NAVY MIL-PRF-21479 B-1985 CABLE ASSEMBLIES GENERAL SPECIFICATION FOR (ORDNANCE)《一般技术要求无磁性缆索组件(军用器材)》.pdf

《NAVY MIL-PRF-21479 B-1985 CABLE ASSEMBLIES GENERAL SPECIFICATION FOR (ORDNANCE)《一般技术要求无磁性缆索组件(军用器材)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-PRF-21479 B-1985 CABLE ASSEMBLIES GENERAL SPECIFICATION FOR (ORDNANCE)《一般技术要求无磁性缆索组件(军用器材)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、I NOTE: fhe document identifier and heading has been changed onthis page to reflect that this is a pcrfortnaace specification. There arcno other changes to this document. The document on subequentpages has not been changed, but will be chaaged the next time thisdocument is revised.MIL-PRF-21479B(OS)

2、JM arch 1985SUPERSEDINGSee 6.3PERFORMANCE SPECIF1CATIONCABLES ASSEhfBLIES, GENERAL SPECIFICATION FOR(ORDNANCE)Thk specification is approved for use by Ihe Naval Sea Systems Command, Department of the Navy, and isavailable for use by all Departments and Agencies of the Department of Defense.1. SCOPE1

3、,1 Scope. This specification covers the requirements for the procurement of cable assemblies for use in ortesting of weapons and weapon components. Oble assemblies covered by this specification are of one type andclass.2. APPLICABLE DOCUhlEfWS2.1 Government documenLs.2.1.1 Specifications and Standar

4、ds. The following specifications and stmdnrds of the issue listed in theissue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitationform a part of this specification to the extent herein.SPECIFICATIONSMi!iLwMIL-C-S015 Connectors, Electrical, Circula

5、r Threaded, Generul Specification forSTANDARDSEE!lFED-STD-101 Test Pmedurrs for Packaging MaterialsM1L-STD-105 Sampling Procedures md Tables for Inspections by AttributesMIL-STD-129 Marking for Shipment and StorageBcneficidl comments (recommendation, additions, dclctitms) and any pertinent data whic

6、h may be of use in impmvingIbis docum.nt should be tddrc,sscd tw. Comrnading Officer, Naval Ordmmce Skuion, Snndmdkation Division (524),Indian Head, MO 20640-5035, by using the Slandardkalion Document Imprvvemcnt Prop-assf (DD Form 1.$26)aPWting at lhe end of lbk document or smding a later.FSC 1135P

7、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-M1L-C-21479B(OS)MIL-STD-202 Test Methods for Electronic and Electric Component Parts 4MIL-STD-331 Fuze and Fuze Components, Environmental and Performance Tests forMIL-ST.D-1310 Shipboard Bonding, Groundi

8、ng, and Other Techniques for Elec.trmrragnetic Compatibility and SafetyMIL-STD- 1364 Standard Genera) Purpose Electronic Test Equipment2.1.2 Other Government documents, drawings, .arrd prsblica!ions. The following Government drawingsform a part of this specification to the extent specified herein. U

9、nless otherwise specified, the issues shaffbe those in effect on the date of the solicitation.DRAWINGSNaval Sea Systems Command (Code Ident 10001)LD284865 Pepara!ion for Delivery of Cable AssernbtiesLD284866 Preparation for Devery of Test Set Cable Assemblies1358405 Preparation for Delivery of Cable

10、 Assemblies(Copies of specifications, standards, and drawings required by manufacturers in connection with specificacquisition functions should be obtained from the contracting officer). 42.2 Order of Precedence. In the event of a conflict between the text of this specification and the references Ic

11、ited herein, the text of this specification shaU take precedence.3. REQUIREMENTS3.1 Description. The cable assemblies covered by thk specification consist of insulated electrical con-ductors grouped together in cables, unterminated or terminated with AN connectors or other terminationas specified in

12、 the applicable drawing.3.2 Gerreral requirements.3.2.1 First article, When :pecified, a sample shall be subjected to first article inspection (see 4.4 and 6.4).3.2.2 Design and constuclion. The cable assemblies shall be manufactured in accordance with the draw-ing cited in the ordering document (se

13、e 6.2), all documents listed therein, and as specified herein. Non-portable cables or cable assemblies planned for installation in a ship topside area shall be suitably shieldedfor EMP protection or EMI reduction, as requiredbyMIL-STD-13 10. Inspection and acceptance shall bein accordance with secti

14、on 4.3.3 Perforrnrmce requirements and prodnclion characteristics. The cable assemblies shall meet the followingperformance requirements and product characteristics:NOTE: When specified in tbe contract, order or applicable drawing, the performance re-quirements aqd product characteristics specified

