CAN CSA-ISO IEC 14443-3F-2015 Identification cards - Contactless integrated circuit cards - Proximity cards - Part 3 Initialization and anticollision AMENDMENT 6 Bit rates of 3fc 4.pdf

《CAN CSA-ISO IEC 14443-3F-2015 Identification cards - Contactless integrated circuit cards - Proximity cards - Part 3 Initialization and anticollision AMENDMENT 6 Bit rates of 3fc 4.pdf》由会员分享，可在线阅读，更多相关《CAN CSA-ISO IEC 14443-3F-2015 Identification cards - Contactless integrated circuit cards - Proximity cards - Part 3 Initialization and anticollision AMENDMENT 6 Bit rates of 3fc 4.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、 ISO/IEC 2014. CSA Group 2015. All rights reserved. Unauthorized reproduction is strictly prohibited.Amendment 6:2015 (IDT) toCAN/CSA-ISO/IEC 14443-3:13(ISO/IEC 14443-3:2011, IDT)National Standard of CanadaAmendment 6:2015 (IDT) to CAN/CSA-ISO/IEC 14443-3:13Identification cards Contactless integrate

2、d circuit cards Proximity cards Part 3: Initialization and anticollisionAMENDMENT 6: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICC(ISO/IEC 14443-3:2011, IDT)Standards Update ServiceAmendment 6:2015 (IDT) to CAN/CSA-ISO/IEC 14443-3:13December 2015Title: Identification cards Contactless integ

3、rated circuit cards Proximity cards Part 3: Initialization and anticollisionAMENDMENT 6: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICCTo register for e-mail notification about any updates to this publication go to shop.csa.ca click on CSA Update ServiceThe List ID that you will need to regi

4、ster for updates to this publication is 2424064.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at www.csagroup.org/legal to find out how we protect yourpersonal information.Identification cards Contactless integrated circuit c

5、ards Proximity cards Part 3: Initialization and anticollisionAMENDMENT 6: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICCCartes didentification Cartes circuit(s) intgr(s) sans contact Cartes de proximit Partie 3: Initialisation et anticollisionAMENDEMENT 6: Dbits binaires de 3fc/4, fc, 3fc/2

6、et 2fc de PCD PICC ISO/IEC 2014INTERNATIONAL STANDARDISO/IEC14443-3Second edition2011-04-15Reference numberISO/IEC 14443-3:2011/Amd.6:2014(E)AMENDMENT 62014-06-01ISO/IEC 14443-3:2011/Amd.6:2014(E)ii ISO/IEC 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO/IEC 2014All rights reserved. Unless

7、otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the addr

8、ess below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgAmendment 6:2015 (IDT) toCAN/CSA-ISO/IEC 14443-3:13ISO/IEC 14443-3:2011/Amd.6:2014(E)ForewordISO (the In

9、ternational Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees estab

10、lished by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the

11、 field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of the joint technical committee is to prepare International Standards. Dra

12、ft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standard requires approval by at least 75 % of the national bodies casting a vote.Attention is drawn to the possibility that some of the elements of this

13、document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights.Amendment 6 to ISO/IEC 14443-3:2011 was prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 17, Cards and personal identifica

14、tion. ISO/IEC 2014 All rights reserved iiiAmendment 6:2015 (IDT) to CAN/CSA-ISO/IEC 14443-3:13Identification cards Contactless integrated circuit cards Pro ximity cards Part 3: Initialization and anticollisionAMENDMENT 6: Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICCPage 5, 6.1 (amended by

15、ISO/IEC 14443-3:2011/Amd.2:2012)Add the following after Table 1:“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.1.”Page 7, 6.2.1.1 (amended by ISO/IEC 14443-3:2011/Amd.2:2012)Add the following after second paragraph:“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.2.1.1.”Page 9, 6.2.1.1 (amended by

16、 ISO/IEC 14443-3:2011/Amd.2:2012)Complete the enumeration of bit rates in Table 2 by adding bit rates of 3fc/4, fc, 3fc/2 and 2fc in last row.Page 11, 6.2.3.2.2Add the following subclause and sentence after 6.2.3.2.2:“6.2.3.2.3 PCD standard frame for bit rates of 3fc/4, fc, 3fc/2 and 2fcSee E.2.2.1.

