NAVY MIL-PRF-18148 3-2011 RECEPTACLES ELECTRIC AIRCRAFT STORAGE BATTERY [Superseded NAVY MS3509 REV F CANC NOTICE 1 NAVY MS3509 REV F NAVY MS3509 REV E NAVY MS3509 REV D NAVY MS350飞机.pdf

《NAVY MIL-PRF-18148 3-2011 RECEPTACLES ELECTRIC AIRCRAFT STORAGE BATTERY [Superseded NAVY MS3509 REV F CANC NOTICE 1 NAVY MS3509 REV F NAVY MS3509 REV E NAVY MS3509 REV D NAVY MS350飞机.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-PRF-18148 3-2011 RECEPTACLES ELECTRIC AIRCRAFT STORAGE BATTERY [Superseded NAVY MS3509 REV F CANC NOTICE 1 NAVY MS3509 REV F NAVY MS3509 REV E NAVY MS3509 REV D NAVY MS350飞机.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-PRF-18148/3 28 March 2011 SUPERSEDING MS3509F 27 November 1985 PERFORMANCE SPECIFICATION SHEET RECEPTACLES, ELECTRIC, AIRCRAFT STORAGE BATTERY This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product describe

2、d herein shall consist of this specification sheet and MIL-PRF-18148. REQUIREMENTS: 1. Part or identifying number. The part or identifying number (PIN) of the receptacles covered by this specification sheet shall be MS3509-XX, where XX specifies a particular version of the receptacle. The MS3509-XX

3、receptacle is a component of aircraft storage batteries. 2. Dimensions and weight. The dimensions and weight of the receptacle shall be as specified in 3.12.3 of MIL-PRF-18148 and 3.12.4 as modified herein and as shown on the figures and table I contained herein. 3. Receptacles. The body of each rec

4、eptacle shall be molded in one piece from rigid insulating material. Conductive reinforcements may be provided for the mounting holes. The contacts shall be insulated from each other and from the reinforcements. 4. Gaskets. Gaskets shall be made of rubber conforming to requirements of ASTM D6576-07

5、for Type II, Grade A, and firm condition. 5. MIL-PRF-18148 variance. The receptacle shall comply with MIL-PRF-18148 except as follows. AMSC N/A FSC 5935 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 2 5.1 Modify the follo

6、wing paragraphs: 2.2.1 Specifications and standards. Add under STANDARDS: “FEDERAL STANDARDS “FED-STD-595/15042 - Blue, Gloss “FED-STD-595/17038 - Miscellaneous, Gloss “FED-STD-595/21158 - Red, Semigloss “FED-STD-595/25042 - Blue, Semigloss “FED-STD-595/27038 - Miscellaneous, Semigloss “FED-STD-595/

7、35042 - Blue, Flat or Lusterless “FED-STD-595/37030 - Miscellaneous, Flat or Lusterless “FED-STD-595/37031 - Miscellaneous, Flat or Lusterless” 2.3 Non-Government publications. Add the following: “ASTM INTERNATIONAL “D6576-07 - Standard Specification for Flexible Cellular Rubber Chemically Blown. (D

8、oD adopted)“ “(Copies of this document are available from http:/www.astm.org or ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.) “SOCIETY OF AUTOMOTIVE ENGINEERS “SAE-AS8879 - Screw Threads UNJ Profile, Inch Controlled Radius Root with Increased Minor Diamet

9、er. (DoD adopted)“ (Copies of this document are available from http:/www.sae.org or SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001.) 3.4 Materials and components. Insert after the second sentence: “Aluminun or polyester shall not be used in the construction of all MIL-PRF-18148

10、/3 receptacles. Nickel-plated ferrous steel shall not be used in the construction of MS3509-32 receptacles.“ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 3 3.8.2 Electrical connections. Insert after the first sentence: “Each recept

11、acle shall include two electrical connections of the type listed in table I of MIL-PRF-18148/3 and shall be integral with the contact pins. The connections and pins shall have a cross-sectional area of not less than 0.074 square inches at all points between the connections and the pins. The connecti

12、ons and pins shall have a conductive protective plating that will resist rusting and corrosion. Threads shall conform to SAE-AS8879.“ 3.10.1 Color. Insert after the first sentence: “The body of each receptacle shall be a color conforming to requirements of FED-STD-595 for color number 21158 (pink) o

13、r within the range of color numbers 15042, 17038, 25042, 27038, 35042, 37030, or 37031 (black).“ 3.12.4 Weight. Insert after the first sentence: “The weight of each MS3509-XX receptacle shall be not greater than the weight shown in table I of MIL-PRF-18148/3.“ 5.2 Add the following paragraph: “3.12.

