR SHELL SIZE 27 (FOR AS81703 CONNECTORS).pdf》由会员分享，可在线阅读，更多相关《SAE AS 33702B-2015 INSERT ARRANGEMENTS ELECTRIC CONNECTOR SHELL SIZE 27 (FOR AS81703 CONNECTORS).pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD (R) INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 27 (FOR AS81703 CONNECTORS) AS33702Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, me

2、chanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2002-02REVISE

3、D2015-12 THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.B FEDERAL SUPPLY CLASS 5935 AS33702 SHEET 1 OF 7 REV. B PROCUREMENT SPECIFICATION: NONE SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of thisreport isent

4、irelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,orcancelled. SAEinvites yourwritten

5、comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS33702B RATIONALE REVISION IS REQUIRED TO REMOVE IMAGES AND REPLACE WITH WORD TEXT/TABLES, TO COMBINE INSERT PATTERN INFORMATION INTO ONE TABLE, TO DELETE

6、CANCELLED CONNECTOR SPECIFICATION REFERENCES, TO REMOVE GOVERNMENT JARGON/CONVERSION INFORMATION, TO REMOVE THE PROCUREMENT SPECIFICATION, TO ADD THE APPLICABLE CONNECTOR SPECIFICATION TO THE DOCUMENT TITLE, TO CHANGE ALL DIMENSIONS TO FOUR DECIMAL PLACES, AND TO UPDATE DOCUMENT TO MOST CURRENT SAE

7、GUIDELINES. CONTACT SIZE: 16 NUMBER OF CONTACTS: 14 SERVICE RATING: I FIGURE 1 - INSERT ARRANGEMENT 27-2 AEROSPACE STANDARD AS33702 SHEET 2 OF 7 REV. B (R) INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 27 (FOR AS81703 CONNECTORS) CONTACT SIZE: 20/16 NUMBER OF CONTACTS: 14 SIZE 20/2 SIZE 16 SER

8、VICE RATING: I FIGURE 2 - INSERT ARRANGEMENT 27-3 CONTACT SIZE: 20 NUMBER OF CONTACTS: 10 SERVICE RATING: I FIGURE 3 - INSERT ARRANGEMENT 27-4 AEROSPACE STANDARD AS33702 SHEET 3 OF 7 REV. B (R) INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 27 (FOR AS81703 CONNECTORS) CONTACT SIZE: 16 NUMBER OF

9、 CONTACTS: 19 SERVICE RATING: I FIGURE 4 - INSERT ARRANGEMENT 27-5 CONTACT SIZE: 16/12 NUMBER OF CONTACTS: 6 SIZE 16/4 SIZE 12 SERVICE RATING: I FIGURE 5 - INSERT ARRANGEMENT 27-8 AEROSPACE STANDARD AS33702 SHEET 4 OF 7 REV. B (R) INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 27 (FOR AS81703 C

10、ONNECTORS) CONTACT SIZE: 20 NUMBER OF CONTACTS: 12 SERVICE RATING: II (CONTACTS 1 & 2) SERVICE RATING I (ALL OTHERS) FIGURE 6 - INSERT ARRANGEMENT 27-11 CONTACT SIZE: 20 NUMBER OF CONTACTS: 22 SERVICE RATING: I FIGURE 7 - INSERT ARRANGEMENT 27-22 AEROSPACE STANDARD AS33702 SHEET 5 OF 7 REV. B (R) IN

11、SERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 27 (FOR AS81703 CONNECTORS) CONTACT SIZE: 20 NUMBER OF CONTACTS: 24 SERVICE RATING: I FIGURE 8 - INSERT ARRANGEMENT 27-24 CONTACT SIZE: 20 NUMBER OF CONTACTS: 27 SERVICE RATING: I FIGURE 9 - INSERT ARRANGEMENT 27-50 AEROSPACE STANDARD AS33702 SHEET 6

12、 OF 7 REV. B (R) INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 27 (FOR AS81703 CONNECTORS) FIGURE 10 - INSERT POSITION TABLE 1 - INSERT POSITION DETAILS (SEE FIGURE 10) INSERT ARRANGEMENT INSERT POSITION “A” DEGREESN W X Y Z B C 27-2 0 25 50 75 (B) 150 225 27-3 0 25 50 75 (B) 150 22527-4 0 25

13、50 75 (B) 150 225 27-5 0 (B) (B) 75 (B) 150 22527-8 0 25 50 75 (B) 150 225 27-11 0 25 50 75 (B) 150 22527-22 0 25 50 75 N/A 150 225 27-24 0 25 50 75 N/A 150 22527-50 (C) 0 25 50 75 N/A 150 225 (A) TO BE WITHIN .005 INCHES OF THE REQUIRED POSITION (.006 INCHES FOR INSERT 27-8 AND 27-11) (B) THESE INS

14、ERT POSITIONS ARE NOT TO BE PROVIDED (C) INSERT ARRANGEMENT 27-50 SUPERSEDES AND IS INTERCHANGEABLE WITH INSERT ARRANGEMENT -19 NOTES: 1. INDICATES “MASTER KEY OR KEYWAY OF SHELL”. 2. INDICATING TERMINUS OF “INDEXING RADIUS OF INSERT” SHALL BE PERMANENTLY MARKED ON THE INSERT FOR ALL INSERT POSITION

15、S OTHER THAN “N” OR “NORMAL”. 3. WHEN VIEWED FROM THE ENGAGING END, IN “N” POSITION THE INDEXING RADIUS COINCIDES WITH THE CENTERLINE OF THE MASTER KEYWAY OF THE SHELL. 4. WHEN VIEWED FROM THE ENGAGING END, IN OTHER THAN “N” POSITION THE PIN INSERT IS ROTATED “A” DEGREES CLOCKWISE RELATIVE TO THE CE

16、NTERLINE OF THE MASTER KEY OR KEYWAY OF THE SHELL AS INDICATED. 5. WHEN VIEWED FROM THE ENGAGING END, IN OTHER THAN “N” POSITION THE SOCKET INSERT IS ROTATED “A” DEGREES COUNTER CLOCKWISE RELATIVE TO THE CENTERLINE OF THE MASTER KEY OR KEYWAY OF THE SHELL. AEROSPACE STANDARD AS33702 SHEET 7 OF 7 REV

17、. B (R) INSERT ARRANGEMENTS, ELECTRIC CONNECTOR, SHELL SIZE 27 (FOR AS81703 CONNECTORS) 6. DIMENSIONS AND MARKINGS SHOWN IN FIGURES 1 THROUGH 10 ARE FOR FRONT FACE OF PIN INSERT (SOCKET INSERT OPPOSITE). UNLESS OTHERWISE INDICATED, DIMENSIONS ARE SYMMETRICAL ABOUT CENTERLINE. 7. DIMENSIONS ARE IN IN

18、CHES. ANGLES ARE IN DEGREES. TOLERANCES: DECIMALS .005. 8. THIS IS A DESIGN STANDARD AND IS NOT TO BE USED AS A PART NUMBER. 9. FOR DESIGN FEATURE PURPOSES THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN. 10. APPLICABLE CONNECTORS: RECEPTACLES (REF.) PLUGS (REF.) AS31301

19、AS31371AS31321 S31381AS31341 AS31471AS31391 S31481 AS31401 AS34461AS31431 S34671AS31441 AS34451AS31491 AS34241 AS34641 AS34661 SPECIFICATION NOTES: 1. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT E

20、DITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.