NAVY MIL-T-85031 B-1987 TEST SET GUIDED WEAPON AN DSM-96B《AN DSM-96B制导武器试验装置》.pdf

《NAVY MIL-T-85031 B-1987 TEST SET GUIDED WEAPON AN DSM-96B《AN DSM-96B制导武器试验装置》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-T-85031 B-1987 TEST SET GUIDED WEAPON AN DSM-96B《AN DSM-96B制导武器试验装置》.pdf（64页珍藏版）》请在麦多课文档分享上搜索。

1、Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving thio document should bc nddressed to: Commanding Off iccr, Haval Air Engliiecrlng Ccritcr, Systeiiis EiiqlrieerirY aid Standardiratlon Departmcnt (SESD) Code 53, Lakehurst, NJ 08733-51

2、00, by usin9 the self-rddresscd Stondardirat ion Document Improvcmcnt Proposal, (DO Form 1426) owesring OC the end of thls document or by letter. SUPERSEDING 7 November 1984 MIL -T-8503 lA(AS) MILITARY SPECIFICATION TEST SET, GUIDED WEAPON AN/DSM-96B This specification is approved for use within the

3、 Naval Air Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope, This specification estblishes the design, performance, and acceptance requirements for the AN/DSM-96B Guided Weapon Test Set herein referred

4、to as the test set. The test set is to be used at shore installations to verify the operability and flight readiness of assembled Wal 1 eye Guided Weapons. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following speciMcations and standards form a part of t

5、his specification to the extent- specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specificat-ions and Standards (DODISS) and supplement thereto, cited in the solicitation. I I r AMSC N/A DISTRIBUTION

6、STATEMENT A. Approved for public release; THIS DOCUMENT CONTAINS _h - 3/ PAGES. -. , FSC 4935 distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-T-8503LB 47 = 777770b 0257983 7 = MI L-T-8503 1 B (AS) SPECIFICATIONS MI L I

7、TARY MIL-T-17296 MIL-E-17555 MIL-T-18303 MIL-T-28800 MIL-T-85472 STANDARDS MILITARY MIL-STD-454 MIL-STD-965 Test, Checkout and Evaluation Equipment Guided Missiles (Fixed Installations), General S.pecification Electronic and Electrical Equipment, Accessories, and Repair Parts, Packaging and Packing

8、of Test Procedures; Preproduction, Acceptance, and Life for Aircraft Electronic Equipment, Format for Test Equipment for Use with Electrical and Electronic Equipment, General Speci fi cat i on for Test Set, Group OQ-169B/DSM-96A Standard, General Requirements for Electronic Equipment Parts Control P

9、rogram 2.1.2 Other Government drawings and publications. The following other Government drawings and publications form a part of this specification to the extent specified herein. the issues shall be those in effect on the date of the solicitation. Unless otherwise specified, DRAW I NG NAVAL AIR SYS

10、TEMS COMMAND DL 130AS200 DL 132AS500 DL 131AS200 Data List for Test Set, AN/DSM-96B and all drawings therein. MANUALS NAVAL AIR SYSTEMS COMMAND NAVAIR 16-30DSM96-3 Technical Manual, Service and Calibration Instructions, Guided Weapon Test Set AN/DSM-96B NAVAIR. 16-30DSM96-4 I1 1 ustrated Parts Break

11、down for Guided Weapon Test Set AN/DSM-96B 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-8503LB 47 W 7977906 0257484 O W MI L-T-8503 1 B (AS) (Copies of specifications, standards, drawings, and other Government documents required by the con

12、tractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contract i ng act i vi ty . ) 2.2 Order of precedence. In the event of a conflict between the text of this specification and the referenc cited herein (except for Che ass

13、ociated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede appl i cab1 e 1 aws and regul ati ons un1 ess a speci fi c exemption has been obtained. 3. REQUIREMENTS 3.1 Item descrip

14、tion. The Guided Weapon Test Set AN/DSM-96B shall consist of the Guided Weapon Test Console OJ-115B/DSM-96, Guided Weapon Test Stand MT-3707C/DSM-74 and cable assemblies. -The test set shall be capable of testing all non telemetry Walleye weapons. Group OQ-169B/DSM-96A Test Set (see MIL-T-85472), th

15、e test sets shall also be capable of testing the Extended Range Data Link, Phase I and Phase II Walleye weapons. Weapon Test Console OJ-306B/DSM-96A, Phase I Antenna Shroud, Phase II Antenna Shroud, and Weapon Antenna Attenuator Load. Guided Weapon Test Set AN/DSM-96B and the Group OQ-169B/DSM-96A T

