NAVY MIL-STD-1323-201-1979 UNIT LOAD FOR UNDERWAY REPLENISHMENT CARTRIDGE 5 125 MK 186 (TORCH) IN PALLET ADAPTER MK 144《5 125弹药筒航行的负载》.pdf

《NAVY MIL-STD-1323-201-1979 UNIT LOAD FOR UNDERWAY REPLENISHMENT CARTRIDGE 5 125 MK 186 (TORCH) IN PALLET ADAPTER MK 144《5 125弹药筒航行的负载》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-STD-1323-201-1979 UNIT LOAD FOR UNDERWAY REPLENISHMENT CARTRIDGE 5 125 MK 186 (TORCH) IN PALLET ADAPTER MK 144《5 125弹药筒航行的负载》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、i . / MIL-STD-1323 -201 1 9797911 0071q52 T n MILITARY STANDARD MIL-STD-1323-201 (NAVY) 2 NOVEMBER 1979 UNIT LOAD FOR UNDERWAY REPLENISHMENT CARTRIDGE, 5.125 INCH, MK 186 (TORCH) IN PALLET ADAPTER, MK 144 UNIT LOAD DATA DODIWNALC NO. EW75 NUMBER OF CARTRIDGES PER CONTAINER 1 NUMBER OF CONTAINERS PER

2、 ADAPTER UNIT 12 NUMBER OF ADAPTER UNITS PER UNIT LOAD . 2 NUMBER OF CARTRIDGES PER UNIT LOAD 24 58 LBS 758 LBS 116 LBS 12 LBS 94 LBS 1614 LESA GROSS WEIGHT OF ONE CONTAINER (APPROX). . GROSS WEIGHT OF ONE ADAPTER UNIT (APPROX) . WEIGHT OF ADAPTERS (APPROX) 2 58 LBS . WEIGHT OF STEEL STRAPPING (APPR

3、OX) . WEIGHT OF PALLET (APPROX) . GROSS WEIGHT OF UNIT LOA3 (APPROX) CUBE . 42.1 CU. FT. HAZARD CLASSIFICATION DOT . CLASS B CG CLASS II - G ADO NOT USE FOR SHIPPING PURPOSES DO NOT STACK MORE THAN 5 UNIT LOADS HIGH IN STORAGE AA NOTES: 1. 2. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES. FOR

4、CROSS REFERENCE TO ASSOCIATED TRUCKLOADING, CONTAINERLOADING AND CARLOADING MILITARY STANDARDS, REFER TO INDEX TO STANDARDS, MIL-HDBK-236 (NAVY) 1- REQUIREMENTS FOR CONSTRUCTION OF THIS UNIT LOAD SHALL CONSIST OF THIS DOCUMENT AND THE LATEST THIS UNIT LOAD IS AUTHORIZED AND RELEASED FOR sHiPPiNG, HA

5、NDLING STORAGE AND TRANSFER-AT-SEA. IT MAY ALSO BE USED FOR DOMESTIC SHIPMENT IN COMPLIANCE WITH DOT REGULATIONS. ISSUE OF MIL-STD-1323 (NAVY) I I 802.5- roh hs ORIGIN ATOR DATE NAVAL WEAPONS HANDLING CENTER WPNSTA EARLE, NEW JERSEY 0 n . Provided by IHSNot for ResaleNo reproduction or networking pe

6、rmitted without license from IHS-,-,- - MIL-STD-1323 -201 81 W 7777711 0073453 1 W: h MI 1-STD-1323-201 (NAVY) PALLELLZING PROCEDURE (a) THREAD STRAPPING, ITEM 7, BETWEEN THE DECK WIRES OF THE PAUET, ITEM 1, AS SHWN IN DETAIL A. (b) THREAD STRAPPING, ITEM 8, THROUGH THE SQUARE OPENINGS IN THE PALLET

7、 DECK AS SHOWN IN MTAIL A. (c) POSITION STRAPPING, ITEM 5, USED TO UNITIZE MODULE, ON PALLET ABOVE STRAPPING, ITEM 7, AS SHOWN IN DETAIL B. (d) THREAD STRAPPING, ITEM 6, THROUGH THE STRAP LOOPS OF THE FRONT AND REARFRAMES, ITEMS 2 AND 3, AND POSITION THE FRAMES ON THE PALLET AS SHOWN IN DETAIL B. (e

