NAVY MIL-T-82570 A-1975 TORPEDO TUBE SURFACE VESSEL MARK 32 MODS 5 AND 7 (FOR TORPEDOES MARK 44 MOD 1 AND MARK 46 MOD 1)《44号1模及46号1模32号5及7模鱼雷水平舰船鱼雷发射管》.pdf

《NAVY MIL-T-82570 A-1975 TORPEDO TUBE SURFACE VESSEL MARK 32 MODS 5 AND 7 (FOR TORPEDOES MARK 44 MOD 1 AND MARK 46 MOD 1)《44号1模及46号1模32号5及7模鱼雷水平舰船鱼雷发射管》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-T-82570 A-1975 TORPEDO TUBE SURFACE VESSEL MARK 32 MODS 5 AND 7 (FOR TORPEDOES MARK 44 MOD 1 AND MARK 46 MOD 1)《44号1模及46号1模32号5及7模鱼雷水平舰船鱼雷发射管》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-T-Z570A LO M 7797706 0362033 b M -. - - MIL-T-82570A(OS) 6 Januar?. 147.5 MIL-T-82570 (OS) Superseding 8 January 1969 MILITARY SPECIFICATION TORPEDO TUBE, SURFACE VESSEL, MARK 32 MODS 5 AND 7 (For Torpedoes Mark 44 Mod 1 and Mark 46 Mod 1) This specification is approved for use by all Depart- me

2、nts and Agencies of the Department of Defense. 1. SCOPE * 1.1 This specification establishes the requirements for the procurement of Torpedo Tube Assembly Mk 32 Mod 5 (NAVSEA LD 162165) and Torpedo Tube Assembly Mk 32 Mod 7 (NAVSFA LD 162166) for use on surface vessels. 2. APPLICABLE DOCUMENTS * 2.1

3、 The following documents of the issue in effect on the date of invita- tion for bids or request for proposals fom a part of this Specification to the extent specified herein. SPECIFICATIONS Military MIL-C- 104 Crates, Wood; Lumber and Plywood Sheathed, Nailed and Bolted MIL-P- 116 Preservation - Pac

4、kaging, Methods of MIL;S-901 MIL- C- 16 17 3 Shock Tests, H.I. (High-Impact); Ship- board Machinery, Equipment and Systems,- Requirements for Corrosion Preventative Compound, Solvent Cutback, Cold-Application THIS DOCUMENT CONTAiNS PAGES. , d d ( FSC 1045 I Provided by IHSNot for ResaleNo reproducti

5、on or networking permitted without license from IHS-,-,- MIL-T-2570A 10 7777706 0362032 MIL-T-82570A (OS) STANDARDS Military MIL- STD- 129 MIL-STD- 167 Marking for Shipment and Storage Mechanical Vibrations of Shipboard Equipment MIL-STD-810 Environmental Test Methods DRAW1 NG S NAVSEA LD 162135 NAV

6、SEA LD 162155 NAVSEA LD 162165 NAVSEA LD 162166 NAVSEA Dwg 694718 NAVSFA Dwg 694720 NAVSEA qg 694627 NAVSEA Dwg 694631 NAVSEA Dwg 694740 NAVSEA Dwg 694741 2 Torpedo Tube, Surface Vessel, Mk 32 Mod 5 (Assembly) Torpedo Tube, Surface Vessel, Mk 32 Mod 7 (Assembly) Torpedo Tube, Surface Vessel, Mk 32 M

7、od 5 (Assembly), Index to List of Drawings Torpedo Tube, Surface Vessel, Mk 32 Mod 7 (Assembly), Index to List of Drawings Torpedo Tube, Surface Vessel, Mk 32 Mod 5 (Assembly) Torpedo Tube, Surface Vessel, Mk 32 Mod 7 (Assembly) Torpedo Tube, Surface-Vessel, Mk 32 Mods 5 and 6, Electrical Schematic