16、est Set interconnected in a weapon test configuration. Detail operational instructions are specified in NAVAIR 16-30DSM96-3 and NAVAIR 16-30DSM96-4. 3.2 Parts and materials. When used in conjunction with The Group OQ-169B/DSM-96A Test Set consists of Guided Figure 1 shows the 3.2.1 Nonstandard parts

17、 and material approval. Approval for the use of nonstandard parts and materials shall be obtained by the contractor as specified in MIL-STD-965. 3.2.2 Basic conformance. test set shall be as specified in MIL-T-17296. Parts shall be selected from those conforming to MIL-T-28800, unless the.parts sele

18、cted will not perform as required in the intended applications and environments specified herein, in which case 3.2.1 applies. Materials and parts selected for use in the 3.2.3 Interchangeability. The test shall meet the interchangeability requirements of MIL-T-17296. The drawings listed in DL 130AS

19、200 shall be the standard for measuring interchangeability of all applicable units, assemblies, subassemblies, and parts. 3.3 Design and construction. The test set shall be manufactured in accordance with the drawings and subsidiary specifications listed in DL 130AS200, except in so far as errors of

20、 omissions or commission on the .drawings may be incompatible with the requirements of this specification. In any case, it is a condition of final acceptance that the test set manufactured shall meet all the design, construction, and workmanship requirements of this specification and applicable acce

21、ptance test documents. O 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-85031B Li7 m 777770b 0257485 2 m I I I I I I I I I I I I I I I I J FIGURE 1. Guided Weapon Test Set AN/DSM-96B interconnected with OQ-169B/DSM-96A Test Set. 4 Provided b

22、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-850316 47 m 7777706 0257486 4 m 3.3.l Reliability. 3.3.1.1 Operational stability. The test set shall operate as required, continuously or intermittently, for a period of at least 200 hours. this time, it sh

23、all not be necessary to readjust any controls that are inaccessible to the operator during normal use. During a 3.3.1.2 Operating life. The test set shall have a total operating life of 18,000 hours with minimum servicing and replacement of parts. 3.4 Standard conditions. The following conditions sh

24、all be used to establish the normal performance characteristics under standard conditions for performing laboratory bench tests: a. Temperature Room ambient (2555OC) b. Altitude c. Vibration d. Humidity e. Input Power (1) Console (2) Test Stand Normal ground None Room ambient up to 90 percent relati

25、ve humidity 115 +11.5 volts ac, 60 +5 Hz, single phase. 400 +40 Hz, three phase (Wye) (phase rotation A-B-C). 115/200 211.5 volts ac, 60 k5 Hz, 24,000 VA, three phase (Wye) (phase rotation A-B-C). 115/200 volts ac t10 percent, 3.4.1 Service conditions. The test set shall operate as required under an

26、y of the environmental service conditions or combination of these conditions as specified in MIL-T-17296 for shore installation equipment, except as modified in 3.4.1.1 and 3.4.1.2. 3.4.1.1 Temperature. The test set shall meet the specified performance within the ambient temperature limits of 32OF (

27、OOC) and 122OF (5OOC). 3.4.1.2 Altitude. The test set shall meet the specified performance at altitudes between O and 10,000 feet (normal ground). 3.4.2 Warm-up time. The time required for the test set (except the target simulator) to warm-up prior to operation shall be not greater than 30 minutes u

28、nder standard conditions. warm-up prior to operation shall be not greater than 2 minutes under standard conditions. The time required for the target simulator to 3.4.3 Primary input power. The test set shall be capable of required performance when supplied input power having characteristics as speci

29、fied herein. The input power shall be of the following types and shall be not greater than the amounts specified, except for transients caused by drive motor start-ups. a 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-8503LB 47 W 7777706 025

30、7487 b W MIL-T-85031B(AS) a. Console b. Test Stand AC power single phase, 115 i11.5 v, 60 Hz, 3,400 VA. AC power, three phase (Wye) , 115/200 - t11.5 v, 400 t40 Hz, 700 VA, (phase rotation A-B-C). AC power, three phase (Wye), 115/200 v, 60 Hz, 24,000 VA, (phase rotation A-B-C). 3.4.3.1 Primary overl

31、oad prouzction. The test set shall be capable of required performance when protected against electrical over1 oad as fol 1 ows: a. The primary power input shall be fused or equipped with magnetically operated instantaneous-trip circuit breakers. b. Electric motors of 10 or more horsepower rating sha

32、ll be equipped with heater overload protective devices. 3.5 Performance. The performance of the test set shall be as specified in 3.5.1 through 3.5.4.1 plus any and all performance requirements specified in DL 130AS200. Unless otherwise specified herein, these requirements shall apply under standard

33、 service conditions. When reduced performance requirements for service conditions are acceptable, such variations are speci fi ed herein. 3.5.1 Test Set, Guided Weapon AN/DSM-96B. The Test Set, Guided Weapon AN/DSM-96B, shall be manufactured in accordance with DL 130AS200, and shall meet all of the

