NEMA C136 6-2004 For Roadway and Area Lighting Equipment C Metal Heads and Reflector Assemblies Mechanical and Optical Interchangeability《道路和区域照明设备 路灯的金属头和反光器组件 机械互换性与光学互换性[代替 A.pdf

《NEMA C136 6-2004 For Roadway and Area Lighting Equipment C Metal Heads and Reflector Assemblies Mechanical and Optical Interchangeability《道路和区域照明设备 路灯的金属头和反光器组件 机械互换性与光学互换性[代替 A.pdf》由会员分享，可在线阅读，更多相关《NEMA C136 6-2004 For Roadway and Area Lighting Equipment C Metal Heads and Reflector Assemblies Mechanical and Optical Interchangeability《道路和区域照明设备 路灯的金属头和反光器组件 机械互换性与光学互换性[代替 A.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI C136.6-2004 (R2012) American National Standard For Roadway and Area Lighting Equipment Metal Heads and Reflector Assemblies Mechanical and Optical Interchangeability Copyright 2012 by National Electrical Manufacturers Association ANSI C136.6-2004 (R2012) American National Standard For Roadway

2、and Area Lighting Equipment Metal Heads and Reflector Assemblies Mechanical and Optical Interchangeability Secretariat: National Electrical Manufacturers Association Approved July 14, 2012 Reaffirmed August 27 2012 American National Standards Institute, Inc. C136.6-2004 (R2012) Page ii Copyright 201

3、2 by National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that the

4、re is unanimous agreement among every person participating in the development of this document. ANSI standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers

5、 and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or complet

6、eness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly r

7、esulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, express or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document wi

8、ll fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render profession

9、al or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in de

10、termining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no powe

11、r, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health or safetyrelated information in t

12、his document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. C136.6-2004 (R2012) Page iii Copyright 2012 by National Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verif

13、ication by ANSI. ANSI states that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly and materi

14、ally affected interests. Substantial agreement means significantly more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and a concerted effort be made toward their resolution. The use of American National Standards is completely

15、voluntary; their existence does not in any respect preclude anyone, whether they have approved the standards or not, from: manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. The American National Standards Institute does not develop sta

16、ndards, and will under no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute. Requests for interpretations s

17、hould be addressed to the secretariat or sponsor whose name appears on the title page of this standard. Caution Notice: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken periodically to re

18、affirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute. Published by National Electrical Manufacturers Association 1300 North 17th Street, Rosslyn, VA 22209

19、g164 Copyright 2012 by National Electrical Manufacturers Association All rights reserved including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American Copyr

20、ight Conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, and without the prior written permission of the publisher. Printed in the United States of America. C136.6-2004 (R2012) Page iv Copyright 2012 by National Electrical Manufactu

21、rers Association C136.6-2004 (R2012) Page v Copyright 2012 by National Electrical Manufacturers Association TABLE OF CONTENTS 1 SCOPE 1 1.1 Dimensional Features for Interchangeability . 1 1.2 Slipfitter Mounted Heads . 1 1.3 Reflector Assembly . 1 2 NORMATIVE REFERENCES . 1 3 GENERAL . 1 4 METAL HEA

22、D ASSEMBLY 3 5 REFLECTOR ASSEMBLY . 3 6 VOLTAGE CLASSIFICATION 4 7 TESTS . 4 8 MATERIALS AND PROTECTIVE COATINGS 4 C136.6-2004 (R2012) Page 1 Copyright 2012 by National Electrical Manufacturers Association 1 SCOPE 1.1 Dimensional Features for Interchangeability This standard covers dimensional featu

23、res of luminaires with metal heads that permit mechanical and optical interchangeability of both head and reflector assemblies. 1.2 Slipfitter Mounted Heads The features covered in this standard apply to metal heads that are slipfitter mounted. 1.3 Reflector Assembly The reflector assembly is of the

24、 latched collar type and may be part of an open or enclosed optical assembly. 2 NORMATIVE REFERENCES This standard incorporates by undated reference provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed below.

25、For undated references, the latest edition of the publication referred to applies (including amendments). ANSI C136.2-1996, American National Standard for Roadway and Area Lighting EquipmentLuminaires Voltage Classification ANSI C136.3-1995, American National Standard for Roadway and Area Lighting E

26、quipmentLuminaire Attachments ANSI C136.4-1995, American National Standard for Roadway and Area Lighting EquipmentSeries Sockets and Series-socket Receptacles ANSI C136.9-1990, American National Standard for Roadway and Area Lighting EquipmentSocket Support Assemblies for Metal HeadsMechanical Inter

27、changeability ANSI C136.10-1996, American National Standard for Roadway and Area Lighting EquipmentLocking-type Photocontrol Devices and Mating ReceptaclePhysical and Electrical Interchangeability and Testing ANSI C136.11-1995, American National Standard for Roadway and Area Lighting EquipmentMultip

28、le Sockets 3 GENERAL Dimensional features of the metal head and the mounting and latching dimensions of metal head and reflector assemblies shall be in accordance with Figures 1a, 1b, and 1c. C136.6-2004 (R2012) Page 2 Copyright 2012 by National Electrical Manufacturers Association FIGURES 1A, 1B, A

29、ND 1C DIMENSIONS FOR METAL HEAD AND REFLECTOR ASSEMBLIES The socket assembly in the metal head shall be positioned with respect to the reflector seat to properly locate a recommended lamp light center for use with Class A or Class B reflectors in accordance with Figure 2.AA0.25 in B(6.33 mm)Figure 1