15、below maybe modified or omitted,and additional requirements may be included.2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-21479B(OS)1) 3.3.1 Connectors. After assembly, connectors of cable assemblies shaii show no damage, shall be capableIIo

16、f being fully mated and unmated by hand without the use of tools, and individual socket type contactsof connectors shall exhibit a force within allowable limits required to engage or disengage a correspondingpin contact, when tested as specified in 4.5.2.1.3.3.2 Electrical continuity. The d-c resist

17、ance between ail points connected by design shali be 0.2 ohmsor less when measured as specified in 4.5.2.2.3.3.2.1 Electrical continuity (connector pins in motion). When required by the contract, purchase orderOr rqpfible drawings, the cabie assemblies shaii meet the electrical continuity requiremen

18、ts Of 3.3.2 whilethe connector pins are in motion. Cable assemblies shali be tested for conformance to thk requirement,in accordance with 4.5.2.2.1. No erratic movement of the resistance-b ridge-null-indicator needle shaIl oc-cur during the electrical continuity measurements (see 6.2).3.3.3 Insulati

19、on resistance. Each circuit and each unused pin of the cabie assembly shall cshibit an in-sulation resistance of 50 megohms or more at a test potential of 500 * 50 volts dc (or other value of insula-tion resistance and test potentiai when specified by contract, purchase order or applicable drawing)

20、withrespect to alI other non-connected circuits and unused pins connected together, to the connector housingand to ground, The cable assembly shall be tested as specified in 4.5.2.3.2 after being conditioned as re-quired by 4.5.2.3.1.3.3.3.1 Insulation resistance (connector pins in motion). When req

21、uired by the contract, purchase order ior applicable drawings the cabie assemblies shafl meet the insulation requirements of 3.3.3 while tbe con-nector pins are in motion. Cable assemblies shali be tested for conformance to this requirement in accor-dance with 4.5.2.3.3. No erratic movement of the m

22、egohmmeter needie shall occur during the insulationresistance measurements (see 6.2).3.3.4 Dteiectric withslandirm voltage. The cable assemblies shall withstand the dielectric withstanding-.voltage test specified in 4.5.2.4. This test shall be required only when specified in the contract, purchaseor

23、der or applicable drawings (see 6.2).3.4 Environmental requirements.3.4.1 Vibration.3.4.1.1 Vibrsrtion, trmrsportation, storage and hmrdling. After a cable assembly has been mounted andtested as specified in 4.6. i .i, it shail show no evidence of damage and its function shall not be impaired.3.4.1.

24、2 Vibmtion, ready-nnn-operating. After a cable has been mounted and tc.sted as specified in 4.6.1.2,it shall show no evidence of damage and its function shall not be impaired.3.4.2 Shock.3.4.2.1 Shock, transportation, storage mrd brmdling. After a cable has been mounted and tested as specifiedin 4.6

25、.2.1, it shali show no evidence of damage and its function shall not be impaired.3.4.2.2 Shock, ready-non-operating. After a cable has been tested as specified in 4.6.2.2, it shall showno evidence of damage and its function shall not be impaired.3 IProvided by IHSNot for ResaleNo reproduction or net

26、working permitted without license from IHS-,-,-IIMIL-C-21479B(OS) a. . . . . !3.4.3 Temperature storage. The cable assemblies, packaged and packed in accordance with DrawingLD284865 shall be subjected to the temperature conditions specified in 4.6.3. After being subjected to the sspecified temperatu

27、re cycle, the cable assemblies shall show no damage or excessive corrosion and shallmeet all performance and product requirements of thk specification.3.4.4 Pressure. Cable assembka required to be submersible shafl withstand the test pressure specifiedfor the time specified (see 6.2) when tested in

28、accordance with 4.6.4.3.5 Clean-up. Prior to and afte final assembly, parts, components and the assembly shrdl bethouroughly cleaned of loose, spattered or excs solder, metal chips and other foreign matler. Burrs andsharp edges as well as rosin flstah shrdl be removed.3.6 Workmanship. The cable asse

29、mbly, including parts and accessories, shall be constructed and finish-ed in a manner to assure compliance with rdl requirements of this specification. Particular attention shrdfbe paid to neatness,”and thoroughns of soldering, wiring! markngof parts and assemblies, plating, pain-ting, riveting, mac

30、hine screw assemblage and freedom of parts from burrs and sharp edges. Conductorsshall not be damaged as a result of stripping of insation or crimping of terminals. The standards of workman-ship exhibited in any approved first article approvaI, shall determine the requirements of the ccntract relati

31、veto workmanship insofar as not spehcally covered by applicable specifications.4. QUALITY ASSURANCE PROVISIONS4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the con- “*tractor is responsible for the performrqrce of all inspection requirements as spcc

32、ifrcd herein. Except as otherwisespecified in the contract or purchase order, the contractor may use his own or any other facilities suitablfor the performance of the inspection requirements specified herein, unless disapproved by the Govern- ament. The Government reserves the right tn perform arry

33、of the inspections set forth in the specificationwhere such inspections are deeme necessary to assure supplies and services conform to prescribedrequirements.4.2 Classification of inspections. The inspection requirements specified herein are classified as follows:a. Fkst article inspection (see 4.3.

