NAVY MIL-I-81316 A (3)-1973 INITIATOR CARTRIDGE ACTUATED DELAY MARK 11 MOD 0《MARK 11 MOD 0火药驱动起始延迟装配件》.pdf

《NAVY MIL-I-81316 A (3)-1973 INITIATOR CARTRIDGE ACTUATED DELAY MARK 11 MOD 0《MARK 11 MOD 0火药驱动起始延迟装配件》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-I-81316 A (3)-1973 INITIATOR CARTRIDGE ACTUATED DELAY MARK 11 MOD 0《MARK 11 MOD 0火药驱动起始延迟装配件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 - MIL-I-BL3ibA (3) 13 R 99999Ob 0358789 7 m MIL-1-8 i 3 16A(AS) . AMENDMENT 3 16 Jy 1973 . SUPERSEDING AMENDMENT 2 3 1 October 1968 * MILITARY SPECIFICATION INITIATOR, CARTRIDGE ACTUATED, MARK 11 MOD O This amendment forms a part of Military Specification MIL-I-81316A(AS) of 17 April 1967, and has

2、been approved by the - Naval Air Systems Command, Department of the Navy. Page 2 Under “PUBLICATIONS”, delete “BUSANDA Instruction 4030.17” and title. 2.2, under “CODE OF FEDERAL REGULATIONS”, delete “49 CFR 71-78” and title, and substitute: “49 CFR 171-178 Transportation, Explosives and other Dange

3、rous Articles” Page 3 3.3, delete line 2 and substitute “the MARK 36 MOD O delay cartridge and the shear pin, Drawing 2518129 of DL 2518122, are defined as primary components.” +so -0 3.5.2, line 3, delete “500 psi psi” and substitute “650 psi maximum”. Page 4 3.7.1, delete paragraph in its entirety

4、. t Page 7 4.6.1 , delete and substitute: “4.6.1 Packaginp packing and marking. (M102) The packaging-and packing of cartridges and the container markings shall be in accordance with Section 5. Quality - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

5、-MIL-I-L3Lb (3) 13 97990b -354790 5 I1 MILI-8 13 1 6A(AS) AMENDMENT 3 conformance inspection shall be conducted in accordance with the inspection criteria on the applicable drawings referenced in Section 5.” 4.7.1.2, line 4, delete “500 psi psi” and substitute “650 psi maximum”. -0 Page 8 4.7.2.3.1,

6、 line 7, delete “24 hours” and substitute “a minimum of 12 hours”. 4.7.2.3.1, line 10, delete “500 psi psi” and .substitute “659 psi -0 maximum”. 4.7.2.3.2.1, delete paragraph in its entirety. Page 9 5.1.3, last line, delete “49 CFR 71-78” and substitute “49 CFR 171-178”. 5.2.3, last line, delete “4

7、9 CFR71-78” and substitute “49 CFR 171-178”. 5.3.1, last line, delete “49 CFR 71-78” and substitute “49 CFR 171-178”. 5.3.2, delete and substitute: “5.3.2 Normal markings. Unless otherwise specified in the contract or orGa, the marking information on unit packages and shipping containers shall be as

8、 specified on Drawings 2518132 and 2518179, respectively, of DL 2518122. The specified marking information shall be applied to the containers in accordance with the applicable provisions of MIL-STD- 129.” Page 10 6.1, line 3, between “T2” and “aircraft”, insert “(T2J)”. 6.3.1, delete and substitute:

9、 “6.3.1 Test report. The contract or order should specify that results of ballistic tests are to be forwarded to the Naval Air Systems Command (AIR-53222A) and the procuring activity.” 6.4, delete and substitute: “6.4 Definitions. For the purposes of this specification, the following definitions app

10、ly.” _,_ -. . - . . Page2of 3 . .I. - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-I-833LbA (3) L3 m 777770b 0358773 7 II c MIL-1-8 13 1 6A(AS) AMENDMENT 3 Pages 11, 12, 13, and 14. 6.5 and subparagraphs, delete and substitute: “6.5 Explosiv

11、es safety precautions. Safety precautions for explosive-loaded items are contained in DOD 4145.26M, “DOD Contractors Safety Manual for Ammunition, Explosives and Related Dangerous Material”.” t t Proj ect No. 1377-N538 * U. S. GOVERNMENT PRINTING OFFICG 1973- 713- 145/731 -o- . - : - -_ Page 3 of 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-