30、a Head and reflector orientation detail2.38 mm BX(0.093 in)25.40 mm Max(1.0 in)3.97 mm B(0.156 in)6.35 mm CX dia.(0.25 in)Section A-ARing or loopfor attachingservicing chain.Opening may bein any plane.85.725 mm Min(3.375 in)55.55 mm A(2.187 in)55.55 mm A(2.187 in)#10 Screw131.75 mm Min(5.19 in)Head

31、of washer or fastener not to exceed these limits:9.525 mm (0.375 in) Min12.70 mm (0.50 in) Max9.525 mm (0.375 in) MinInsertion depthLatch lugDimensions in blocks shallapply when receptaclemounting seat is specified.20.637 mm Min(0.812 in)144.45 mm (5.69 in) Min146.05 mm (5.75 in) Min146.05 mm BX dia

32、. (opening)(5.75 in)158.75 mm B dia. (refl. seat)(6.25 in)96.84 mm B(3.81 in)96.84 mm B(3.81 in)89.69 mm(3.53 in)89.69 mm(3.53 in)Latch seat3.18 mm C(0.12 in)29.98 mm A(1.6 in)136.53 mm D(5.38 in)Receptaclemounting seatReflectorseat3.18 mm C(0.12 in)Figure 1b Head detail. Centerline sectionThis dime

33、nsion to be19.05 mm C (0.75 in)for enclosed opticalassembly. Up to19.05 mm (0.75 in) foropen optical assembly.Head must accommodatethese dimensions.142.875 mm C Dia.(5.625 in)155.575 mm C Dia (Head seat)(6.125 in)4.75 mm Min(0.19 in)LatchNote latches in releasedposition shall freely clearlatch lugs.

34、Figure 1c Partial reflector detail showing fit dimensionsA = 0.396 mm (0.0156 in) D = 3.175 mm (0.125 in) Allowable variationsB = 0.793 mm (0.0312 in) X = 0.00 Single letter indicates same, (A = 0.396 mm 0.0156 in)C = 1.587 mm (0.0625 in) Two letters indicates first, +, second (AX = +0.396 mm 0.0156

35、 in),-0.00C136.6-2004 (R2012) Page 3 Copyright 2012 by National Electrical Manufacturers Association FIGURE 2 POSITION OF SOCKET ASSEMBLY 4 METAL HEAD ASSEMBLY 4.1 The metal head shall include one or more of the following: g120 A multiple socket in accordance with ANSI C136.9 and ANSI C136.11. g120

36、A series socket and receptacle in accordance with ANSI C136.4 g120 A provision for attaching the luminaire onto a luminaire support in accordance with ANSI C136.3 g120 A mating receptacle (for multiple-circuit use with a light-sensitive control device) in accordance with ANSI C136.10 and complete co

37、nnection wiring of the lamp socket to the control receptacle with supply points established at terminals within the metal head. 4.2 Latch lugs and their attachment to the metal head shall be capable of maintaining a total lift of 18.144 kg (40 lb) plus the weight of the optical assembly. 4.3 If spec

38、ified by the user, the metal head shall: g120 Have a servicing chain attaching device rigidly secured to the outside of the assembly not more than 25.4 mm (1.0 in.) above the reflector seat, and g120 Be capable of supporting a static load of 27.216 kg (60 lb). 5 REFLECTOR ASSEMBLY Reflector assembli

39、es shall include latches that, in the secured position, will hold the reflector firmly against the reflector seat of the metal head without failure or deformation of the reflector under the following load conditions: Head seat on reflectorLight center of reflector assembly“H” 3.175 mm (0.125 in)Clas

40、s A reflector: Dimension “H” = 158.75 mm (6.25 in)Class B reflector: Dimension “H” = 117.475 mm (4.625 in)Detail for opticalinterchangeability ofreflectorsC136.6-2004 (R2012) Page 4 Copyright 2012 by National Electrical Manufacturers Association g120 For open optical assemblies, 4.536 kg (10 lb) plu

41、s the weight of the optical assembly g120 For enclosed optical assemblies, 18.144 kg (40 lb) plus the weight of the optical assembly Reflector assemblies having non-hinged enclosed optical assemblies shall include a servicing chain with a safety catch at the end. This chain, together with catches, s

42、hall: g120 Have a minimum length of 228.6 mm (9 in.), and g120 Be capable of supporting a static load of 18.144 kg (40 lb) plus the weight of the optical assembly. 6 VOLTAGE CLASSIFICATION The voltage classification of the metal head shall be in accordance with ANSI C136.2. 7 TESTS Tests for optical

43、 interchangeability of reflectors shall be made with the lamp light center positioned in accordance with Figure 2. Note: In reference to Figure 2, reflectors are defined as follows: g120 Class A reflectordesigned for use with a lamp light center 158.75 mm (6.25 in.) below the reflector seat. g120 Cl

44、ass B reflectordesigned for use with a lamp light center 117.475 mm (4.625 in.) below the reflector seat. 8 MATERIALS AND PROTECTIVE COATINGS Materials and protective coatings used for metal head and reflector assemblies, including latches and the servicing chains, shall individually and as a system be resistant to atmospheric conditions, including the corrosive and erosive action of conditions of service encountered in industrial and seaboard areas.