14、17 Plating adhesion. Plating shall remain intact and the terminal blocks shall not be damaged after being tested in accordance with the plating adhesion test of 4.5.19 of MIL-PRF-18148/3. The items shall also meet the requirements of general requirement 3.11 of MIL-PRF-18148 during and after testing

15、.“ 5.3 Modify the following paragraphs of MIL-PRF-18148: 4.2 Qualification inspection. Insert after the end of the first sentence: “(see table II of MIL-PRF-18148/3).“ 4.3 Conformance inspection. Insert after the end of the first sentence: “(see table II of MIL-PRF-18148/3).“ 4.5.10 Receptacle stren

16、gth tests (applies only to receptacles). Insert before the first sentence: “Whenever a test screw is required for testing, a test screw (see figure 8 of MIL-PRF-18148/3) shall be used and shall be engaged with the plug retaining pins of the receptacle.” Replace section b with the following: “b. Enga

17、ge a test screw with the receptacle, but utilize a spacer to ensure the screw engagement pins are unable to reach the screw detent. Apply a torque of 150 10 inch-pounds to the screw for 5 1 seconds. Release the tension. Examine the receptacle for the requirements of 3.12.9 of MIL-PRF-18148.” Provide

18、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 4 4.5.15.1 Test solutions. Insert before the first sentence: “Pink receptacles shall not be subjected to the aqueous potassium hydroxide test solution of 4.5.15.1.a of MIL-PRF-18148.“ 5.4 Add t

19、he following paragraphs: “4.5.19 Plating adhesion. Bake samples of metal parts prepared as those supplied with assembled receptacles at 438 415 C (800 20 F) for 24 hours in an oven with a reducing atmosphere. Examine the samples for the requirements of 3.12.17 of MIL-PRF-18148/3.“ “4.5.20 Electrical

20、 performance. Measure the resistance of the current path from the terminal block to the receptacle pins.“ 5.5 Modify the following paragraph: 6.9 Supersession data. Delete the text and insert: “Receptacles previously procured to MS3509 are superseded by MIL-PRF-18148/3. The MS3509-32 is a form, fit,

21、 and function replacement for the MS3509-28, but existing stocks of the MS3509-28 may be used until exhausted.“ TABLE I. Receptacle descriptions. MS part no. Receptacle assembly Style Electrical connections Maximum weight (lbs.) MS3509-1 through -31 obsolete (with the exceptions of -14, -20, and -30

22、). MS3509-20 MS3509-20 consists of one MS3509-30 less “O“ ring plus one MS3509-14 gasket. 1 (Pink) Threaded posts 0.46 MS3509-28 With terminal blocks installed 1 (Blue) Hollow posts 0.46 MS3509-30 Without terminal blocks installed 1 (Pink) Threaded posts 0.46 MS3509-32 With terminal blocks installed

23、 1 (Black) Solid posts 0.46 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 5 TABLE II. Qualification inspection of receptacles. Test number Examinations and tests Qualification sample number Conformance inspection sample number Requi

24、rement paragraph 1/ Method of inspection paragraph 1/ 1 2 3 1 2 1 INCOMING INSPECTION X X X X X 3.12.1 4.5.12 VISUAL AND MECHANICAL X X X X X 3.10, 3.12.2 4.5.23 DIMENSIONS X X 3.12.3 4.5.34 WEIGHT X X X X X 3.12.4 (S) 4.5.45 ELECTRICAL PERFORMANCE X X X X X 3.11 4.5.20 (N)6 STRESS TESTS AT 77F X X

