SAE AMS-QQ-A-225 5-1997 Aluminum Alloy 2017 Bar Rod and Wire Rolled Drawn or Cold Finished (UNS A92017)《轧制 拉制或冷加工的2017铝合金棒材 杆材 线材和型材 UNS A92017》.pdf

《SAE AMS-QQ-A-225 5-1997 Aluminum Alloy 2017 Bar Rod and Wire Rolled Drawn or Cold Finished (UNS A92017)《轧制 拉制或冷加工的2017铝合金棒材 杆材 线材和型材 UNS A92017》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS-QQ-A-225 5-1997 Aluminum Alloy 2017 Bar Rod and Wire Rolled Drawn or Cold Finished (UNS A92017)《轧制 拉制或冷加工的2017铝合金棒材 杆材 线材和型材 UNS A92017》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Aluminum Alloy, 2017, Bar, Rod, and WireRolled, Drawn, or Cold FinishedA92017RATIONALEThis document has been reaffirmed to comply with the SAE 5-year Review policy.NOTICEThis document has been taken directly from Federal Specification QQ-A-225/5E, Amendment 2, and contains only minor editorial and f

2、ormat changes required to bring it into conformance with the publishing requirements of SAE technical standards.The original Federal Specification was adopted as an SAE standard under the provisions of the SAE Technical Standards Board (TSB) Rules and Regulations (TSB 001) pertaining to accelerated

3、adoption of government specifications and standards. TSB rules provide for (a) the publication of portions of unrevised government specifications and standards without consensus voting at the SAE Committee level, (b) the use of the existing government specification or standard format, and (c) the ex

4、clusion of any qualified product list (QPL) sections.The complete requirements for procuring 2017 aluminum alloy bar, rod, and wire, rolled, drawn, or cold finished shall consist of this specification and the latest issue of AMS-QQ-A-225.AEROSPACE MATERIAL SPECIFICATIONAMS-QQ-A-225/5IssuedReaffirmed

5、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr

6、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication may

7、 be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA

8、) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMSQQA225/5 1997-072010-05AMS-QQ-A-225/5 SAE AMS-QQ-A-225/5- 2 -1. SCOPE AND CLASSIFICATION:1.1

9、 Scope: This specification covers the specific requirements for 2017 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing.1.2 Classification: 1.2.1 Tempers: Bar, rod, and wire are of the following tempers, as specified (See 6.2): O, T4, T42, or T451 temper. Definitions of

10、these tempers are specified in AMS-QQ-A-225.2. APPLICABLE DOCUMENTS: See AMS-QQ-A-225.3. REQUIREMENTS: 3.1 Chemical Composition: The chemical composition shall conform to the requirements specified in Table I.Chemical Composition 1/ElementPercentMinimum MaximumCopper 3.5 4.5Manganese 0.40 1.0Magnesi

11、um 0.40 0.8Silicon 0.20 0.8Iron -0.7Zinc 25Chromium -0.10Titanium 5Other Elements, each -0.0Other Elements, total 15Aluminum Remainder1/ Analysis shall routinely be made only for the elements specifically mentioned in Table I. If, however, the presence of other elements is indicated or suspected in

12、the course of routine analysis, further analysis shall be made to determine conformance to the limits specified for other elements.AMS-QQ-A-225/5 SAE AMS-QQ-A-225/5- 3 -3.2 Mechanical Properties: 3.2.1 Mechanical Properties of Material as Supplied: The mechanical properties in the direction of worki

13、ng shall conform to the requirements of Table II for the temper specified.3.2.2 Mechanical Properties After Heat Treatment: In addition to conforming to requirements of 3.2.1, material supplied in the tempers identified in the following paragraphs shall, after having been processed to tempers also i

14、dentified therein, have properties conforming to those specified in Table II, as applicable.3.2.2.1 Material in the Annealed (O) Temper: Material supplied in the O temper, without subsequent cold work or forming operations, shall, after solution heat treatment and natural aging, develop the properti

15、es specified for the T42 temper.3.2.2.2 Material in the T4 and T451 Tempers: Material in the T4 and T451 tempers shall, without subsequent cold work or forming operations, be capable of being re-solution heat treated and naturally aged to the properties specified for the T42 tempers. Such capability