8、Torpedo Tube, Surface Vessel, Mk 32 Mods 7 and 8, Electrical Schematic Torpedo Tube, Surface Vessel, Mk 32 Mods 5 and 6, External Wiring Diagram Torpedo Tube, Surface Vessel, Mk 32 Mods 7 and 8, External Wiring Diagram Provided by IHSNot for ResaleNo reproduction or networking permitted without lice

9、nse from IHS-,-,-MIL-T-82570A (OS) NAVSEA Dwg 1623922 Pressure Gage . NAVSEA Dwg 1984119 Dummy Torpedo Mk 44 Mod 1 NAVSEA Dwg 2320787 “GO“ Gage, Barrel (Assembly) Torpedo Tube, Surface Vessel, Mk 32 Mods O thru 9 NAVSEA hg 2652289 Dummy Torpedo Mk 46 Mod 1 NAVSEA hg 3245120 Pressure Fikting Adapter

10、(Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting of- f icer . ) 2.2 Other publications. The following documents form a part of th

11、is specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for proposals shall apply. National Bureau of Standards Publications Handbook H28 Screw Thread Standards for the Federal Services (Application for copies should

12、be addressed,to the Superintendent of Documents Government Printing Off ice, Washington, DC 20402. ) 3. mQUIREMENTS 3.1 Description. Torpedo Tube Assemblies Mk 32 Mods 5 and 7 are pneu- matic launching devices capable of receiving, stowing, and launching Tor- pedoes Mk 44 Mod 1 and Mk 46 Mod 1. The

13、tube assemblies consist of three parallel barrels in triangular configuration, with three Breech Mechanisms Mk 1 Mod $ and torpedQ securing mechanisms, each an integral part of the barrels which are nested together on a common Training Gear Mk 11 Mod 1. Each barrel is capable of being selected and f

14、ired electrically from a remote location and of being manually fired at the tube in an emergency condition, During manual firing, a latch plate is swung open to provide automatic switching from normal to emergency torpedo gyro squib fire power for Torpedo Mk 46 Mod 1 and expose a manual firing butto

15、n to actuate the solenoid valve. The tube is equipped with two electrical junction boxes, one on each of the two lower barrels. ting functions from the fire control system and transmits them via electrical One box receives electrical preset- 3 Provided by IHSNot for ResaleNo reproduction or networki

16、ng permitted without license from IHS-,-,-MIL-T-82570A LO 9999906 0362034 L M cabling to each barrel-housed torpedo. butes the barrel ready, firing, and heating circuits. A charging line stowage tube is mounted on the uppermost barrel to accomodate the flexible charging hose. The only difference bet

17、ween the Mods 5 and 7 is in the electrical circuits: the Mod 5 is compatible with Fire Control Systems Mk 102, 105, and 111; the Mod 7 is compatible with Fire Control System Mk 114. Rie other box receives and distri- 3.2 General requirements .p: .p: 3.2.1 Preproduction sample. Unless otherwise speci

18、fied in the contract a preproduction sample of the torpedo tuhe asssinly is or order (See 6.2) required and shall be manufactured using the methods and procedures pro- posed for production. the purpose of determining that, prior to starting production the contractors production methods are capable o

19、f yielding items that comply with the technical requirements of the contract. The sample shall be tested as specified in 4.3.1 for 3.2.2 Materials. Unless otherwice specified in the contract, requisition or order, all materials and purchased parts entering into the final assembly of Torpedo Tubes Mk

20、 32 Mods 5 and 7 shall conform to the detailed require- ments given n the drawings and specifications listed in NAVSA LI) 162135 and LD 162155, respectively. . 3.2.3 Finishes,and coatings, construction, and dimensions. Finishes, coatings, construction, and dimensions shall Be in accordance with the

21、applicable drawings, specifications, and publications listed in NAVSEA LD 162135 and LD 1621-55 , respectively. 3.2.4 Moisture, fungus, and corrosion. The tubes shall be rendered moisture, fungus, and corrosion resistant in accordance with detail require- ments specified on drawings and specificatio

