NEMA C136 53-2017 Roadway and Area Lighting Equipment - Enclosed Pendant Mounted Luminaires.pdf

《NEMA C136 53-2017 Roadway and Area Lighting Equipment - Enclosed Pendant Mounted Luminaires.pdf》由会员分享，可在线阅读，更多相关《NEMA C136 53-2017 Roadway and Area Lighting Equipment - Enclosed Pendant Mounted Luminaires.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C136.53-2017Roadway and Area Lighting Equipment Enclosed Pendant Mounted LuminairesANSI C136.53-2017 American National Standard for Roadway and Area Lighting Equipment Enclosed Pendant Mounted Luminaires Secretariat: Nationa

2、l Electrical Manufacturers Association Approved: December 21, 2017 American National Standards Institute, Inc. 2017 National Electrical Manufacturers Association NOTICE AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the deve

3、lopment and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. ANSI standards and guideline publications, of which the document contained herein is one, are

4、 developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process to promote fairness in the development of consensus,

5、 it does not write the document, and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or other damag

6、es of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness

7、 of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue of this

8、 standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should

9、 rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic covered by this publication may be available from other sources, which

10、the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety or hea

11、lth purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the statement. ANSI C136.53-2017 Page i 2017 National Electrical Manufactur

12、ers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. An American

13、 National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of Standards Review, substantial agreement has been reached by directly, and materially affected interests. Substantial agreement me

14、ans much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered and that a concerted effort be made toward their resolution. The existence of an American National Standard does not in any respect preclude anyone, whether s/he has ap

15、proved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a guide to aid the manufacturer, the consumer, and the general public. The American National Standards Institute, Inc., does not devel

16、op standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the name of the American National Standards Institute, Inc. Requests for interpreta

17、tions should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute, Inc. require that action be taken periodically to reaff

18、irm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute, Inc. Published by National Electrical Manufacturers Association 1300 North 17thStreet, Rosslyn, VA 22209

19、 2017 National Electrical Manufacturers Association All rights reserved including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American Copyright Conventions.

20、 No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. Printed in the United States of America ANSI C136.10-2017 Page ii 2017 National Electrical Manufacturers Association ANSI C136.53-2017 Pa

21、ge iii 2017 National Electrical Manufacturers Association CONTENTS 1 Scope 1 2 Normative References 1 3 Informative Reference . 2 4 Mounting Provisions 2 5 Electrical Connections and Wiring 2 6 Assembly Features . 3 7 Voltage Classification 3 8 Lamp Socket . 3 9 Refractor and Lens Replacement . 3 10

22、 Ingress Protection . 3 11 Light Distribution . 4 12 Ballast or Driver . 4 13 Starter 4 14 Barriers 4 15 Photocontrol Receptacle . 4 16 Material and Protective Coatings 5 17 Labeling and Luminaire Identification . 5 ANSI C136.10-2017 Page iv 2017 National Electrical Manufacturers Association ANSI C1

23、36.53-2017 Page 1 2017 National Electrical Manufacturers Association 1 Scope This standard covers dimensional, maintenance, and light distribution features that permit the interchange of enclosed pendant-mounted luminaires whose center mass is directly below the mounting bracket. Luminaires of simil

24、ar size, shape, and weight meeting the requirements of this standard may be used interchangeably within a system with the assurance that: a) They will fit the mounting pendantb) Pole strength requirements will not changec) Light distribution will be similard) Similar maintenance procedures can be us

25、ed2 Normative References This standard incorporates by undated reference provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed below. For undated references, the latest edition of the publication referred to ap

26、plies (including amendments). ANSI/ASME B1.20.1 American National Standard for Pipe Threads, General Purpose (inch) ANSI C82.4 American National Standard for Ballast for High-intensity Discharge and Low-pressure Sodium Lamps (Multiple-supply Type) ANSI C136.2 American National Standard for Roadway a

27、nd Area Lighting EquipmentLuminaireDielectric Withstand and Electrical Transient Immunity Requirements ANSI C136.3 American National Standard for Roadway and Area Lighting EquipmentLuminaire Attachments ANSI C136.4 American National Standard for Roadway and Area Lighting EquipmentSeries Sockets and

28、Series-socket Receptacles ANSI C136.10 American National Standard for Roadway and Area Lighting EquipmentLocking-type Photocontrol Devices and Mating ReceptaclesPhysical and Electrical Interchangeability ANSI C136.11 American National Standard for Roadway and Area Lighting EquipmentMultiple Sockets

29、ANSI C136.15 American National Standard for Roadway and Area Lighting EquipmentLuminaire Field Identification ANSI C136.21 American National Standard for Roadway and Area Lighting EquipmentVertical Tenons Used with Post Top-mounted Luminaires ANSI C136.22 American National Standard for Roadway and A

30、rea Lighting EquipmentInternal Labeling of Luminaires ANSI C136.31 American National Standard for Roadway and Area Lighting EquipmentLuminaire Vibration ANSI C136.33 Plug-in Type Receptacle and Plug for High Intensity Discharge Lamp Ignitors ANSI C136.37 American National Standard for Roadway and Ar