16、 shall be demonstrated when specified (See 6.2).TABLE I. Mechanical Properties (See 6.4)TemperDiameterorThicknessInchesTensileStrengthminimumksiYield Strengthat 0.2 percentOffset orat ExtensionIndicated 5/Elongationin 2 inchesor 4 timesdiameter 5/minimumpercentminimum,ksiextensionunder load,inch/inc

17、hO Up to 8.000,inclusive35.0 2/ - - 16T4 andT42 3/Up to 8.000,inclusive 4/55.0 32.0 0.0050 12T451 1/ 0.500 to 8.000,inclusive 4/55.0 32.0 0.0050 121/ T451 temper is available only in bar, rod and shapes.2/ Maximum.3/ Material in the T42 temper is not available from the material producers.4/ For bar,

18、 maximum cross-sectional area is 50 square inches.5/ See AMS-QQ-A-225 for yield strength and elongation requirement exceptions.AMS-QQ-A-225/5 SAE AMS-QQ-A-225/5- 4 -3.2.3 Bending: When specified (See 6.2), the material shall withstand without cracking, the bend test specified in AMS-QQ-A-225. The va

19、lues for bend factor N are given in Table III.3.3 Finish: Unless otherwise specified in the contract or order (see 6.2), rod up to and including 3 inches in diameter, and bar up to and including 2 inches thick (with maximum width for rectangles of 4 inches) shall be processed to size by cold finishi

20、ng.4. QUALITY ASSURANCE PROVISIONS: See AMS-QQ-A-225 and the following:4.1 Heat Treatment; Aging Period Before Mechanical Property Testing: Specimens in the T4, T42, and T451 tempers will not be required to be tested within 4 days after completion of heat treatment. If, within this period, the manuf

21、acturer elects to test samples which fail to meet the requirements, he can discard these initial test results and test additional specimens selected after four days of aging. These specimens shall be selected from the same locations in the lot from which the prior specimens were removed.4.2 Mechanic

22、al Test After Heat Treatment: 4.2.1 Number of Tests After Heat Treatment: From material in the annealed (O) temper, an additional number of specimens equal to those required by AMS-QQ-A-225 shall be taken and tested after solution heat treatment to determine compliance with 3.2.2.5. PREPARATION FOR

23、DELIVERY: See AMS-QQ-A-225.TABLE II. Bend Test Factor “N“TemperDiameter, Thickness orLeast Distance BetweenParallel Faces, Inches NT4 Up to 0.124, incl 30.125 to 8.000, incl 6T451 0.500 to 8.000, incl 6AMS-QQ-A-225/5 SAE AMS-QQ-A-225/5- 5 -6. NOTES:6.1 Intended Use: This alloy is intended for use in

24、 machining applications and where good strength is required. The T451 temper is intended primarily to provide material with low residual stresses and consequent minimum distortion during machining.6.2 Ordering Data: Purchaser should select the preferred options permitted herein and include the follo

25、wing information in procurement documents:Title, number, and date of this specificationForm, quantity, and temper required (See 1.2.1)Dimensions requiredMechanical properties and dimensional tolerance requirements for sizes not specifically coveredWhether bend tests are required (See 3.2.3)Requireme

26、nts for demonstrations of heat treatment capability to develop properties in the tempers specified (See 3.2.2.2).Finish requirements for sizes not specifically covered (See 3.3)Whether there are special end use requirementsFor military agencies: selection of applicable levels of preservation, packag

27、ing, and packing required. Also specify marking requirements (See AMS-QQ-A-225)For civil agencies: specify packing level, level A, or commercial. Also specify marking requirements (See AMS-QQ-A-225)6.3 Product produced and marked to the requirements of AMS-QQ-A-225/5 also meets the requirements of Q

28、Q-A-225/5E, Amendment 2. Product produced and marked to the requirements of QQ-A-225/5E, Amendment 2, also meets the requirements of AMS-QQ-A-225/5.6.4 Properties listed in 3.2.1 are exactly the same as QQ-A-225/5, Revision E, Amendment 2. These properties have not been substantiated in accordance with the AMS Manual for Preparation of Aerospace Specifications.6.5 Changes authorized by QQ-A-225/5E, Amendment 2, have been incorporated into Table II, 3.2.2, 3.2.2.1, 3.2.2.2, and 6.2.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “D“