22、ns in NAVSEA LD 162135 and LD 162155, respectively. 3.2.5 Markinq. Marking of assemblies, subassemblies, and parts shall be in accordance with the applicable drawings listed in NAVSA LD 162135 and LD 162155, respectively. a 3.2.6 Threads. Unless. otherwise specified, all threads shall be in accordan

23、ce with National Bureau of Standards Handbook H28. The class or fit for threads shall be as specified on the applicable drawings. Xt 2? 3.2.7 Conflicting requirements. In the event of conflict between the documents referenced herein and the contents of this specification, the contents of this specif

24、ication shaI1 apply. 3.2.8 Safety precautions. All standard safety precautions for electrical apparatus and high pressure air shall be strictly observed, No test shall 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-be permitted to continue if in t

25、he opinion of the test engineer it is deemed unsafe, While conducting any of the firings, personnel shall stand clear of the breechward access opening and breech mechanism. Charging lines should be secured with safety chains when high pressure air charging operations are in progress. 3.3 Definitions

26、. For the purpose of this specification the following definitions are applicable: 3.3.1 Torpedo tube assembly. The launching device in its assembled state. 3.3.2 Nonoperating condition. The condition of the tube when assembled, prepared, issued, transported, and handled. 3.3.3 Loaded condition. inst

27、alled in the tube barrel, secured in place by the securing mechanism, and the breech mechanism and muzzle covers are installed. That condition when a torpedo or dummy is 3.3.4 Latched position of the breakaway plug puller mechanism. The break- away plug puller mechanism is latched when the latch is

28、in the breechward poci tion. 3.4 Performance requirements and product characteristics, Torpedo Tubes Mk 32 Mod 5 and Mk 32 Mod 7 shall meet the following performance requirements and product characteristics: 3.4.1 Hydrostatic pressure (breech mechanisms) The breech mechanisms shall withstand a hydro

29、static pressure of 4500 plus 20 minus O psig without failure of any part. * 3.4.2 Pneumatic system pressure drop. The pneumatic system of each barrel With the securing of the torpedo tube, minus the breech mechanism, shall be attached to a 2000 psi air source through a 0.024 inch diameter orifice. m

30、echanism removed and the manifold nipple blanked off, the pressure in the pneumatic system of each barrel shall stabilize at 1350 psig minimum. With the securing mechanism installed, the pressure shall stabilize at 750 psig minimum. At the completion of this test there shall be no deformation or fal

31、ureLof any part of the pneumatic system. 3.4.3 Breech mechanism air loss. sure of 2000 plus or minus 50 psig, allowed to cool or 2 hours, and then bled down to 1600 plus or minus 10 psig, none of the three breech mechanisms shall lose more than 5 percent air pressure, due to leakage, over a 24-hour

32、period. After being initially charged to a pres- * 3.4.4 Bore.size of barrel. Each barrel shall pass a “GO“ gage (NAVSE3 Dwg 2320787) with an axial force not to exceed 150 pounds. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-T-82570A LO 777

33、770b 03b203b 5 MIL-T-82570A(OS) 3.4.5 Electrical requirements 3.4.5.1 Dielectric strength. Electrical circuitry of the tube shall with- stand the application of a potential of 1000 volts ac between mutually insu- lated terminals and ground for one minute minimum without breakdown. * 3.4.5.2 Insulati

34、on resistance. Immediately following the dielectric strength test, the insulation resistance between hipotted points in the barrel circuits shall be 3 megohms minimum when a potential of 500 volts dc is applied. The insulation resistance between the hipotted points of the training gear heater circui

35、t shall be 0.5 megohm minimum when a potential of 500 volts dc is applied. 3.4.5.3 Circuitry, Electrical circuitry shall be in accordance with NAVSEA Dwg 694627 for Torpedo Tube Mk 32 Mod 5 and NAVSEA Dwg 694631 for Torpedo Tube Mk 32 Mod 7, as applicable. * 3.4.5.4 Training gear heater resistance t

36、est or current drain. The tor- pedo tube assembly training gear heater element resistance shall be 6.9 ohms plus 0.7 ohm or minus 0.4 ohm, or the heater element current drain at 115 volts plus or minus 0.5 volt ac input shall be 16.7 amps plus 1.1 amps or minus 1.6 amps, * 3.4.5.5 Barrel heater resi