31、ea Lighting EquipmentSolid State Light Sources ANSI C136.41 American National Standard for Roadway and Area Lighting Equipment - Dimming Control between an External Locking Type Photocontrol and Ballast or Driver ANSI C136.53-2017 Page 2 2017 National Electrical Manufacturers Association ASTM B117 S

32、tandard Practices for Operating Salt Spray (Fog) Apparatus ASTM D523 Standard Test method for Specular Gloss ASTM D1654 Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments ANSI/IESNA RP-8-2014 Roadway Lighting ANSI/IEC 60529 2004 American National S

33、tandard Degrees of Protection Provided by Enclosures (IP Code) (identical national adoption) NFPA 70 National Electrical Code3 Informative Reference This standard is intended to be used in conjunction with the following publication. The latest edition of the publication applies (including amendments

34、). ANSI C136.21 American National Standard for Roadway and Area Lighting EquipmentVertical Tenons Used with Post Top-mounted Luminaires 4 Mounting Provisions 4.1 NPT Thread Mount The luminaire/mounting housing shall be tapped with internal 1 in., 1 in., or 2 in. NPT pipe threads, per ANSI/ASME B1.20

35、.1. The luminaires shall also have provisions for applying a wrench to tighten as per manufacturers specifications and to provide anti-rotation. 4.2 Ball-and-Socket Style Mount Ball-and-socket style mount shall have restriction ring securely attached to the luminaire. Restriction ring shall be desig

36、ned to be securely clamped inside an arm and/or adapter bracket and shall meet the leveling requirements in clause 4.3. 4.3 Leveling The mounting mechanism shall allow for the luminaire to self-level; allowing the luminaire to remain 1 from vertical. 5 Electrical Connections and Wiring 5.1 Terminal

37、Block If a terminal block is specified, then it shall be a closed-back, fully insulated terminal block with a minimum of two line-side pressure-type wire connectors having slotted-head captive screws shall be securely mounted in the luminaire, so that incoming conductors will clear all internal acce

38、ssories. Each connector shall accept only one conductor (either solid or stranded), from 14 American Wire Gauge (AWG) to 6 AWG copper/aluminum. All connectors shall be clearly designated and marked as to what leads to connect to them. 5.2 Connectors Internal to the Luminaire ANSI C136.53-2017 Page 3

39、 2017 National Electrical Manufacturers Association Each connectors terminal shall be rated for the wire being connected. No twist-on wire connector shall be used for any connection. 5.3 Supply Leads If instead of a terminal block, supply leads are provided in the luminaire, they shall conform to th

40、e color coding of the National Electrical Codefor the various voltages. Leads shall be properly secured with strain relief suitable for the wires and cables to prevent mechanical stress on the connection points in the luminaire. Leads shall extend a minimum of 12 inches outside the electrical cavity

41、 or as specified by the user to allow for splicing. Leads shall be between 12 and 18 AWG copper. 5.4 Wiring and Grounding All internal components shall be assembled and pre-wired so that the luminaire can be energized by line connections at the terminal block. Internal luminaire conductors shall hav

42、e insulation rated to exceed the maximum temperature inside. A means shall be provided for grounding the noncurrent-carrying metal parts of the luminaire. All wiring and electrical components (including the photocontrol receptacle) shall not exceed their temperature design limits when the luminaire

43、is operated. This includes draft-free air across the luminaire operating temperature or as otherwise specified. 6 Assembly Features The luminaires shall be constructed to securely attach or retain all internal components in their proper place without relying on gravity. Provision shall be made for s

44、upporting access closures while installing or servicing. Captive devices shall secure all access closures. 7 Voltage Classification The luminaire shall be 600-volt classification as defined in ANSI C136.2. 8 Lamp Socket 8.1 High-Intensity Discharge (HID) Luminaires Luminaires shall be equipped with

45、either a medium or mogul screw-based socket that meets requirements of ANSI C136.4 and ANSI C136.11. 8.2 Induction Luminaires Luminaires that are intended for use with induction lighting systems shall have a lamp mounting means that provides robust attachment and suitable thermal management per ANSI

46、 C136.38. 9 Refractor and Lens replacement The refractor or lens shall be retained so that it may be replaced without tools (preferred) or with a blade-type screwdriver (acceptable). Position-oriented refractors shall be clearly marked. 10 Ingress Protection The luminaire attachment shall be designe

47、d to prevent water from entering the luminaire once installed, as recommended by the luminaire manufacturer. The luminaire shall be water and particle resistant to ANSI C136.53-2017 Page 4 2017 National Electrical Manufacturers Association ANSI/IEC 60529 ingress protection rating IP54 or higher. If

48、application of sealant is necessary to properly seal the luminaire once installed, luminaire manufacturers installation instructions shall be followed. The optical cavity shall be water and particle resistant to ANSI/IEC 60529 ingress protection rating IP65 or higher. 11 Light distribution The light

49、 distribution shall be as defined in ANSI/IESNA RP-8. 12 Ballast or Driver 12.1 Ballast HID luminaires shall be equipped with a ballast to operate a high-intensity discharge lamp as specified on the nameplate described in the applicable American National Standard for the lamp. It shall also satisfy the dielectric withstand requirements as defined in Section 6 of ANSI C136.2. 12.2 Driver Light-Emitting Diode (LED) luminaires shall be equipped with a driver that meets all the requirements in ANSI C136.37. 12.3 Additional Labeling In addition to the l