34、1).b. Quality conformance inspection (see 4.3.2).c. Periodic production inspection (see 4.3.3).4.3 Inspections.4.3.1 Fks( article inspection. A first article sampie of 20 cable assemblies manufactured in accordancewith 3.2.1 shall be subjected to the examinations and tests detailed in 4.5 and 4.6 at

35、 an activity designatedby the procuring activity. Acceptance of the sample examination and test shall be based on no defects inthis sample. When cable assemblies are required to be submersible, 25 units shall comprise a first article sample.4.3.2 Quality conformance inspection.4.3.2.1 100 percent in

36、spection. Each unit shall be subjected to the examination of 4.5.1 and tests designatedas 100 percent in 4.5.2. Any unit containing one or more defects shall be cause for regarding the unit asdefective. .+aIProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

37、-,-,-(IMIL-C-21479B(OS)-:94.3.2.2 Sampling. Tests designated as sample tests in 4.5.2 shall be conducted on a random sample ofcable assemblies selected from each production lot in accordance with tbe provisions of MIL-STD-I 05, in-spection level 11, AQL 0.25 percent defective. No lot shall be shippe

38、d until the samples representing thelot have successfully passed the quality conformance sampling tests. Unless otherwise specified in the con-tract or purchase order, a “lot” size shall be one months scheduled pr. uction (see 6.2). When the lotsize is increased the sample size shall be increased ac

39、cordingly.4.3.3 Periodic inspection. After successful completion of the quality conformance inspection of 4.5, theenvironmental test indicated in Table II shall be conducted on a random sample of six cable assembliesselected by the Government from each lot of cable assemblies offered for acceptance.

40、 when a unit failsto pass any environmental test or specified subsequent quality conformance test, examination of the unitshall be made by the contractor to analyze tbe cause of the failure and corrective action maybe taken. Whencause of the failure is determined to be a supplier nonconformance to t

41、he quality conformance test requirementsof this specification and/or its associated drawings, the contractor may be required to screen the lot andrepair or replace the discrepant part of material and resubmit the lot for complete retesting. When the cableassemblies are required to be submersible, ei

42、ght units shall comprise a periodic test sample (see 6.2).4.4 Test equipment. Items of test equipment which may be required to perform the tests set forth inthis specification are as follows. Selection of test equipment shall be made from MIL-STD-1364.NOTE The test equipment listed below covers the

43、tests specified to verify the performancerequirements and product characteristics. Where modifications in performance re-quirements and product characteristics are specified in the contract, or applicabledrawings, suitable additional test equipment shall be required to perform the addi-S tional acce

44、ptance tests specified.a. A resistance bridge, capable of measuring low resistance (O-1ohm) to an accuracy of * 2 percent.b. A megohmmeter, capable of measuring resistance to 1000 megohms to an accuracy of t 10 per-cent or better at a test potential of 500 * 50 volts dc.c. Equipment necessary to per

45、form the dielectric withstanding voltage tests specified in MIL-STD-202,Method 301.d. Special contact test pins, as required, which shall be mated with contact sockets of fully assembl.ed connectors when attached to the cable assemblies.4.5 Quality conformance inspection.4.5.1 Examination. Each cabl

46、e assembly shail be visually and dimensionally cxamioed in accordance withthe applicable classification of defects to determine compliance with this specification and those lists ofdrawings, standards and specifications listed on the applicable drawing. Any cable assembly containing oneor more defec

47、ts shall either be satisfactorily corrected before being returned to the lot or discarded. Ex-amination in accordance with the applicable classification of defects shall not relieve the contractor of hhresponsibility to meet all drawing requirements not listed on the classification of defects. Unles

48、s otherwisespecified, the classification for non-conforming unlisted characteristics or workmanship defects shall bedetermined by the contracting officer.pProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IMIL-C-21479B(OS)4.5.2 Tests.NOTES: 1. Test mob

49、es shall not be used to make electrion;ectors of special design. Jigs made up of mating connectors shall be used.Mating connectors may be wired or their solder pots maybe used as the test points.2. Where the contract, purchase order or applicable drawings specify performancerequirements and product characteristics in addition to those specified under 3.4,suitable acceptance tests, in addition to those listed below, sh be performed to verifythe characteristics s