37、stance, The total electrical resistance of the heater circuit for each barrel shall be 11.4 plus or minus 0.8 ohms. * 3.4.5.6 Heater circuits operating current. When the electrical heating circuits of the torpedo tube are operating, the total maximum current drain shall be 50.5 amperes with an input

38、 of 115 plus or minus 0.5 volts ac. 3.4.6 Squib fire switches. The switch plunger shall move out forcefully when the latch plate is released. 3.4.7 Interlock switch. When the training gear is rotated outboard through 180 degrees from the zero degree relative position, the training gear interlock swi

39、tch shall be closed from 35 plus or minus 2.5 degrees to 145 plus or minus 2.5 degrees. 3.4.8 Training gear crank test. When the base of the torpedo tube is level, the force required to initiate movement of the training gear, applied tangentially to the arc described by the training gear crank handl

40、e, shall be not greater than 30 pounds. 3.4.9 Retractable stop. The retractable stop, when in the operating position, shall stop tube rotation at 45 degrees plus or minus 2.5 degrees from the zero position. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from I

41、HS-,-,-MIL-T-82570A LO m 7773906 0362037 7 MIL-T-82570A(OS) 3.4.10 Limit stops. The limit stops shall prevent an arc of train in excess of 190 degrees. 3.4.11 Muzzle cover seal test. The axial force required to remove the muzzle cover shall be 30 plus or minus 10 pounds. 3.4.12 Ready light switch. W

42、hen the switch actuator plate on each control box is placed in the ON position, the ready light switch contacts shall close. * 3.4.13 Pressure switch operation. The pressure switch contacts in each barrel shall close at 1275 psig plus or minus 75 psig with increasing pres- sure and remain closed at

43、pressures above this value. The pressure switch contacts shall open at 1275 plus or minus 75 psig on falling pressure and remain open at pressures below this value. 3.4.14 Breakaway plug puller mechanism 3.4.14.1 The lever of the breakaway plug puller mechanism shall be capable of being latched and

44、unlatched by hand. 3.4.14.2 The breakaway plug puller mechanism shall permit dry firings when in the latched position and shall remain iii the latched position at the corn- pletion of these firings. * 3.4.14.3 The breakaway plug, during torpedo firings, shall pull away from the torpedo receptacle in

45、 Torpedoes Mk 44 Mod 1 and Mk 46 Mod 1 without damage and shall not affect torpedo exit velocities when the tube is fired at pres- sures of 1200 through 1500 psig. 3.4.15 Control valve operating lever. Each barrel of the tube shall not be capable of being fired, either electrically or manually, unti

46、l the control valve operating lever is placed in the READY condition. 3.4.16 Solenoid voltage. The solenoid firing valve for each barrel shall operate thgoughout an input voltage range of 102 to 124 volts ac, 60 Hz, single phase. * 3.4.17 Manual firing, The axial force that must be applied on the ma

47、nual firing button to initiate the firing cycle at pressures of 1200 through 2000 psig shall not exceed 25 pounds. * 3.4.18 Dry firing test. Each barrel of the torpedo tube assembly shall be capable of being fired, without a torpedo, by mechanical means at any flask pressure from 1200 to 2000 psig a

48、nd by electrical means when the solenoid valves are energized for 400 milliseconds maximum at any flask pressure of 1350 through 2000 psig without damage, malfunction, or hindrance to subsequent firings with a torpedo. 7 J Provided by IHSNot for ResaleNo reproduction or networking permitted without

49、license from IHS-,-,-1c.- - MIL-T-8257QATO .I 7749706 03b2038 7 m I MLL-T- 82570A (OS) J; 3.4.19 During dry firings of the tube and firings of dummy Torpedoes Mk 44 Mod 1 and Mk 46 Mod 1 at pressures of 1200 through 1500 psig, the plug puller mechanism shall move automatically from the unlatched to the latched position. being unlatched by hand. Upon completion of firings, the lever shall be capable of 3.