17、”Page 23, 7.1.1Add the following below Figure 13:“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.2.2.3.”Page 24, 7.1.3Add the following paragraph below Figure 14:“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.2.2.2.”Page 26, 7.1.4Add the following paragraph before 7.1.5:“For bit rates of 3fc/4, f

18、c, 3fc/2 and 2fc see E.2.2.2.”Page 27, 7.1.5Add the following paragraph at the end of the subclause:“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.2.2.2.”ISO/IEC 14443-3:2011/Amd.6:2014(E) ISO/IEC 2014 All rights reserved 1Amendment 6:2015 (IDT) to CAN/CSA-ISO/IEC 14443-3:13ISO/IEC 14443-3:2011/Am

19、d.6:2014(E)Page 28, 7.1.7Add the following paragraph at the end of the subclause:“For bit rates of 3fc/4, fc, 3fc/2 and 2fc see E.2.1.2.2.”After Annex D of ISO/IEC 14443-3:2011/Amd.2:2012Add the following Annex E:“2 ISO/IEC 2014 All rights reservedAmendment 6:2015 (IDT) to CAN/CSA-ISO/IEC 14443-3:13

20、ISO/IEC 14443-3:2011/Amd.6:2014(E)Annex E (normative) Bit rates of 3fc/4, fc, 3fc/2 and 2fc from PCD to PICCE.1 etuThe value of the etu for each bit rate is defined in Table E.1.Table E.1 e tuBit rates etu3fc/4 ( 10,17 Mbit/s)4/fc ( 0,29 s)fc ( 13,56 Mbit/s)4/fc ( 0,29 s)3fc/2 ( 20,34 Mbit/s)2/fc (

21、0,15 s)2fc ( 27,12 Mbit/s)2/fc ( 0,15 s)E.2 Frame format and timingThe frame format and timing requirements are defined in 6.2 for Type A and in 7.1 for Type B.E.2.1 Frame delay timeThe frame delay time is defined as the time between two frames transmitted in opposite directions.E.2.1.1 Frame timing

22、 PCD to PICCThis is the time between the end of the last phase modulation transmitted by the PCD and the first modulation edge transmitted by the PICC.E.2.1.1.1 Frame delay time PCD to PICC for Type AThe FDT shall be at least 1116/fc.E.2.1.1.2 Timing before PICC SOF for Type BThe timing before PICC

23、SOF as specified in 7.1.6 (amended by ISO/IEC 14443-3:2011/Amd.2:2012) shall be used.E.2.1.2 Frame timing PICC to PCDE.2.1.2.1 Frame delay time PICC to PCD for Type AThis is the time between the last modulation transmitted by the PICC and the beginning of the first phase modulation transmitted by th

24、e PCD.The Frame delay time PICC to PCD for Type A shall be at least 1172/fc. ISO/IEC 2014 All rights reserved 3Amendment 6:2015 (IDT) to CAN/CSA-ISO/IEC 14443-3:13ISO/IEC 14443-3:2011/Amd.6:2014(E)E.2.1.2.2 Timing before PCD start of communication for Type BThis is the time between the end of the la

25、st character transmitted by the PICC and the beginning of the first phase modulation transmitted by the PCD.The timing before PCD start of communication for Type B shall comply with the requirements defined in 7.1.7.E.2.2 Frame formatE.2.2.1 Frame format for PICC Type AThe standard frame format as d

26、efined in ISO/IEC 14443-3:2011/Amd.2:2012, 6.2.3.2.1 shall be used.Start and end of communication are specified in ISO/IEC 14443-2:2010/Amd.5.E.2.2.2 Frame format for PICC Type BThe frame format as specified in 7.1.3 shall be used whereas the frame shall be delimited by start and end of communicatio

27、n as specified in ISO/IEC 14443-2:2010/Amd.5.E.2.2.3 Character transmission format for PICC Type BThe character transmission format as specified in 7.1.1 shall be used whereas the start and stop bits shall be omitted and no character separation shall be applied.“4 ISO/IEC 2014 All rights reservedAme

28、ndment 6:2015 (IDT) to CAN/CSA-ISO/IEC 14443-3:13ISO/IEC 14443-3:2011/Amd.6:2014(E)ICS 35.240.15 ISO/IEC 2014 All rights reservedCopyright NoticeThe Canadian adoption of this Amendment to the International Standard contains information copyright protected by CSA Group. All rights reserved. No part o

29、f this adopted Amendment may be reproduced in any form whatsoever without the prior permission of CSA Group. ISO/IEC material is reprinted with permission.Requests for permission to reproduce this adopted Amendment or parts thereof should be addressed to:Manager, SalesCSA Group178 Rexdale BoulevardToronto, Ontario M9W 1R3Copyright violators will be prosecuted to the full extent of the law.