25、X X X - - 6a Dielectric strength X X X X X 3.11, 3.12.5 4.5.6.16b Insulation resistance X X X X X 3.11, 3.12.6 4.5.7.16c Receptacle strength X X X X X 3.11, 3.12.9 4.5.10 (S)7 STRESS TESTS AT -65F X - - 7a Dielectric strength X 3.11, 3.12.5 4.5.6.27b Insulation resistance X 3.11, 3.12.6 4.5.7.28 STR

26、ESS TESTS AT 160F X - - 8a Dielectric strength X 3.11, 3.12.5 4.5.6.38b Insulation resistance X 3.11, 3.12.6 4.5.7.39 LIFE X X X 3.11, 3.12.10 4.5.11.210 TEMPERATURE SHOCK X 3.11, 3.12.11 4.5.12,4.5.6.1 11 MECHANICAL SHOCK X 3.11, 3.12.12 4.5.13,4.5.6.1 12 HUMIDITY X 3.11, 3.12.14 4.5.14,4.5.7.1 13

27、IMMERSION X 3.10, 3.11, 3.12.15 4.5.15,4.5.7.1, 4.5.10 (S) 14 SALT FOG X X X 3.10, 3.11, 3.12.15 4.5.16,4.5.7.1, 4.5.10 (S) 15 VIBRATION X 3.11, 3.12.13 4.5.17.2,4.5.6.1 16 AIR TIGHTNESS TEST X X X 3.11, 3.12.16 4.5.1817 PLATING ADHESION X X X 3.11, 3.12.17 (N) 4.5.19 (N)1/ All paragraphs referenced

28、 are in MIL-PRF-18148, except those annotated with an (N) or (S). Paragraphs with an (N) are new paragraphs added by the specification sheet and paragraphs with an (S) are paragraphs that have been modified by the specification sheet. Provided by IHSNot for ResaleNo reproduction or networking permit

29、ted without license from IHS-,-,-MIL-PRF-18148/3 6 TOP FRONT AND RIGHT SIDE FIGURE 1. Dimensions and configuration for MS3509-32 receptacle. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 7 FIGURE 1. Dimensions and configuration for

30、MS3509-32 receptacle - Continued. 82 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 8 FIGURE 2. Dimensions and outline configuration for MIL-18148/3 (MS3509) style 1 receptacles other than MS3509-32. Provided by IHSNot for ResaleNo r

31、eproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 9 FIGURE 3. Dimensions and detailed configuration for MIL-PRF-18148/3 (MS3509) style 1 receptacles other than MS3509-32. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

32、MIL-PRF-18148/3 10 FIGURE 4. Section views for MIL-PRF-18148/3 (MS3509) style 1 receptacles other than MS3509-32. .203 RAD (TYP) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 11 .315 +.005/-.000 .037 (REF) FIGURE 4. Section views fo

33、r MIL-PRF-18148/3 (MS3509) style 1 receptacles other than MS3509-32 Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 12 FIGURE 5. Dimensions and outline configuration for MIL-PRF-18148/3 (MS3509) style 2 receptacles. Provide

34、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 13 FIGURE 6. Receptacle electrical connections (threaded post). .015 RAD Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 14 FIG

35、URE 7. Receptacle terminal block for MIL-PRF-18148/3 (MS3509) style 1 receptacles other than MS3509-32. FIGURE 8. Test screw. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 15 FIGURE 9. Receptacle assemblies for PIN MS3509-20 and -30

36、. FIGURE 10. Gasket for style 1, PIN MS3509-14. .190/.208 DIA 4 HOLES NOTES: 1. ALL DIMENSIONS ARE TYPICAL. 2. ALL TOLERANCES ARE .062 + .010 UNLESS OTHERWISE SPECIFIED.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-18148/3 16 CONCLUDING MAT

37、ERIAL Custodians: Preparing activity: Army - AV Navy - AS Navy - AS Air Force - 85 DLA - CC Agent: Navy - SH Review activities: (Project 5935-2011-014) Army - CR, MI Air Force - 99 DLA - GS NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-