8、) POSITION TWO CONTAINERS IN THE CORNERS OF THE FRAMES WITH THEIRCOVER ENDS AGAINST THE FLANGE OF THE FRONT FRAME, ITEM 2, AND THEIR BOTTOM ENDS ON THE SPACER BLOCKS OF THE REAR FRAME, ITEM3, AS SHOWN IN DETAILS BAND C. (f) POSITION A THIRD CONTAINER BETWEEN THE WO COMAINERS WITH THE COVER ENDAGAINS

9、T THE FLANGE OF THE REAR FRAME. (s) POSITION THE REMINING THREE RCYiS OF CONTAINERS, ALTERNATING THE DIRECTION OF THE CONTAINERS BETWEEN RWS, AS SHWN IN DETAIL B. 6) POSITION THE TOP FRAME, ITEM 4, OVER THE FRAMES AND CONTAINERS WITH THE TWO SPACER BLOCK END OVER THE FRONT FRAME. (I) POSITION STRAPP

10、ING, ITEM 5, IN THE CORNER NOTCHES AND OVER THE TOP FRAME. TENSION AND DOUBLE NOTCH THE SEAL, ITEM 9. (i) THREAD STRAPPING, ITEM 6, THROUGH THE OUTBOARD STRAP LOOPS OF THE FRONT AND REAR FRAMES. TENSION AND DOUBLE NOTCHTHE SEAL, ITEM 9. 6) REPEAT STEPS (c) THROUGH (i) FOR THE SECOND ADAPTERUNIT. (I)

11、 THREAD STRAPPING, ITEM 8, UP THROUGH THE STRAP LOOPS OF THE FRONT AND REAR FRAMES AND OVER THE TOP FRAMES. TENSLON AND DOUBLE NOTCH THE SEAL, ITEM 9. (m) POSITION STRAPPING, ITEM 7, TO SECURE LOAD TO PALLET,OVER THE ADAPTER UNIT STRAPPING, ITEM 5. TENSION AND DOUBLE NOTCH THE SEAL, ITEM 9. MARKING:

12、 THE UNIT LOAD SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-1323 (NAVY). DEPALLUIUNG PROCEQURE (a) CUT AND REMOVE THE PALETIZING STRAPPING, ITEMS 7 AND 8. -1 DO NOT CUT ADAPTER UNIT STRAPPING, ITEMS 5 AND 6, IF THE ADAPTER UNITS ARE TO BE HANDLEDbRANSFERRED BEFORE REMOVING THE CONTAINERS. g) CUT AND R

13、EMOVE THE ADAPTER UNIT STRAPPING, ITEMS 5 AND 6. (c) REMOVE TOP FRAME. (d) REMOVE COMAINERS. (e) REMOVE FRONT AND REAR FRAMES. NOTES: 1. .o31 COLD ROLLED, HEAT TREATED, MAY BE SUJSTITUTED. 2. DO NOT USE TYPEISTRAPPING WITH POWER TOOLS. I LIST OF MATERIALS Provided by IHSNot for ResaleNo reproduction

14、 or networking permitted without license from IHS-,-,-MIL-STD-3323 -203 1 M 7777733 0073q54 3 M MIL-STD-1323-201 (NAVY) THREAD STRAPPING DOWN THROUGH THE SQUARE WHICH IS 2ND FROM THE END AND 3RD FROM THE SIDE THREAD STRAPPING BETWEEN THE 6TH AND TTH WIRE EDGE NOTCH APPLY THIS STRAP FIRST KEY B = BOT

15、TOM END C= COVER END - SEE DETAIL POSITION FRAMES WITH 1 INCH OVERHANG IN BOTH DIRECTIONS POSITION ON PALLET DECK IN LINE WITH EDGE NOTCHE THREAD THROUGH STRAP LOOPS 8 DETAIL 0 ADAPTER UNIT ASSEMBLY ON INBOARD SIDE BEFOB PLACING ADAPTER FRAMES ON PALLET DETAIL POSITIONING OF END FRAMES REVIEW ACTIVIT(; NAW - os PREPARING ACTIVITY. NAW - os (PROJECT NO. 8140-N467) PAGE 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-