34、requirements stated therein and in 3.6.1.1. the test set. Figure 1 shows 3.5.1.1 Test set functions (descriptive). The general functions of the test set shall be as follows: a. Provides inputs (mechanical, electrical, and optical) to the weapon under test (see table I). b. Verifies the flight-ready

35、condition (GO or NO-GO) of each assembled weapon (less wings and fins) under test thereon, for weapons listed in table I. (Fuze is not electrically checked.) c. Electrically isolates any control or guidance section of weapons listed (see table I) which exhibits a NO-GO indication for azimuth and ele

36、vation guidance signals, but not for azimuth and elevation gimbal angle signals. The optional gravity trim test wi.11 isolate between guidance section or control section failures. d. Rechecks the flight readiness of the reassembled weapon under test when the guidance section or control section has b

37、een replaced, 3.5.2 Test Console, Guided Weapon OJ-115B/DSM-96. The Test Console, Guided Weapon OJ-115B/DSM-96, hereinafter referred to as the test set console, shall be manufactured in accordance with DL 130AS200, and shall meet all of the requirements stated therein and in 3.5.2.1. 6 Provided by I

38、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-T-850318 49 m 7799906 0257488 8 m M I L - T- 8503 1 B (AS) 3.5.2.1 Test set console functions. console shall be as follows: The general functions of the test set a. Controls all test stand and weapon functions b

39、y remote command signal s. b. c. indicates the weapon conditions and the test stand functions: Provides measurement and visual di-splay of the weapon video output by the use of an oscilloscope, and provides for a check of resolution and shades of gray on the television monitor. Measures the generate

40、d torque at each of the four fin servo shafts, and displays the results as a GO/NO-GO indication with selectable numerical readout. d. 3.5.3 Stand, Test, Guided We.apon MT-3707C/DSM-74. The Test Stand, Guided Weapon MT-3707C/DSM-74, hereafter referred to as the test stand, shall be manufactured in a

41、ccordance with DL 132AS500, and shall meet all of the requirements stated therein and in 3.5.3.1. 3.5.3.1 Test stand functions. The functions of the test stand shall be as fol 1 ows : a. b. C. d. e. f. 9. h. 3.5.3.2 assembl a. b. Provides the necessary supports to mount the weapon under test. Provid

42、es electromechanical drive for the ram air turbine (RAT) generator of the weapon under test by use of a 10 horse power (H.P.) synchrogear motor. Provides 20-degree counterclockwise roll for non-data link and 45- degree counterclockwise roll for Phase I and Phase II weapon under test (as viewed from

43、the RAT drive motor), while mounted on the test stand. Provides a simulated target display to the seeker of the weapon under test and controls the positioning of the target simulator. Converts the mechanical torque generated at each of the control fin drive pins of the weapon under test to electrica

44、l signals for display as a GO/NO-GO indication on the test set console. Provides a common boundary (interface) between the test set console and the weapon under test. Provides target line-of-sight angular measurement along both X and Y axes. Provides automatic test set shutdown in the event weapon v

45、ibration or servo temperature exceeds al 1 owabl e 1 eve1 s. Test stand content. The test stand shall contain the following es: Drive (ram air turbine drive motor) syncogen motor. Weapon support (mounting). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

46、-,-,-MIL-T-8503LB 47 777770b 0257487 T W MIL-T-85031B (AS) c. Target (simulated target) and light source. 3.5.4 Cable assemblies. Cable assemblies shall. be manufactured in accordance with DL 130AS200,-and shall meet all of the requirements stated therein and in 3.5.4.1. 3.5.4.1 Cable assembly funct

47、ions, The functions of the cable assemblies shall be as follows: a. Connects the proper power to the test set. b. Interconnects the components of the test set. c. Interconnects the weapon being ested to the tes set. 3.6 Detail requirements. 3.6.1 Test Set, Guided Weapon AN/DSM-96B. The test set shal

48、l be manufactured in accordance with DL 130AS200 and this specification, and shall meet the requirements of 3.6.1.1 and 3.6.1.1.1. 3.6.1.1 Test set functions. When interconnected in accordance with DL 130AS200 and as shown on table II, with the proper input power ,applied (see 3.4.3), and when prope

49、rly connected to the Detailed Functional Requirements Test Circuitry (see figure 2); the Detailed Functional Requirements (see table II) shalT be met by the test set. -3.6.1.1.1 Test circuitry. be used to determine the GO/NO-GO lamp indications required in table II. Figure 3 provides the lamp sequence for the Automatic Track Test. specifies the lamp sequence for the Automatic Torque Test. The test circuit setup shown on figure 2 shall Fig