NAVY MIL-F-50694-1970 FIRING MECHANISM CARTRIDGE ACTUATED 29378-1 REMANUFACTURED METAL PARTS ASSEMBLY《29378-1型由金属零件改造组装的火控发射系统》.pdf
《NAVY MIL-F-50694-1970 FIRING MECHANISM CARTRIDGE ACTUATED 29378-1 REMANUFACTURED METAL PARTS ASSEMBLY《29378-1型由金属零件改造组装的火控发射系统》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-F-50694-1970 FIRING MECHANISM CARTRIDGE ACTUATED 29378-1 REMANUFACTURED METAL PARTS ASSEMBLY《29378-1型由金属零件改造组装的火控发射系统》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-F-50b74 13 H 777770b OLI26705 3 MIL-F- 50694( MU) 18 November 1970 MILITARY SPECIFICATION FIRING MECHANISM, CARTRIDGE ACTUATED, 29378-1 REDWLII?ACTm METAL PARTS ASSEMBLY 1. SCOPE - 1.1 This specification covers Firing Mechanisms P/N 29378-1. The assembly will be ultimately loaded and used to act
2、uate the canopy counter- balance jettison and cinch-down cylinder assembly in the TF102 Aircraft. 2. APPLICABLE DOCUMENTS 2.1 The following documents ofthe issue in effect on date of invitation for bids or request for proposal form a part of this specification to the extent specified herein. SPECIFI
3、CATION Military MIL-A-2550 - Amnunition and Special Weapons, General Specification for S- Military MIL-STD-I05 MIL-STD-109 MIL-STD-413 - Sampling Procedures and Tables for Inspection - Quality Assurance Terms and Definitions - Visual Inspection Guide for Rubber O-Rings by Attributes DRAWINGS Munitio
4、ns Coimiend L. Cg224217 Cg224720 IEL29378-1 - Container, Anmunition, Fiber for Firing - Box, Packing, Amnunition, for Firing - Inspection Equipment List for Firing Mechanism Assembly, P/N 29378-1 Mechanism Assembly, P/N 29378-1 Mechanism, Cartritige Actuated, 29378-1 Assembly - ._- y eeg Industries
5、(Code Ident. No. 12116) 29378-1 - Fira Mechanism, Cartridge Actuated, Assembly FSC 1377 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I_ MIL-F-50674 13 m 7777706 0426706 5 m 1L-F-50694( MU) (Copies of specifications , standards connection with
6、specific procurement procuring activity or as directed by and drawings required by suppliers in functions should be obtained from the the contracting officer,) 2.2 Other publications - The following document forms a part of this specification to the extent specified herein. the issue in effect on da
7、te of invitation for bid or request for proposal shall apply: Unless otherwise indicated, ASA 46.1 - Surface Texture (Application for copies should be addressed to the American Standards Association, 10 East 40th Street, New York, N.Y. 10016). 3. REQUIREMENTS 3.1 General - Materials, parts and assem
8、blies shall comply with.the requirements specified on the applicable drawings, referenced specifications and the following: 3.2. Material - The contractor shall be responsible for selecting from the classification list contained in the raw material intended for use in manufacture. 3.3 Mechanical pro
9、perties - Mechanical properties required by the drawing shall be uniform throughout the part within specified tolerances. Requirements for ali steel parts shall be achieved by quenching and tempering. 3.4 Metal parts assembly - Parts shall be combined to produce an assembly which conforms to the req
10、uirements of the metal parts assembly drawing and the - following: 3.4.1 The remanufactured Firing Mechanism metal parts assembly contain new parts in accordance with Table I: shall TAHLE I Pin, Shear O-Ring Set Screw P TAEE III Total Allowable Defects Per Sample Size Sample Sizes for Major Defects
11、Number of Defects in Class 2 - 3. 4- 7 8 - i9 20 - 43 Over 43 Sample Sizes for Major Defects Number of Defects in Class 2- 3 4- 7 8 - 16 17 - 48 Over 48 - 110 - 150 - 225 1 2 3 4 5 8 2 3 4 5 6 8 11 ; i50 . 225 - - 110 - 2 3 4 3 4 5 4 5 8 6 a 11 8 11 17 - 300 4 5 7 10 i4 5 7 10 i4 20 4 Provided by IH
12、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-F-50694 13 M 7997906 0426709 O W -. MIL-F -5C694( M ) 4.2.2.3 Head, Drawing 29308-1 covering a detail of Drawing 29378-1 Detail CRITICAL Method of Inspection None defined MAJOR 101 . 102. 103 . . . 104. 105. i06
13、. 107. . 108. log u0 . 1ll. 112. Pitch diameter of large thread Major diameter of large thread Pitch diameter of small thread Major diameter of small thread Pitch diameter of set screw thread Major diameter of set screw thread Shear pin hole Metal defect ive Protective finish inadequate or defective
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILF506941970FIRINGMECHANISMCARTRIDGEACTUATED293781REMANUFACTUREDMETALPARTSASSEMBLY293781 金属 零件 改造

链接地址:http://www.mydoc123.com/p-979174.html